PSI Displays HD5002 Manuel utilisateur
www.psidisplays.co.uk
HD CCTV Tester/Test Monitor
Model: HD5002
User Manual
Content
1. Safety information.......................................... 1
2. Function interface........................................... 2
3. Operation ....................................................... 5
3.1 Installing the Battery ............................ 5
3.2 General.................................................. 6
4. Feature ........................................................... 6
5. Feature introduction........................................ 7
5.1 TVI/CVI/AHD/CVBS camera test ......... 7
5.2 Coaxial PTZ control .............................. 8
5.3 RS485 control...................................... 10
5.4 EX-SDI/HD-SDI camera test............... 10
6. XVR display................................................. 11
6.1 HDMI input......................................... 11
6.2 VGA input........................................... 12
7. Cable Tester.................................................. 12
7.1 UTP Cable Tester................................. 12
7.2 Digital cable tracer (Optional) ............. 14
8. U disk reading .............................................. 16
9. Audio test ..................................................... 16
10. Setting........................................................ 17
11. Packing kits ................................................ 17
12. Specifications ............................................. 18
•Safety information
◆ The tester is intended to use in compliance with the local rules of the electrical
usage and avoid to apply at the places which are inapplicable for the use of
electrics such as hospital, gas station etc.
◆ To prevent the functional decline or failure, the product should not be sprinkled
or damped.
◆ The exposed part of the tester should not be touched by the dust and liquid.
◆ During transportation and use, it is highly recommended to avoid the violent
collision and vibration of the tester, lest damaging components and causing
failure.
◆ Don’t leave the tester alone while charging and recharging. If the battery is
found severely hot, the tester should be powered off from the electric source at
once. The tester should not be charged over 10 hours.
◆ Don’t use the tester where the humidity is high. Once the tester is damp, power
off immediately and move away other connected cables.
◆ The tester should not be used in the environment with the flammable gas.
◆ Do not disassemble the instrument since no component inside can be
repaired by the user. If the disassembly is necessary indeed, please contact with the
technician of our company.
◆ The instrument should not be used under the environment with strong
electromagnetic interference.
◆ Don’t touch the tester with wet hands or waterish things.
◆ Don’t use the detergent to clean and the dry cloth is suggested to use. If the dirt
is not easy to remove, the soft cloth with water or neutral detergent can be used.
But the cloth should be tweaked sufficiently.
•Function interface
1_RS485 data transmission indicator: the light is red while the data is being
transmitted
2_Charging indicator: the light is red while the battery is being charged. The light
will automatically turn off if charge completed.
3_Power indicator: the light is green while the tester is turned on
4_Zoom in the image
5_Zoom out the image
6_Focus the image faraway
7_Focus the image nearby
8_Upward, select function, set parameter and tilt the PTZ upward
9_Rightward, select function, set parameter and pan the PTZ rightward
10_Confirm button, enter functions and save settings
11_Downward, select function, set parameter and tilt the PTZ downward
12_Leftward, select function, set parameter and pan the PTZ leftward
13_Setting button, enter the function parameter settings
14_Return/Close: Return and cancel the operation
15_CVBS/AHD/TVI/CVI input (BNC interface)
16_EX/HD-SDI input (BNC interface) （Optional）
17_HDMI input
18_DC 5V 1A power output, USB power bank
19_DC 12V 1A power output, temperately supply power for camera
20_ON/OFF power switch
21_LED light
22_Light power button
23_DC 5V 2A charging interface
24_RS485 Interface: RS485 communication for the PTZ
25_Audio input
26_UTP port, UTP cable tester port/ Cable tracer port (*Optional)
27_VGA input
•Operation
3.1 Installing the Battery
The tester has built-in lithium ion rechargeable battery. The battery inside battery
cabin should be disconnected for safety during transportation!
Prior to the use of the instrument, please take out the battery insulation paper.
Sliding the ON/OFF power switch can power on or off the tester.
Notice: please use 5V 2A adapter to charge when charging. Too high
voltage/current will burn the instrument!
When the battery icon is full or the charge indicator turns off automatically, indicate
the battery charging is completed.
3.2 General
The 5 inch TFT-LCD screen HD CCTV Tester is designed for maintenance and
installation of CVBS, TVI, CVI, AHD cameras, as well as HDMI input, VGA input,
Audio input, PTZ control, PING test, LED Flashlight, DC 12V 1A power output,
etc. Its portability, user-friendly design and many other functions make the CCTV
tester an essential tool for all installers or technicians.
•Feature
● 5 inch TFT-LCD screen, 800*480 resolutions
● RS485 PTZ control, baud 600-115200bps, compatible with more than 30
protocols such as PELCO-D/P, Samsung, Panasonic, Lilin, Yaan, etc
● 8MP TVI test, 3840 x 2160P 12.5/15 FPS, coaxial PTZ control & call OSD
menu
● 8MP AHD test, 3840x2160P 15 FPS, coaxial PTZ & call OSD menu
● 8MP CVI test, 3840 x 2160P 12.5/15FPS, coaxial PTZ & call OSD menu
● 8MP EX-SDI test, 3840 x2160P 25/30FPS, coaxial PTZ & call OSD menu
(*Optional)
● HD-SDI test, 1920 x1080P 25/30/50/60 FPS, coaxial PTZ & call OSD menu
(*Optional)
● 3G-SDI test, 1920 x1080P 50/60 FPS, coaxial PTZ & call OSD menu
(*Optional)
● CVBS camera test, PTZ controller
● DC12V/1A power output, camera can be powered from DC 12 Voltage.
● DC 5V 1A power output, support reading USB disk
● Audio in, support record and save the audio.
● Improvement cable tester, UTP cable, telephone cable etc order and connectivity
test, can save testing report, if special number, need customized. Can detect the
near-end, mid-end and far-end fault point of RJ45 cable connector
● Digital Cable tracer, search BNC cable, network cable and telephone cable from
the mess cables. Cable tracer and UTP cable test app in the same
interface(*Optional)
● 3.7 V /5200mAh Li-ion Battery, after 4 hours charging, working time lasts 6.5
hours
•Feature introduction
• TVI/CVI/AHD/CVBS camera test
Connect camera to “AHD/CVI/TVI” port, enter “Auto HD” app. Can auto
recognize AHD/CVI/TVI/CVBS signal and display the image, as well as display
the camera type and frame.
• Coaxial PTZ control
When enter “PTZ” option, press key switch to “menu setting”, and switch to
“key (open)” or “OK” option, press key to call out the camera main menu.
• RS485 control
Support RS485 control, baud 600-115200bps, compatible with more than 30
protocols such as PELCO-D/P, Samsung, Panasonic, Lilin, Yaan, etc. Can set PTZ
pan speed and Tilt speed, call set preset position. In the Auto HD/CVBS IN
interface, press “SET” , can set RS485 protocol, Port, Baud, Address, PTZ, etc.
• EX-SDI/HD-SDI camera test
Connect camera to “SDI” port, enter “Auto HD” app, and select “SDI” to enter
SDI interface, can display the camera image, and will display the resolution and
frame rate in top-left corner, support up to 4K/8MP 3840x2160p 25/30fps EX-SDI
camera test, coaxial PTZ, call OSD menu and RS485 control.
•XVR display
• HDMI input
Connect one end of HDMI cable to Tester’s “HD IN” port, other end connect to
XVR’s “HDMI” port, enter “HDMI input” app, can receive the real-time
audio and video signal from XVR, and will display the resolution and frame rate in
top-left corner, support up to 4K/3840x2160p30fps resolution.
• VGA input
Connect one end of VGA cable to Tester’s “VGA” port, other end connect to
XVR’s “VGA” port, enter “VGA input” app, can receive the real-time video
signal from XVR, support up to 1920x1200 resolution.
•Cable Tester
•UTP Cable Tester
Connect one end of LAN cable or telephone cable to Tester’s UTP/SCAN port,
other end connect to the UTP port of Cable tester or cable tracer (*optional).
Cable tester can test cable sequence, continuity and cable type, can detect near /
medium / far end fault of RJ45 cable connector, display the number of the remote
kit (Remote default No.255).
Table des matières
Manuels Équipement de test populaires d'autres marques
SMART
SMART KANAAD SBT XTREME 3G Series Manuel utilisateur
Agilent Technologies
Agilent Technologies BERT Serial Manuel utilisateur
Agilent Technologies
Agilent Technologies N3280A Manuel utilisateur
Vernier
Vernier Go Direct Voltage Manuel utilisateur
Lifeloc
Lifeloc R.A.D.A.R. Manuel utilisateur
Fluke
Fluke T5-600 Instructions d'utilisation et d'installation
