PSA Supa8 Manuel utilisateur

SUPA8 Quick Setup & User Manual

CONTENTS

QUICK SETUP & INSTALLATION

FACTORY DEFAULTS................................................................................. 1

INSTALLATION OF THE SECURITY SYSTEM...................................... 2

COMMISSIONING THE DIALLER PANEL ............................................. 5

ZONE INPUT CONNECTIONS.................................................................... 7

PANEL DIAGRAM......................................................................................... 8

USER MANUAL

THE SUPA8 KEYPAD ................................................................................... 9

SUPA8 INDICATOR LIGHTS.......................................................................... 10

KEYPAD BEEPER OPERATION ....................................................................... 10

KEYPAD LOCKOUT ....................................................................................... 11

KEYPAD ENTRY ERRORS .............................................................................. 11

SUPA8 OPERATION ................................................................................... 12

KEYPAD KEY FUNCTIONS............................................................................. 12

OPERATION OF ALL KEYS.............................................................................. 12

HOW TO TURN THE SYSTEM ON.......................................................... 17

AWAY MODE (USING YOUR USER CODE).................................................... 17

AWAY MODE (USING SUPER CODES) .......................................................... 19

HOME MODE (USING YOUR USER CODE)..................................................... 20

HOME MODE (USING QUICK HOME)............................................................ 20

HOW TO TURN THE SYSTEM OFF........................................................ 21

ISOLATING ZONES.................................................................................... 21

PROGRAMMING USER CODES .............................................................. 22

PERSONAL REPORTING.......................................................................... 23

PROGRAMMING TELEPHONE NUMBERS.......................................... 24

OPERATION BY TELEPHONE................................................................. 25

FREQUENTLY ASKED QUESTIONS ...................................................... 26

SYSTEM RECORD SHEET...................................................................... 278

SUPA8 Quick Setup

Quick Setup & Installation

Thank you for purchasing the SUPA8 Security Alarm System, the following is intended

to assist you in the installation of the system. Please read these guidelines before

installation.

Note: In some States of Australia special licensing may be required in order to

install Security Alarms and Associated Equipment. Please check with your

local State Authority for details before commencing installation work.

IMPORTANT:

This section is a brief outline of installation and programming. For additional

information refer to the SUPA8 Installer Manual.

Factory Defaults

THE SUPA8 ALARM SYSTEM COMES FROM THE FACTORY PROGRAMMED AND

READY TO GO. BEFORE MAKING ANY CHANGES, CHECK WHAT IS ALREADY

PROGRAMMED, AS THEY WILL MOST PROBABLY SUIT YOUR NEEDS.

MASTER USER CODE : 1 2 3 4

INSTALLER CODE : 2 5 8 0

ENTRY TIME : 30 seconds

EXIT TIME : 60 seconds

SIREN TIME : 5 minutes

ZONE TYPE Zone 1 : Entry Delay - enables entry exit timer.

Zone 2 : Handover - enables exit timer and entry timer

if Entry Delay Zone entered first.

Zone 3 : Handover - enables exit timer and entry timer

if Entry Delay Zone entered first.

Zone 4 : Instant - immediately sounds siren if violated

when system is armed.

Zone 5 : Instant - immediately sounds siren if violated

when system is armed.

Zone 6 : Instant – immediately sounds siren if violated

when system is armed.

Zone 7 : 24 Hour - sounds sirens if violated whether

system is armed or disarmed.

Zone 8 : 24 Hour - sounds sirens if violated whether

system is armed or disarmed.

NOTE: When Armed in Home Mode Zones 5 and 6 has been programmed to be

isolated.

SUPA8 Quick Setup

Installation of the Security System

Step 1:

Plan out location of all components supplied in your kit as follows:

Suggested Locations for Equipment Mounting

(a) The 8 Zone Master Panel Box should always be located out of sight (i.e.

cupboard, wardrobe or in an area it would not be easily seen).

(b) The 8 Zone Keypad should be situated near the main entry/exit point (usually

inside the main front door).

should be mounted in a prominent position in full view. This would normally

be mounted under the eaves at the front of the house in a corner position. The

strobe light is mounted onto the siren cover.

(d) The Flush Mount Reed Switches are most suitable to be mounted on the front

and back doors.

(e) The Passive Infra Red Detectors (PIR’S) should be situated to cover high

access areas (eg: Hallways and areas of high importance or value).

(f) The Emergency Button should be located in a position for quick easy access

in an emergency or panic situation (suitable position could be a bedside

location).

(g) The Pinkerton Security Alarm Warning Stickers should be placed on the front

face of the Siren cover and on an outside window in clear view.

Note: PIR’s are susceptible to environmental conditions such as wind and air

movement. Windows must be closed when system is armed to avoid possible

false alarms.

Step 2:

(a) Install all cabling to component positions.

(b) Austel approved cables must be installed if the system is to be monitored.

Use two pair (4 core) 14/0.20 and Figure 8 (2 core) 14/0.20.

REMEMBER TO MARK YOUR CABLES.

SUPA8 Quick Setup

Step 3:

(a) Mount devices in the most suitable locations (as suggested in Step 1).

(b) Wire cabling directly into devices.

(Refer to Page 7).

The feature of this resistor is that when installed at the furthest point in the Zone,

tampering or interference with the wiring is not possible without setting off the alarm.

Note: All joints connecting cables to EOL Resistors must be soldered and taped.

Step 4:

(a) Install Master Control Panel and connect all cabling to panel.

(b) A 240V GPO is required adjacent to the Master Control Panel position for the

Plug Pack.

Step 5:

Seal any unused or spare Zones with a 4.7K (EOL) end of line resistor.

Step 6:

Connect Battery, now Switch on Plug Pack supply.

Note: Once the alarm system is powered up, control of the system is handed over,

and managed by the 8 Zone Keypad. All programming for the system is done

via the Keypad.

Step 7:

Upon power up the Zone 3 LED will be on, and the ON-LINE LED will also be on

indicating a system self test.

After the alarm panel has initiated this tests the panel will go into alarm if Zones 7 & 8

(24 hour Zones) are not sealed.

SUPA8 Quick Setup

To DISARM the panel:

(a) On Keypad

Enter: 1234 (all Zone lights will flash)

(b) Followed by: 0(the off key)

Step 8: Walk Test

To check operation of all Zones a Walk Test is recommended.

(a) On Keypad

Enter: 1234(all Zone lights will flash)

(b) Followed by: 5(to initiate a walk test)

The walk test function is now activated.

The Zone LED will light as each Zone is triggered and the siren will squawk momentarily. The

Zone LEDs will remain on to show which Zone has been violated. (Requires only one person

testing).

To deactivate a walk test press the *key.

THE SYSTEM IS NOW OPERATIONAL

To arm and disarm the system enter Master User Code 1234 (factory default) followed

To arm the system enter: 9(ON)

To disarm the system enter: 0(OFF)

Note:The system can also be quick armed by pressing #9

To disarm enter User Code then 0

To change Master User Code or User Codes, please refer to Page 22

This completes the instruction for a Local Panel

SUPA8 Quick Setup

Commissioning the Dialler Panel

Austel Requirements:

Austel requirement’s state that all Dialler Panels connected to the Telephone Network must have

the Telephone connection and termination work performed and completed by a current Austel

Licence Holder.

To Assign for Local Dialling (to a nominated telephone number) for Self

Monitoring Purposes.

Step 1: On Keypad

Enter programming mode: 2580 7

You are now in Programming Mode (ON-LINE light will flash).

Step 2: On Keypad

To set up Personal Reporting format:

Enter: 250 (address number)

Followed by: 2578 (cancels the programming mode)

Step 3: On Keypad

Re-enter programming mode:

Enter: 2580 7

Step 4: On Keypad

Entering of required telephone number/s.

1st Telephone Enter: 128 0391234567 #6 *

2nd Telephone Enter: 144 0411234567 #6 *

Note: (a) The above numbers are examples only. You must enter the correct numbers to dial

according to the Home owner’s requirements. A maximum of two telephone numbers

can be programmed.

(b) The phone numbers can consist of a mix of mobile phones numbers and local phone

numbers. Only one phone number can be programmed if required.

(d) *completes address (allows next address).

Step 5: On Keypad

Exit programming: Enter: *

SUPA8 Quick Setup

System is now operational as a Self Monitored Dialler.

Note: In the event of an alarm, the dialler will emit via the telephone system, a computer

generated siren tone.

If you are installing a Dialler Panel and do not wish to connect to a telephone line, you

MUST default the panel to a local format. (See page 7 of Installer Manual)

To Assign for Pinkerton Security Central Monitoring Station Dialling.

There are two formats that can be selected for central station monitoring; domestic monitoring and

business monitoring. The difference between domestic and business monitoring is that business

monitoring will send opening and closing reports.

Before commencing programming please contact Pinkerton Monitoring Pty Ltd on (03) 9888 9889

for allocation of Dialler Telephone Numbers and Client Identification Number.

Step 1: On Keypad

To enter programming mode.

Enter: 2580 7

You are now in Programming Mode (ON-LINE light will flash).

Enter: 250 3578 (for domestic monitoring)

250 4578 (for business monitoring)

Step 2: On Keypad

Re-enter programming mode:

Enter: 25807

Step 3: On Keypad

To program Central Monitoring Station Telephone Number:

Enter: 128 0391234567 #6 *

Enter: 144 0391234567 #6 *

Note: (a) The above number 03 91234567 is an example only.

(b) If you are only supplied with one central station number please enter

that number into both telephone addresses.

(d) *completes address (allows next address).

SUPA8 Quick Setup

Step 4: On Keypad

To assign Client Identification Account Number (example No:1111).

Enter: 160 1111

Enter: 164 1111

Note: The Account Number must be programmed into both addresses.

The above Account Number is allocated by your Central Monitoring Station.

Enter: *(to exit programming mode).

This system is now operational as a Central Monitoring Station Dialler.

Zone Input Connections

General Examples Only. Refer to installation guidelines supplied with device.

SUPA8 Quick Setup

Panel Diagram

6VAC

SUPA8 User Manual

User Manual

The SUPA8 Keypad

The SUPA8 Keypad controls the operation of the SUPA8 alarm panel. It uses

a series of command entry keys to input codes that can arm, disarm and

program the system. The soft-touch rubber keypad is concealed behind a

hinged lid and a series of System and Zone lights run down the right-hand side

of the fascia.

Table des matières

Manuels Système de sécurité populaires d'autres marques

Inner Range

Inner Range Concept 2000 Manuel utilisateur

Climax

Climax Mobile Lite R32 Instructions de montage

CADDX

CADDX NX-6 Manuel utilisateur

FBII

FBII XL-31 Series Manuel utilisateur

Johnson Controls

Johnson Controls PENN Connected PC10 Manuel utilisateur

Aeotec

Aeotec Siren Gen5 Manuel utilisateur

Blaupunkt

Blaupunkt SA 2700 Manuel utilisateur

IDEAL

IDEAL Accenta Manuel du propriétaire

AJAX

AJAX DoubleButton Manuel utilisateur

Swann

Swann SW-P-MC2 Manuel utilisateur

Ecolink

Ecolink Siren+Chime Manuel utilisateur

Digital Monitoring Products

Digital Monitoring Products XR150 Manuel utilisateur

EDM

EDM Solution 6+6 Wireless-AE Manuel utilisateur

Highway Safety Group

Highway Safety Group EA401 Manuel utilisateur

Siren

Siren LED GSM Manuel utilisateur

Detection Systems

Detection Systems 7090i Instructions de montage

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manuel utilisateur

Siemens

Siemens FDM273 Manuel utilisateur