Proxim Harmony 802.11b Manuel utilisateur

Harmony 802.11b

Access Point

Model 8550

User’s Guide

duced, transmitted, transcribed, stored in a retrieval system or translated into any language in

any form by any means without the written permission of Proxim, Incorporated.

Trademarks

Harmony, RangeLAN, the RangeLAN logo, RangeLAN2, and Proxim are trademarks of

Proxim, Inc. All other trademarks are the property of their respective owners.

Limited Warranty, Disclaimer, Limitation Of Liability

For a period of one (1) year from the date of purchase by the retail customer, Proxim warrants

the Harmony 802.11b Access Point Model 8850 against defects in materials and workmanship.

Proxim will not honor this warranty if there has been any attempt to tamper with or remove the

product’s external foil label.

This warranty does not cover and Proxim will not be liable for any damage or failure caused by

misuse, abuse, acts of God, accidents, or other causes beyond Proxim's control, or claim by

other than the original purchaser.

If, after inspection, Proxim determines there is a defect, Proxim will repair or replace the

Access Point at no cost to you. To return defective merchandise to Proxim please call Proxim

Technical Support 1-408-731-2640 to obtain a Return Merchandise Authorization (RMA)

Number.

In no event shall Proxim, Incorporated be responsible or liable for any damages arising:

❑From the use of the product;

❑From the loss of use, revenue or profit of the product; or

❑As a result of any event, circumstance, action, or abuse beyond the control of Proxim,

Incorporated.;

Whether such damages be direct, indirect, consequential, special or otherwise and whether

such damages are incurred by the person to whom this warranty extends or a third party.

Part # 7360.xxxx

Rev. A

Warranty Return Policy

If you have a problem with the Harmony 802.11b Access Point Model 8550, please call Proxim

Technical Support at 1-408-731-2640. Proxim Technical Support will assist with resolving any

technical difficulties you may have with your Proxim product.

After calling Proxim Technical Support, if your product is found to be defective, you may return

the product to Proxim after obtaining an RMA (Return Materials Authorization) number. The

product must be returned in its original packaging. The RMA number should be clearly marked

on the outside of the box. Proxim cannot be held responsible for any product returned without

an RMA number, and no product will be accepted without an RMA number.

FCC WARNING

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates,

uses, and can radiate radio frequency energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio communications. However, there is

no guarantee that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct the interference by one or

more of the following measures:

❑Reorient or relocate the receiving antenna.

❑Increase the separation between the equipment and the receiver.

❑Connect the equipment into an outlet on a circuit different from that which the receiver

is connected.

❑Consult the dealer or an experienced radio/TV technician for help.

Contents

1. Introduction .................................................................4

The Harmony Family ............................................................................... 5

System Requirements ............................................................................... 6

2. Installation ...................................................................7

Installation Procedure............................................................................... 7

Mounting Option ...................................................................................... 8

LED Indicators ......................................................................................... 9

3. Wirefree Operation ....................................................10

Harmony Architecture............................................................................ 10

The IEEE 802.11b Specification............................................................ 11

Roaming Between Harmony 802.11b Access Points............................. 11

Roaming Guidelines ............................................................................ 12

4. Configuration Parameters ........................................14

Basic Settings....................................................................................... 14

WEP Settings ....................................................................................... 17

Advanced Settings ............................................................................... 17

5. Performance Hints ....................................................19

Microwave Ovens .................................................................................. 19

Range...................................................................................................... 19

6. Troubleshooting ........................................................21

How to Obtain Help with Your LAN Installation.................................. 21

Common Problems and Solutions .......................................................... 21

A. How to Reach Technical Support............................24

B. Harmony 802.11b Access Point Specifications .....25

1. Introduction

Thank you for choosing Proxim’s Harmony 802.11b Access Point Model 8550, a

member of Proxim’s Harmony Wirefree Infrastructure Family. The Harmony product

line is the first wirefree networking solution to embrace all current and future wirefree

LAN standards, including OpenAir, IEEE 802.11b, and future 10 Mbps frequency

hopping and 5 GHz technologies, in a single, homogeneous architecture.

For enterprise customers implementing wirefree solutions, Harmony reduces equip-

ment acquisition costs, installation complexity, and long-term operating costs by

centralizing network management, communication, and security services.

Harmony protects current and future wirefree infrastructure investments by supporting

all leading and forthcoming wireless LAN protocols. Existing RangeLAN2,

OpenAir-compatible and IEEE 802.11b products are all fully compatible with Har-

mony. Customers may seamlessly transition to new LAN standards by adding low-cost

access points without changing the management interface or disturbing existing users.

Harmony further reduces network costs through its SmartArchitecture, the first

wirefree management system to provide one-click, system-wide security updates and

remote office infrastructure management through a single interface. The system may be

managed through a Web-based interface, which provides customizable network maps

and traffic statistics, or through standard enterprise SNMP packages. Harmony’s

SmartArchitecture also greatly reduces the time and expense of installation by avoiding

many of the hidden costs of a wirefree infrastructure.

Harmony Access Points may be connected to any portion of the Ethernet network,

eliminating the need for special wirefree subnets common in other installations. Har-

mony clients also roam seamlessly anywhere there is wirefree coverage, without the

need for extra client software. In addition, Harmony SmartAttach software auto-

discovers and configures new access points upon connection to the Ethernet network,

simplifying installation.

Proxim is the leading supplier of wirefree networking solutions. Proxim’s unmatched

expertise in spread spectrum radio networking technology, combined with the

company’s extensive experience serving the communication needs of the mobile

computing user, have kept Proxim at the forefront of the wirefree LAN market.

The Harmony Family

The Harmony Wirefree Infrastructure Family includes the following products:

❑The Harmony 7560 Access Point Controller centralizes the management,

security, and filtering capabilities of a wirefree LAN. The Access Point

Controller communicates with Harmony Access Points over the Ethernet

network to provide wirefree network access for mobile clients. The Access

Point Controller can support multiple Access Points, even if each Access Point

follows a different wirefree standard.

❑The Harmony Access Point is a networking bridge that operates at Layer 2 of

the OSI networking model. Working in conjunction with a Harmony Access

Point Controller, the Access Point forwards packets between its radio and the

Ethernet network. Two models of the Harmony Access Point are available to

support either the OpenAir or IEEE 802.11b wirefree standards: the model

7550 OpenAir Access Point and the model 8550 802.11b Access Point. Note

that only the Harmony Power System operates only with the 802.11b Access

Point.

❑The Harmony PC Card is a wirefree LAN adapter that fits into a PCMCIA

Type II slot in a laptop computer. Two models of the Harmony PC Cards are

available to support either the OpenAir or IEEE 802.11b wirefree standards.

❑The optional Harmony Power System provides remote DC power to Har-

mony 802.11b Access Points over the unused pins of a twisted pair Ethernet

cable.

System Requirements

To begin using the Harmony 802.11b Access Point, you need the following minimum

requirements:

❑At least one Harmony Access Point Controller;

❑An Ethernet (10Base-T) or Fast Ethernet (100Base-TX) LAN switch or hub;

and

❑At least one 802.11b PC Card.

2. Installation

This chapter describes the installation procedure for the Harmony 802.11b Access

Point and the LEDs found on the unit.

Installation Procedure

Follow these steps to install the Harmony 802.11b Access Point Model 8550:

Note:

YoumustinstallaHarmonyAccessPointControllerbeforeinstallingaHarmony

Access Point.

1. Determine the best location for the Harmony 802.11b Access Point. Keep in

mind the following considerations:

❑The length of the Ethernet cable that connects the Access Point to the network

must not exceed 100 meters.

❑Try to place the Access Point on a flat, sturdy surface as far from the ground as

possible, such as on top of a desk or bookcase, keeping clear of metal obstruc-

tions and away from direct sunlight.

❑Try to centrally locate the Access Point so that it will provide coverage to all of

the mobile devices in the area.

❑If you are not using the Harmony Power System to supply power to the Access

Point, the distance between the Access Point and a power outlet cannot exceed

the length of the power adapter’s cable.

2. Place the Access Point in the desired location. An optional wall mount is avail-

able for the Access Point. Refer to the section entitled “Mounting Option” later

in this chapter for details.

3. Attach one end of an Ethernet cable to the Access Point and attach the other end

to the 10Base-T port of a network hub, switch, router, or patch panel.

Note:

The Harmony 8550 Access Point does not support 100Base-TX; it only supports

10Base-T.

4. If you are not using the Harmony Power System to supply power to the Access

Point or want to connect the Access Point to both the Power System and an AC

power source, attach one end of the AC power adapter, included in the product

package, to the back of the Access Point and the other end to a power outlet.

Note:

Use the Access Point only with the power adapter supplied by Proxim in the

product package. Using another power supply may damage the Access Point. If

youwanttousetheAccessPointinconjunctionwiththeHarmonyPowerSystem,

refer to the Harmony Power System manual for instructions.

The Status LED, located on the top of the Access Point, will turn green to indicate that

the unit is operational. Note that the Status LED will remain amber if the Access Point

cannot find an AP Controller to partner with.

In addition, the green Link LED will turn on to indicate that the Access Point has a

network connection.

5. The AP Controller will automatically detect and configure the Access Point over

the network. Refer to Chapter 4 and the Harmony Access Point Controller Model

7560 User’s Manual for more information on how to configure an Access Point.

Mounting Option

The Harmony 802.11b Access Point is designed to sit on a desktop. In addition, an

optional hardware bracket is available for purchase so that the unit may be mounted to

a wall or ceiling.

Follow these steps to attach the mounting bracket to the Access Point:

1. Remove the 2 rubber feet on the bottom of the Access Point. Note that the rubber

feet are attached to the unit with an adhesive.

2. Underneath the rubber feet there are 3 unthreaded mounting holes that accept M5

thread forming screws. Align the holes of the mounting bracket with these holes.

3. Locate the screws provided with the mounting hardware.

4. Insert the screws into the 3 holes of the mounting bracket and Access Point (i.e.,

the holes aligned in Step #2 above).

5. Tighten the screws with a screwdriver to attach the mounting bracket to the

Access Point.

LED Indicators

There are three LEDs on the top panel of the Harmony 8550 802.11b Access Point:

❑Status LED: This LED, located on the right side (with the unit orientated so

that you can read the Proxim logo), is green when the unit is powered up and

operational. The LED is amber during initialization and when the Access

Point is not partnered with a Harmony AP Controller. If there is an internal

problem with the unit, the LED will turn red. If the Status LED turns red, try

recycling power to the unit. If the LED remains red, contact Proxim Technical

Support for assistance.

❑Radio LED: This LED, located in the center of the three LEDs, blinks green

when the Access Point is transmitting data packets over its radio.

❑Ethernet LED: This LED, located on the left side, blinks green when the

Access Point is transmitting data over the 10Base-T Ethernet port.

There is also one LED on the back panel of the Harmony 8550 802.11b Access Point:

❑Link LED: This LED, located between the power connector and the

10Base-T port, will turn green when the Access Point has a physical connec-

tion to the Ethernet network.

Autres manuels pour Harmony 802.11b

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Proxim Point d'accès sans fil

Proxim

Proxim MP11 5012-SUI Manuel utilisateur

Proxim

Proxim RangeLAN2 7500 Manuel utilisateur

Proxim

Proxim ORiNOCO AP-700 Manuel utilisateur

Proxim

Proxim 7550 Manuel utilisateur

Proxim

Proxim Skyline Manuel utilisateur

Proxim

Proxim Harmony Manuel utilisateur

Proxim

Proxim ORiNOCO AP-700 Manuel utilisateur

Proxim

Proxim 7550 Manuel utilisateur

Proxim

Proxim Orinoco AP-4000MR Manuel utilisateur

Proxim

Proxim Antenna Tsunami MP.11 Manuel utilisateur

Proxim

Proxim Tsunami 800 series Manuel

Proxim

Proxim Antenna Tsunami MP.11 Manuel utilisateur

Proxim

Proxim RANGELAN2 7510 Manuel utilisateur

Proxim

Proxim ORiNOCO AP-700 Manuel utilisateur

Proxim

Proxim ORiNOCO AP-800 Manuel de programmation

Proxim

Proxim ORiNOCO AP-8000 Manuel utilisateur

Proxim

Proxim ORINOCO AP-2000 Manuel utilisateur

Proxim

Proxim Edge MP-1015-CPE Manuel

Proxim

Proxim Harmony 802.11b Manuel utilisateur

Proxim

Proxim ORiNOCO AP-700 Manuel utilisateur

Proxim

Proxim Edge MP-1035-CPE Manuel de programmation

Proxim

Proxim ORiNOCO AP-800 Manuel

Proxim

Proxim Tsunami Multipoint MP-820-BSU-100 Manuel utilisateur

Proxim

Proxim ORINOCO AP-2000 Manuel utilisateur

Manuels Point d'accès sans fil populaires d'autres marques

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manuel utilisateur

Ubiquiti

Ubiquiti NanoStation NSM2 Manuel utilisateur

Cisco

Cisco Aironet 1550 Series Manuel utilisateur

Aruba

Aruba IAP-335 Manuel utilisateur

Advantek Networks

Advantek Networks AWN-AP-54MR Manuel utilisateur

IP-COM

IP-COM AP355 Manuel utilisateur

Buffalo

Buffalo AirStation WLA-L11G Manuel utilisateur

EnGenius

EnGenius EnStationACv2 Manuel utilisateur

D-Link

D-Link DAP-3662 Manuel utilisateur

xG Technology

xG Technology xMax CN1300 Manuel utilisateur

Widelink

Widelink ezWave WAP-1100 Series Manuel utilisateur

Edimax

Edimax CAP1200 Manuel utilisateur

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manuel utilisateur

Aruba

Aruba AP-203R Manuel utilisateur

LuXout Shades

LuXout Shades LUXSHADE MOTION Manuel utilisateur

CreatComm

CreatComm TB5F Manuel utilisateur

SineDigital

SineDigital MW-1500AP(H) Manuel utilisateur

TP-Link

TP-Link AP9650 V1 Manuel utilisateur