Protos Integral Manuel utilisateur
Protos®Integral
www.protos.at
User Manual
GB
1
5
6
2
3
4
GB
1. Adjustments for perfect comfort of wear and optimal safety
1.1 Adjusting for head size:
1.3 Fasten chin strap:
Push the neck guard towards the inside of the helmet
until it snaps into place (with a slight click). In this positi-
on you can see the right and left adjustment straps (see
circle Fig. 3). Use these to adjust the Protos® Integral
safety helmet to your head size.
Slide the adjustment straps (Fig. 3) to the
inside or outside (to adjust for smaller or larger
head size) and fix them in the desired position.
Please make sure to adjust both sides equally
to ensure that the helmet will sit straight on
your head! The lines on the neck guard holder
serve as orientation (see circle).
Once you have adjusted and set both sides,
push the neck guard back into its initial positi-
on. The helmet should now fit firmly but not be
too tight. If the helmet does not fit your head
comfortably, readjust the settings.
Push the adaptor button towards
the outer shell. Now you can select
one of the three ride heights by
pushing the button in our out. Here,
too, make sure to make the same
adjustments on both sides!
You make adjustments to se-
lect one of 3 variable ride
heights directly to the left
and right of the neck guard.
If you have a helmet with hearing
protection, it is easiest to get at the
adjustment straps if you put the ear
protectors in the stand-by position
(see Fig. 14).
TIP!
Neck Guard
Open the chin
strap as shown in
the illustration.
Neck Guard Holder
Adjustment Straps
Back snap fastener
Front snap fasteners
03
7
9
8
10
11
12
13
TIP!
Push the “back snap faste-
ner” into the socket in the
back under the neck guard
on the inside of the helmet
by pushing down hard.
Now pull the chin strap
through the guides on both
sides of the back part of the
neck guard (to do so, it is
best to push the neck guard
outwards again).
There are two more fasteners at
the front of the chin strap (Fig.
6). Snap both of these into the
sockets on both sides (circles).
Lock them into place by pulling
slightly, so that they point to the
inside of the helmet (Fig. 11).
Once you have made final
adjustments to your chin
strap, the excess part of the
strap can be cut off and the
cut edge can then be melted
using a lighter.
Make sure the tension
of the chin strap is the
same on both sides!
14 15
16
17
18
19
Put the ear protectors into the
active position so that they fit
closely over your ears.
1.4 Adjusting the ear protectors:
To adjust for optimal height, push the
ear protectors up or down until they fit
comfortably over your ears.
To put the ear protectors back into the
stand-by position, pull them outward
a little and push them back with two
fingers (also see Fig. 14).
Stand-by position Active position
The pressure, with which the ear pieces fit
over the ears, can be adjusted. To do so,
remove the ear protectors (in the active
position, Fig. 15). «Press» on the red tab
to pull the ear protectors from the shell of
the helmet.
Now turn the pressure regu-
lator with a 1- or 2-cent coin
(10 or 50 centime CHF) to
increase (+) or decrease (-)
the pressure.
Take the ear protection incl. bracket and
slide it into the corresponding clasp.
Attention! The arrows on the ear pie-
ces should point to the front of the helmet
(Fig. 15 and 16).
GB
05
21
20
22
23
25
24
26
Remove the crown and
neck pad from the Velcro
fastening by pulling on it
and exchange with repla-
cement pads.
2. How to exchange parts:
If parts of your Protos® Integral safety helmet become worn or damaged, or if they must be cleaned, they can be
easily exchanged.
2.1 Changing the brow, crown and neck pad:
Remove the brow pad held by
plastic clips from the brow pad
holder and clip in the new and/
or dry brow pad starting from the
right or left.
Open the visor, which is
attached to round mounts
on the inside.
Pull strongly to remove the
visor from the mounts.
2.3 Changing the ear piece pads:
First, remove the ear
protectors from the helmet
shell (also see Fig. 17)
Firmly hold the ear piece in your hand
and use your index and middle finger
to hook under the pad from the side.
The pad can be removed by lightly
pulling on it.
Now place the new pad on the ear
piece and press down evenly.
Autres manuels Protos Accessoires pour motos
Manuels Accessoires pour motos populaires d'autres marques
SRC
SRC B-TRK502-01-01-SL Manuel utilisateur
3M
3M Speedglas 9100 MP Manuel utilisateur
hepco & becker
hepco & becker 6307520 00 01 Manuel utilisateur
HOMCOM
HOMCOM AA0-077 Manuel utilisateur
hepco & becker
hepco & becker 6307558 00 01 Manuel utilisateur
Wunderkind Custom
Wunderkind Custom 106503-F15 Guide de l'utilisateur
