Protech BE-0981 Series Manuel utilisateur

USER

MANUAL

BE-0981

3.5”SBCwithIntel®AtomTM

x5/x7/Celeron®N3000/

Pentium®N4000SeriesSoC

BE-0981 M3

BE-0981

3.5 SBC with Intel®AtomTM x5/ x7/

Celeron®N3000/ Pentium®N4000 Series

SoC

All trademarks and registered trademarks mentioned herein are the

property of their respective owners.

This manual is copyrighted in November 2017. You may not

reproduce or transmit in any form or by any means, electronic, or

mechanical, including photocopying and recording.

DISCLAIMER

This user’smanual is meant to assist users in installing and setting up

the system. The information contained in this document is subject to

change without any notice.

CE NOTICE

This is a class A product. In a domestic environment this product may

cause radio interference in which case the user may be required totake

adequate measures.

FCC NOTICE

This equipment has been tested and found to comply with the limits for

a Class A digital device, pursuant to part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area is

likely to cause harmful interference in which case the user will be

required to correct the interference at his own expense.

You are cautioned that any change or modifications to the equipment

not expressly approve by the party responsible for compliance could

void your authority to operate such equipment.

CAUTION: Danger of explosion may occur when the battery

is incorrectly replaced. Replace the battery

only with the

same or

equivalent type recommended by the manufacturer.

Dispose of used batteries according to the manufacturer’s

instructions.

WARNING: Some internal parts of the system may have high

electrical voltage. We strongly recommend that only qualified

engineers are allowed to service

and disassemble the

system. If any damages should occur on the system and are

caused by unauthorized servicing, it will not be covered by

the product warranty.

Contents

1Introduction.........................................................................................1-1

1.1 About This Manual ....................................................................1-2

2Getting Started....................................................................................2-1

2.1 Packing List...............................................................................2-2

2.2 BE-0981 Specifications.............................................................2-3

2.3 Safety Precautions....................................................................2-6

3Hardware Configuration.....................................................................3-1

3.1 JUMPER & CONNECTOR QUICK REFERENCE TABLE........3-2

3.2 COMPONENT LOCATIONS .....................................................3-3

3.2.1 Top View of BE-0981RB-**N .............................................3-3

3.2.2 Bottom View of BE-0981RB-**N........................................3-4

3.2.3 I/O View of BE-0981RB-**N ..............................................3-4

3.3 HOW TO SET JUMPERS .........................................................3-5

3.4 Setting Connectors and Jumpers..............................................3-7

3.4.1 COM3 and COM4 PIN9 Definition Selection Guide..........3-7

3.4.2 COM PORT .......................................................................3-8

3.4.3 VGA PORT ......................................................................3-10

3.4.4 DISPLAY PORT...............................................................3-10

3.4.5 LAN PORT.......................................................................3-11

3.4.6 Dual USB 3.0 PORT (USB1)...........................................3-12

3.4.7 USB 3.0 PORT (USB2) ...................................................3-12

3.4.8 USB 2.0 PORT (USB3) ...................................................3-13

3.4.9 Programmable GPIO PIN HEADER................................3-13

3.4.10 I2C WAFER.....................................................................3-13

3.4.11 DC POWER INPUT CONNECTOR.................................3-14

3.4.12 MINI PCI EXPRESS SLOT .............................................3-15

3.4.13 mSATA Connector ...........................................................3-16

3.4.14 LVDS CONNECTOR .......................................................3-17

3.4.15 SLIDE SWITCH FOR LVDS RESOLUTION SELECTION

.........................................................................................3-18

3.4.16 FRONT PANEL CONNECTOR........................................3-21

3.4.17 HD AUDIO CONNECTOR...............................................3-21

3.4.18 PANEL INVERTER CONNECTOR..................................3-22

3.4.19 SATA 3.0 CONNECTOR..................................................3-22

3.4.20 SATA Power CONNECTOR ............................................3-22

3.4.21 BIOS RESET CONNECTOR...........................................3-23

3.4.22 LVDS BACKLIGHT CONTROL SELECTION..................3-23

3.4.23 LVDS VCC VOLTAGE SELECTION................................3-24

3.4.24 LVDS PWM/Backlight Enable Sequence Setting............3-25

3.4.25 CLEAR CMOS DATA SELECTION .................................3-26

4Software Utilities.................................................................................4-1

4.1 Introduction................................................................................4-2

4.2 Installing Intel®Chipset Software Installation Utility..................4-5

4.3 Installing Hotfix Driver Utility .....................................................4-6

4.4 Installing VGA Driver Utility.......................................................4-7

4.5 Installing Intel®Trusted Execution Engine Driver......................4-8

4.6 Installing LAN Driver Utility........................................................4-9

4.7 Installing Sound Driver Utility..................................................4-10

4.8 Installing Serial IO Driver Utility...............................................4-10

iii

5BIOS SETUP ........................................................................................5-1

5.1 Introduction................................................................................5-2

5.2 Accessing Setup Utility..............................................................5-3

5.3 Main...........................................................................................5-6

5.4 Advanced ..................................................................................5-8

5.4.1 Advanced - ACPI Settings.................................................5-9

5.4.2 Advanced – Onboard Device Configuration....................5-10

5.4.3 Advanced – Hardware Monitor........................................5-11

Smart Fan Mode Configuration (BE-0981RB doesn’t support this

function).......................................................................................5-13

Smart Fan Mode Configuration - [Manual Duty Mode] (BE-0981RB

doesn’t support this function) ......................................................5-14

5.4.4 Advanced - F81846 Watchdog........................................5-15

5.4.5 Advanced - S5 RTC Wake Settings ................................5-16

S5 RTC Wake Settings [Fixed Time]...........................................5-17

S5 RTC Wake Settings [Dynamic Time]......................................5-18

5.4.6 Advanced - CPU Configuration .......................................5-19

Socket 0 CPU Information...........................................................5-20

CPU Power Management Configuration.....................................5-21

5.4.7 Advanced - F81846 Super IO Configuration...................5-21

F81846 Super IO Configuration - Serial Port 1 Configuration.....5-23

F81846 Super IO Configuration - Serial Port 2 Configuration.....5-24

F81846 Super IO Configuration - Serial Port 3 Configuration.....5-25

F81846 Super IO Configuration - Serial Port 4 Configuration.....5-26

5.4.8 Advanced - USB Configuration .......................................5-27

5.4.9 Advanced - Platform Trust Technology............................5-28

5.5 Chipset ....................................................................................5-29

5.5.1 Chipset - North Bridge.....................................................5-30

5.5.2 Chipset - South Bridge ....................................................5-31

South Bridge - HD-Audio Configuration ......................................5-32

South Bridge - LPSS Configuration.............................................5-33

South Bridge - PCI Express Configuration..................................5-34

South Bridge - SATA Drives.........................................................5-38

South Bridge - Miscellaneous Configuration...............................5-39

5.6 Security ...................................................................................5-40

5.7 Boot.........................................................................................5-42

5.8 Save & Exit..............................................................................5-44

Appendix A Technical Summary ................................................A-1

BE-0981 Block Diagram ...........................................................................A-2

Interrupt Map ............................................................................................A-3

I/O MAP..................................................................................................A-20

Memory Map...........................................................................................A-22

Configuring WatchDog Timer .................................................................A-24

Flash BIOS Update.................................................................................A-27

BE-0981 SERIES USER MANUAL

Page: 1-1

1Introduction

This chapter provides the introduction for the BE-0981

system as well as the framework of the user manual.

The following topics are included:

•About This Manual

Chapter 1 Introduction

BE-0981 SERIES USER MANUAL

Page: 1-2

1.1 About ThisManual

Thank you for purchasing our BE-0981 system. The BE-0981 provides faster

processing speed, greater expandability and can handle more tasks than before. This

manual is designed to assist you how to install and set up the whole system. It

contains 5 chapters and 1 appendix. Users can configure the system according to their

own needs. This user manual is intended for service personnel with strong hardware

background. It is not intended for general users.

The following section outlines the structure of this user manual.

Chapter 1 Introduction

This chapter provides the introduction for the BE-0981 system aswell asthe

framework of the user manual.

Chapter 2 Getting Started

This chapter describes the package contents and outlines the system specifications.

Read the safety reminders carefully on how totake care of your system properly.

Chapter 3 Hardware Configuration

This chapter outlines the locations of the motherboard components and their

respective functions.You will learn how to set the jumpers and configure the system

to meet your own needs.

Chapter 4 Software Utilities

This chapter contains helpful information for proper installations oftheIntel®Chipset

Software Installation Utility, Hotfix Driver Utility, VGA Driver Utility, Intel®

Trusted Execution Engine Driver Utility, LAN Driver Utility,Sound Driver Utility

and Serial IO Driver Utility.

Chapter 5 BIOS Setup

This chapter indicates you how tochange the BIOS configurations.

Appendix A Technical Summary

This appendix provides the information about the allocation maps for BE-0981

block diagram, system resources, Watchdog Timer Configuration and Flash BIOS

Update.

BE-0981 SERIES USER MANUAL

Page: 2-1

2Getting Started

This chapter provides the information for the BE-0981

system. It describes the package contents and outlines the

system specifications.

The following topics are included:

•Package List

•System Specification

•Safety Precautions

Experienced users can go to Chapter 3 Hardware

Configuration on page 3-1 for a quick start.

Table des matières

Autres manuels protech Ordinateur monocarte

protech

protech BE-0966 Manuel utilisateur

Manuels Ordinateur monocarte populaires d'autres marques

WIN Enterprises

WIN Enterprises PL-80910 Manuel utilisateur

AXIOMTEK

AXIOMTEK SBC81206 Series Manuel utilisateur

Embest

Embest SOM-PH8800 Manuel utilisateur

SeaLevel

SeaLevel SBC-R9 Manuel utilisateur

SMART Embedded Computing

SMART Embedded Computing ATCA-8310 Manuel utilisateur

WinSystems

WinSystems PPM-LX800-G Manuel utilisateur

GIGAIPC

GIGAIPC QBiX-PPC Series Manuel utilisateur

OLIMEX

OLIMEX A10S-OLinuXino-MICRO Manuel utilisateur

Commell

Commell FS-978 Manuel utilisateur

GIGAIPC

GIGAIPC QBiP-8665A/ Manuel utilisateur

VersaLogic

VersaLogic Python EBX-11 Manuel utilisateur

Micro Computer Specialists

Micro Computer Specialists IRV-3702 Manuel utilisateur

CompuLab

CompuLab SB-A510 Manuel utilisateur

Boser

Boser HS-7321 Manuel utilisateur

Premier Farnell

Premier Farnell Embest SBC8530 Manuel utilisateur

MicroSys Electronics

MicroSys Electronics miriac SBC-LS1043A2 Manuel utilisateur

Aaeon

Aaeon UP Manuel utilisateur

Portwell

Portwell WUX Series Manuel utilisateur

protech BE-0981 Series Manuel utilisateur

Manuels Ordinateur monocarte populaires d'autres marques