ProSum K5EXT300 Manuel utilisateur

K5EXT300

300m Extender for USB and PS/2 Keyboard,

USB and PS/2 Mouse, VGA, Serial RS232,

Audio and Microphone over Cat 5 UTP cable

User Manual

Date: 7/20/2007

Version : 130

KEXT300 User Manual Rev 1.3

- -

All trademarks in this manual are the properties of their respective trademark owners.

About this manual

This User Guide is the complete reference to the KLE, its functional features and usage. The Complete User

Guide could be found only on the KLE Support CD-ROM disc.

FCC Statement

This equipment has been tested and found to comply with the regulations for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated in a commercial environment. This

equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in

accordance with this User Guide, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference in which case,

the user will be required to correct the interference at his/her own expense.

CE Statement

This is a Class B product. In a domestic environment, this product may cause radio interference, in which

case the user may be required to take adequate measures.

Technical Support

Telephone: 331 4590 6270

email: [email protected].

KEXT300 User Manual Rev 1.3

- -

Contents

INTRODUCTION..............................................................................................................................4

ADVANTAGES AND FEATURES ..........................................................................................................4

PACKAGE CONTENTS ........................................................................................................................4

FRONT-PANEL AND REAR PANEL VIEWS..............................................................................5

K5LC – REMOTE CONSOLE UNIT (300M AWAY FROM COMPUTER) ..................................................5

K5CMLC – COMPUTER MODULE WITH LOCAL CONSOLE (CONNECTED TO THE COMPUTER) ..........5

INSTALLING THE EXTENDER....................................................................................................6

BEFORE YOU INSTALL THE TWO PIECES OF K5EXT300, YOU SHOULD HAVE THESE ITEMS ON THE

CHECKLIST READY: ...........................................................................................................................6

PLAN THE LAYOUT PATH AND DEPLOY THE UTP CABLE FOR EXTENSION .......................................... 6

CONFIGURE THE K5CMLC (LOCAL) ................................................................................................7

CONFIGURE THE K5LC (CONSOLE2) ................................................................................................7

USING THE OSD MENU ................................................................................................................. 8

CHANGING THE HOTKEYS .................................................................................................................8

NAVIGATING INTO THE OSD MENU..................................................................................................8

OSD MENU/MAIN PAGE ................................................................................................................... 8

OSD MENU/VIDEO PAGE .................................................................................................................9

OSD MENU/AUDIO PAGE .................................................................................................................9

OSD MENU/STATUS PAGE .............................................................................................................10

OSD MENU/SERIAL PAGE ..............................................................................................................10

OSD MENU/SYSTEM PAGE .............................................................................................................11

OPTIMIZE THE VIDEO DISPLAY ON THE REMOTE CONSOLE .....................................12

KEXT300 User Manual Rev 1.3

- -

Introduction

Advantages and Features

K5EXT300 is a new KVM extender technology that utilizes CAT5 media technology to extend your console

up to 300m/1000ft away. It allows you to locate your server physically far back from the user due to security

or spatial concerns. It is especially useful for setting up a highly flexible computer/user topology over a long

distance, either over an exhibition room, work floor, security room, locked server room, or other mission-

critical scenarios. This advanced KVM extender not only extends your keyboard, monitor and mouse, but

also serial port, audio speakers and microphone on a single CAT 5 UTP cable, with satisfying video quality

and audio output.

K5EXT300 comprises two disparate units - K5LC and K5CMLC. K5LC is the local console unit, i.e., the

receiver on one end of the UTP cable. K5CMLC is the computer module with local console, i.e. the

transmitter on the other end of the UTP cable. However, K5CMLC also provides a local console, so that

users can also access the computer at the local end, in addition to the remote end on K5LC.

The firmware can be upgraded whenever is needed to enhance compatibility or functionality. For the flash

upgrade procedure, please refer to the Flash Upgrade Operation Guide provided with the new version of

firmware upgrade file.

K5CMLC – Computer Module w/ Local Console

K5LC – Local Console

Package Contents

Please check whether you have all the following items within the packaging box:

;K5CMLC (Computer Module w/ Local Console – Console 1) x 1

;K5LC (Remote Console – Console 2) x 1

;Slim 3-in-1 PS/2 KVM Cable x 1

;USB Cable (TypeA - TypeB) x 1

;Audio & Mic Combo Cable x 1

;Power Adapters (DC9V 1.7A) x 2

;This Quick Installation Guide x 1

;The User Guide (electronic version, found only within the Support CDROM)

;Support CDROM x 1

KEXT300 User Manual Rev 1.3

- -

Front-panel and Rear Panel Views

The back panels are where the various connectors are located on the two pieces of K5EXT300. Before you

connect these two units to any computer, cabling or peripherals, you should get a glimpse of the main

connectors you are going to encounter when setting up the system

K5LC – Remote Console Unit (300m away from computer)

K5LC - Backpanel

1. Power receptacle (DC9V 1A)

2. USB port [only for firmware upgrade use]

3. RS-232 port for serial extension

4. Monitor port [HDB15]

5. PS/2 keyboard port

6. PS/2 mouse port

7. USB mouse port

8. USB keyboard port

9. Audio receptacle

10. Mic receptacle

11. CAT5 Extension Port [RJ-45, connect to a CAT5 UTP cable, 300m max.]

K5CMLC – Computer Module with Local Console (Connected to the computer)

K5CMCL - Backpanel

[Computer Connections]

a. Power receptacle (DC9V 1A)

b. RS-232 port for serial extension

c. PC/KVM port for computer connection (integrated with keyboard, mouse and video interface)

d. Audio output port

e. Mic input port

f. USB interface for computer connection [for USB keyboard and mouse connection]

[Console Connections]

g. Monitor port [HDB15]

h. PS/2 mouse port

i. PS/2 keyboard port

j. USB mouse port

k. USB keyboard port

l. Audio receptacle

m. Mic receptacle

n. CAT5 Extension Port [RJ-45, connect to a CAT5 UTP cable, 300m max.]

KEXT300 User Manual Rev 1.3

- -

Installing the Extender

Before you install the two pieces of K5EXT300, you should have these items on the

checklist ready:

1. The computer for extension should be one with either PS/2 or USB interfaces.

2. You should check the display mode of the computer to be within 1600 x 1200 pixel dimension. And

refresh rate to be one that is more commonly used such as 60Hz, etc.

3. Since the CAT5 KVM extender supports only standard 5-key mouse and keyboard, any more advanced

mouse/keyboard function will not be supported by CAT5 extension.

4. Use good quality UTP cable (max. 300m/1000ft). Note that good quality cable will give better video

outcome with longer distance span.

5. Any cabling distance longer than 300m/1000ft will experience more signal degradation with longer span.

However, good quality cable can reach out farer away.

6. The choice of path of the CAT5 UTP cable should not only take into account the shortest possible path,

but also one that is relatively farer away from any significant electromagnetic interference source.

7. Prepare one or two sets of keyboard, mouse, monitor, mic and speakers - one set for console 1 and the

other set for console 2.

8. There should be power outlets near where you locate the extenders.

Plan the layout path and deploy the UTP cable for extension

Step 1. Plan the path through which the UTP cable will be deployed across the distance between the K5LC

and K5CMLC. You should choose the layout path not only base on shortest possible length

consideration, but also on least electromagnetic interference.

Step 2. Lay out the UTP cable according to your planned path.

KEXT300 User Manual Rev 1.3

- -

Configure the K5CMLC (Local)

Step 3. Connect one end of the UTP cable to the CAT5 Extension port of the K5CMLC. (Connector n)

Step 4. Connect the power adapter to the K5CMLC to power it up before connecting any computer or cables

to it. (connector a)

Step 5. Connect the K5CMLC to the computer, using the Slim 3-in-1 PS/2 KVM cable (connector c) and/or

the USB cable (connector f). (Note that if you need to connect with the USB interface, you should

connect the USB cable to the computer since the Slim 3-in-1 PS/2 KVM cable supports only the

PS/2 interface.)

Step 6. Set up Console 1: Connect a set of keyboard, mouse, monitor as well as a set of speakers and

microphone to the K5CMLC Console ports (connectors g, h, I, I, k, l, m).

Step 7. Power on the computer, and check the keyboard, mouse, video and audio output and mic input on

Local Console 1 to see if it works fine. If should work fine before you proceed to next steps.

Configure the K5LC (Console2)

Step 8. Connect the other end of the UTP cable to the CAT5 Extension port of the K5LC (connector 11).

Step 9. Connect the power adapter to the K5LC (connector 1) to power it up before connecting any devices

to it.

Step 10. Set up Console 2: Connect a set of keyboard, mouse, monitor (connector 4, 5, 6, 7, 8) as well as a

set of speakers and microphone (connector 9, 10) to the K5LC Console ports. If serial extension is

used, you may also connect a serial device to the serial port (connector 3).

Step 11. Check the keyboard, mouse, video, audio output and mic input on the Local Console 2 to see if it

works fine. At this time, the video might be blurred since it is not yet adjusted and optimized.

Step 12. Adjust the video parameters to optimize the display output (Refer to OSD Menu/Video page for

details).

KEXT300 User Manual Rev 1.3

- -

Using the OSD Menu

The CAT5 KVM Extender provides intuitive OSD Menus facilitate control and setup operations. Users can

set up the video, audio, serial extensions as well as password protection, auto logout, etc.

To open the OSD Menu, hit the following keyboard hotkeys:

Hotkey sequence = [ScrLk]*+ [ScrLk] * + Space

* User-configurable from among SCROLL LOCK, CAPS, ESC, F12 or NUM LOCK

Changing the Hotkeys

The hotkey is default to ScrLk + ScrLk. To change the hotkeys go to the OSD System page and select any

one of the five alternatives - SCROLL LOCK, CAPS, ESC, F12 or NUM LOCK.

Each keystroke within a hotkey sequence should be pressed within 2 seconds. Otherwise, the hotkey

sequence will not be validated.

Navigating into the OSD Menu

Esc: Exit,

ÅÆLeft/Right cursor: change value in the menu option

ÇÈUp/Down Cursor: Select the option item.

F1: go to Main Menu

F9: Logout the OSD Menu (However, if the password protection is not enabled, the Logout feature

will not be available

TAB: Go to the next setting page.

These keys are listed explicitly on every OSD setting page for your ready reference.

OSD Menu/Main page

This is the Main Menu of the OSD Menu Control and it is also the first page you will see when you hit the

keyboard hotkeys - Scrlk + Scrlk + Space - to open the OSD Menu. From the Main Menu, you can go to

the Video Page, Status Page, Serial page and System page. Highlight the page name and hit <Enter>.

KEXT300 User Manual Rev 1.3

- -

OSD Menu/Video Page

The Video page allows you to adjust the video parameters such as brightness, sharpness, Red Delay and

Green Delay. The ranges of adjustment of these parameters are

Brightness: 0 ~ 64

Sharpness: 0 ~ 64

Red Delay/Blue: -31 ~ +31

Green Delay/Blue: -31 ~ +31

In order to achieve optimized video output on the remote console (K5LC), you must adjust these four

parameters. For details, please refer to next section, Optimize the Video Display on the Remote Console.

OSD Menu/Audio Page

The Audio page allows you to toggle the audio ON/OFF, and to adjust the volume of the sound output on the

K5LC unit.

Audio: toggle On/Off the sound output on the remote console.

Volume: adjust sound volume output on the remote console

To achieve an optimized audio output on the remote console, you might need to adhere to the following

guideline:

1. Adjust the computer volume the highest level that does not saturate K5CMLC input

To do that, play some good music on the computer and hear it from K5LC. Starting from zero, increase

the computer volume. As soon as saturation appears (this distortion phenomenon is very easy to notice),

diminish slightly the computer level. This will give the audio signal the best amplitude for digitalization.

If the volume output is too small, adjusting the volume on K5LC will not help to give good sound

amplitude.

2. Adjust the sound volume output on K5LC at you convenience

Use the slide bar on the OSD menu (Audio page/ Volume) or hot keys: Scrlk + Scrlk + ↑and Scrlk +

Scrlk + ↓

KEXT300 User Manual Rev 1.3

- -

OSD Menu/Status Page

The Status page displays the firmware versioning information of the K5LC and the K5CMLC. The

versioning number is actually a date code, which has the form of DDMMYY.

OSD Menu/Serial Page

The Serial page allows you to set up the serial connection extension. It must correspond to the computer

settings. You must configure the baud rate, the number of data bits, the parity type, the stop bit width and the

flow control method.

The ranges of adjustment of these parameters are

Baud Rate: 300, 1200, 2400, 4800, 9600, 19200

Data bits: 5, 6, 7, 8

Parity: None, Odd, Even

Stop bits: 1, 2

Flow Control: None, Hardware, Xon/Xoff

Table des matières

Autres manuels ProSum Extenseur

ProSum

ProSum KLEv3 Manuel utilisateur

Manuels Extenseur populaires d'autres marques

SY HDBT-60T Manuel utilisateur

Appsys ProAudio

Appsys ProAudio ADX-16 Manuel utilisateur

Atlona

Atlona RS232 Manuel utilisateur

IDK

IDK OPF-TH1000-A Manuel utilisateur

Enable-IT

Enable-IT 824WP Manuel utilisateur

Worx

Worx Landroid RadioLink WA0864 Fiche technique

TP-Link

TP-Link TL-WA730RE Manuel utilisateur

Camplex

Camplex CMX-HDMI-SFPL Manuel utilisateur

SC&T

SC&T HE03-4K Manuel utilisateur

Marmitek

Marmitek MegaView70 Manuel utilisateur

Samsung

Samsung SCS-26UC4 Manuel utilisateur

Foxun

Foxun SX-GES24 Manuel utilisateur

MuxLab

MuxLab 500771 Manuel utilisateur

foxunhd

foxunhd SX-AEX01 Manuel utilisateur

TERK Technologies

TERK Technologies LFIRX2 Manuel utilisateur

Devolo

Devolo Audio Extender Manuel

Edimax

Edimax EW-7438RPn V2 Manuel utilisateur

Shinybow USA

Shinybow USA SB-6335T5 Manuel utilisateur