PROPOINT 8681330 Manuel utilisateur
V1.0 8681330
Please read and understand all instructions before use. Retain this
manual for future reference.
USER MANUAL
10,000W CONSTRUCTION
HEATER
WITH ENCLOSED MOTOR
8681330 10,000W CONSTRUCTION HEATER V1.0
WITH ENCLOSED MOTOR
2 For technical questions call 1-800-665-8685
SPECIFICATIONS
Type Electric Unit Heater
BTU Rating 34,100
Heat Settings 10,000W
Voltage Rating
240V
Current Rating 42A
Air Consumption 265 CFM
INTRODUCTION
Uses a steel-sheathed tubular heating element. Features an
adjustable thermostat and overheat protection.
SAFETY
WARNING! Read and understand all instructions before using
this tool. The operator must follow basic precautions to reduce
the risk of personal injury and/or damage to the equipment.
Keep this manual for safety warnings, precautions, operating or
inspection and maintenance instructions.
HAZARD DEFINITIONS
Please familiarize yourself with the hazard notices found in this
manual. A notice is an alert that there is a possibility of property
damage, injury or death if certain instructions are not followed.
10,000W CONSTRUCTION
HEATER
WITH ENCLOSED MOTOR
V1.0 10,000W CONSTRUCTION HEATER 8681330
WITH ENCLOSED MOTOR
Visit www.princessauto.com for more information 3
DANGER! This notice indicates an immediate and specific
hazard that will result in severe personal injury or death if the
proper precautions are not taken.
WARNING! This notice indicates a specific hazard or unsafe
practice that could result in severe personal injury or death if
the proper precautions are not taken.
CAUTION! This notice indicates a potentially hazardous
situation that may result in minor or moderate injury if proper
practices are not taken.
NOTICE! This notice indicates that a specific hazard or unsafe
practice will result in equipment or property damage, but not
personal injury.
WORK AREA
1. Operate in a safe work environment. Keep your work area
clean, well-lit and free of distractions.
2. Keep anyone not wearing the appropriate safety
equipment away from the work area.
3. Store tools properly in a safe and dry location. Keep tools
out of the reach of children.
4. Do not install or use in the presence of flammable gases,
dust or liquids.
PERSONAL SAFETY
WARNING! Wear personal protective equipment approved by
the Canadian Standards Association (CSA) or American
National Standards Institute (ANSI).
PERSONAL PROTECTIVE EQUIPMENT
1. Always wear impact safety goggles that provide front and
side protection for the eyes. Eye protection equipment
should comply with CSA Z94.3-07 or ANSI Z87.1 standards
based on the type of work performed.
8681330 10,000W CONSTRUCTION HEATER V1.0
WITH ENCLOSED MOTOR
4 For technical questions call 1-800-665-8685
2. Wear gloves that provide protection based on the work
materials or to reduce the effects of tool vibration.
3. Wear protective clothing designed for the work
environment and tool.
4. Non-skid footwear is recommended to maintain footing
and balance in the work environment.
PERSONAL PRECAUTIONS
Control the tool, personal movement and the work
environment to avoid personal injury or damage to the tool.
1. Do not operate any tool when tired or under the influence
of drugs, alcohol or medications.
2. Avoid wearing clothes or jewelry that can become
entangled with the moving parts of a tool. Keep long hair
covered or bound.
3. Do not overreach when operating the tool. Proper footing
and balance enables better control in unexpected situations.
SPECIFIC SAFETY PRECAUTIONS
WARNING! DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence to the
tool safety rules. If you use this tool unsafely or incorrectly,
you can suffer serious personal injury.
1. Use the correct tool for the job. This tool was designed for
a specific function. Do not modify or alter this tool or use it
for an unintended purpose.
2. This heater is for indoor use only.
3. Do not use the heater in areas with corrosive atmospheres
(marine, greenhouses, or chemical storage rooms). Do not
use in locations where flammable liquids are used or stored.
4. Do not move, handle or service the heater while it is hot.
V1.0 10,000W CONSTRUCTION HEATER 8681330
WITH ENCLOSED MOTOR
Visit www.princessauto.com for more information 5
5. Keep all combustible materials away from a running heater.
Refer to the table below for the minimum clearance around
the heater:
Sides 1 ft (0.30 m)
Back
0.6 ft (0.18 m)
Floor 8 ft (2.4 m)
Furniture and Other
Combustible Materials
3 ft (0.91 m)
6. Do not block the heater’s air intakes or exhaust.
7. Do not insert or allow foreign objects to enter through the
heater’s ventilation.
8. Direct the heater’s airflow parallel to or away from an
adjacent wall.
9. Turn the unit off immediately and resolve any issues if the
Overheating Indicator light is flashing.
10. Keep small pets away from the area during first use. The
unit will initially produce fumes as the manufacturer’s
coatings are burned off. The fumes are harmless to humans
but may affect small animals.
ELECTRICAL SAFETY
WARNING! Do not touch or handle a live tool with any part of
your body that is wet or damp. Wet skin reduces resistance to
electrical current, increasing the danger of a serious or
fatal shock.
1. Disconnect tool from power source before cleaning,
servicing, changing parts/accessories or when not in use.
2. Protect yourself against electric shocks when working on
electrical equipment. Avoid body contact with grounded
surfaces. There is an increased chance of electrical shock if
your body is grounded.
8681330 10,000W CONSTRUCTION HEATER V1.0
WITH ENCLOSED MOTOR
6 For technical questions call 1-800-665-8685
3. Do not expose the tool to rain or wet conditions. Water
entering a power tool will increase the risk of
electric shock.
4. Do not alter any parts of the tool or accessories. All parts
and accessories are designed with built-in safety features
that may be compromised if altered.
5. Make certain the power source conforms to requirements
of your equipment (see Specifications).
6. When wiring an electrically driven device, follow all
electrical and safety codes, as well as the most recent
Canadian Electrical Code (CE) and Canadian Centre for
Occupational Health and Safety (CCOHS).
WARNING! All wiring should be performed by a
qualified electrician.
UNPACKING
WARNING! Do not operate the tool if any part is missing.
Replace the missing part before operating. Failure to do so
could result in a malfunction and personal injury.
Remove the parts and accessories from the packaging and inspect
for damage.
ASSEMBLY & INSTALLATION
Dashed numbers in parenthesis (Fig. 1-1) refer to a specific
point in an illustration or image.
POSITIONING THE HEATER
Install the heater out of traffic areas and maintain the minimum
clearance required. The direction of the airflow should not be
restricted or obstructed. If installing multiple heaters, ensure
that the units are arranged to promote proper air circulation.
V1.0 10,000W CONSTRUCTION HEATER 8681330
WITH ENCLOSED MOTOR
Visit www.princessauto.com for more information 7
MOUNTING THE BRACKET
CAUTION! The mounting structure and the anchoring
hardware must be able to support the weight of the heater to
avoid hazardous situations.
1. Locate a stud in the ceiling or
wall joist.
2. Remove the mounting bracket
from the heating unit.
2.1 Loosen the bracket screws
with a wrench.
2.2 Slip the handle off the
screw heads.
3. Mount the bracket to the ceiling or wall joist using the
provided 3/8 in. diagonal lag bolts and flat washers. See
Fig. 2. Use only one bolt and washer set on the centre of
the bracket if the heater will be rotated.
HANGING THE HEATER
1. Lift the heater up and into the mounting bracket.
2. Align the bracket screws with the keyhole slots. Use the
bottom keyhole slot (Fig. 3-1) if the heater will be tilted down.
3. Tighten the bracket screws to secure.
Fig. 1
Fig. 2
8681330 10,000W CONSTRUCTION HEATER V1.0
WITH ENCLOSED MOTOR
8 For technical questions call 1-800-665-8685
WIRING THE HEATER
WARNING! Switch off the appropriate circuit breakers at the
electrical panel before starting to avoid electrical shock.
CAUTION! Use only copper wires that are rated for at least 75 ºC.
1. Slide the copper wires (see table below for wiring
requirements) through the provided cable connectors.
VOLTAGE RATING
CURRENT
RATING
MAX.
FUSE SIZE
MIN. WIRE
SIZE
Single phase
10KW @ 240V
41 60 #6
Three-phase
10KW @ 240V
26 38 #10
IMPORTANT! A conduit may be required for certain
setups. Check with your local electrical codes.
2. Remove the front screws (Fig. 3-2) at the base of the
heater to access the power block.
Fig. 3
Fig. 4
V1.0 10,000W CONSTRUCTION HEATER 8681330
WITH ENCLOSED MOTOR
Visit www.princessauto.com for more information 9
3. Connect the wires to the power block by following the
diagram below:
Fig. 5
CONVERTING FROM SINGLE PHASE TO
THREE-PHASE
The unit is factory-wired for single phase applications. To
convert for three-phase applications, connect L1 and L3 (see
Fig. 6) to L2 (see Fig. 7).
Fig. 6
8681330 10,000W CONSTRUCTION HEATER V1.0
WITH ENCLOSED MOTOR
10 For technical questions call 1-800-665-8685
Fig. 9
Fig. 7
Fig. 8
CONNECTING AN EXTERNAL THERMOSTAT
Connect the external thermostat to the switch in the control
panel as shown in Fig. 8.
OPERATION
IDENTIFICATION KEY
A. Power Indicator (Yellow)
B. Overheating Indicator (Red)
C. Thermostat
D. Switch
SETTING THE THERMOSTAT
Use the switch to toggle between the heater’s thermostat and an
external thermostat (if installed). To use the heater’s thermostat:
1. Rotate the thermostat knob clockwise to HIGH. The power
indicator will turn yellow.
Table des matières
Langues :
Autres manuels PROPOINT Chauffage
Manuels Chauffage populaires d'autres marques
oventrop
oventrop Regucor Series Manuel utilisateur
Blaze King
Blaze King CLARITY CL2118.IPI.1 Manuel utilisateur
ELMEKO
ELMEKO ML 150 Manuel utilisateur
BN Thermic
BN Thermic 830T Manuel utilisateur
KING
KING K Series Mode d’emploi
Empire Comfort Systems
Empire Comfort Systems RH-50-5 Guide de démarrage rapide
Empire Heating Systems
Empire Heating Systems WCC65 Manuel utilisateur
Wetekom
Wetekom 92 86 43 Manuel utilisateur
Desa
Desa SPC170-F Manuel utilisateur
Watlow
Watlow Watrod Electric Tubular Heaters Manuel utilisateur
Haverland
Haverland ECO-DRY GPS Series Manuel de la liste des pièces
Stelpro
Stelpro ASILVC2060 Series Manuel utilisateur