The lock operates when applying and interrup
switch (button). Controller installation is
power of the lock is supplied by the voltage from 11 to 14 V of the direct current.
Connect the power cable of the
red – positive, black – negative.
(The reverse polarity voltage supply
Provide reliable electrical contact. I
solate the connection points to avoid short
ATENTION!!! The possibility to use
on the level of premise accountability, assignment of access restriction
The lock does not fix the
roller (the door does not fix when it is
The door does not close fully,
roller does not enter, or
it enters with friction into the lock
When the status of the door is
tighter to the door frame.
8. MAINTENANCE
Maintenance of a lock is performed at
- Examination of the lock to check
9. MANUFACTURER'S WARRANTY
Engineering & Technical Center PROMIX, LLC guarantees the conformity of
requirements of applicable TU standards under the regulation
The warranty period is 18 months commencing from the date of acceptance by Quality Control Department.
Within the warranty period, Engineering & Technical Center PROMIX, LLC undertakes to re
charge. The shipping cost to the place of repair and back shall be borne by the Buyer.
The warranty shall not cover defects or damages, resulting from:
- improper maintenance by the Buyer;
- using the lock in conditions
that do not conform to the operating requirements;
violation of transportation and storage regulations.
Electromechanical lock "Sheriff-5"
with the specified date of manufacture is made and accepted in accordance with TU
, obligatory requirements of state standards and applicable technical documents, found fit for service and
packed by Engineering & Technical Center PROMI
Engineering & Technical Center PROMIX, LLC
Russia, 214030, Smolensk city,
Tel. (4812) 619-330
www.itc-promix.ru
Please send us all your comments and
suggestions concerning our lock via e
The lock operates when applying and interrup
ting the power supply, and for it
is usually used a controller (contro
ing to the technical data sheet.
power of the lock is supplied by the voltage from 11 to 14 V of the direct current.
not provide operability of the lock, but does not
solate the connection points to avoid short
this lock to restrict access to premises is
on the level of premise accountability, assignment of access restriction
and other factors (security,
roller (the door does not fix when it is
n the "closed" status (turn on the voltage supply of the lock).
Check the polarity and make sure that the
voltage supply corresponds with the
Make sure that when drilling the hole for the lock, the internal metal frame of
the door profile was drilled either.
Adjust the deadbolt (see Para
. 6.2) in that way when the door is closed the
into the lock groove until the full operation of the fixation device.
It is possible that the fixation device manually one
moves to the "close" position (not by the
manually or by an external object). Change the
fixation device position to "open", for this turn off the
voltage supply of the lock, and turn the fixation
roller does not enter, or
it enters with friction into the lock
establish the door position one changed during operation. If it is impossible
to re-establish it, adjust the deadbolt (see Para
When the status of the door is
Eliminate the causes of loose fit of the door to the door frame. Adjust the
deadbolt in the horizontal direction.
once per two months and includes:
reliability. If it is necessary, tighten up
fixing elements of the lock and the
. If it is necessary, adjust the position of the
Engineering & Technical Center PROMIX, LLC guarantees the conformity of
lectromechanical lock "Sheriff
requirements of applicable TU standards under the regulation
s of operation and installation
established in this operating manual.
The warranty period is 18 months commencing from the date of acceptance by Quality Control Department.
Within the warranty period, Engineering & Technical Center PROMIX, LLC undertakes to re
charge. The shipping cost to the place of repair and back shall be borne by the Buyer.
The warranty shall not cover defects or damages, resulting from:
that do not conform to the operating requirements;
violation of transportation and storage regulations.
AND ACCEPTANCE CERTIFICATE
with the specified date of manufacture is made and accepted in accordance with TU
, obligatory requirements of state standards and applicable technical documents, found fit for service and
packed by Engineering & Technical Center PROMI
Engineering & Technical Center PROMIX, LLC
suggestions concerning our lock via e
is usually used a controller (contro
power of the lock is supplied by the voltage from 11 to 14 V of the direct current.
and other factors (security,
n the "closed" status (turn on the voltage supply of the lock).
voltage supply corresponds with the
Make sure that when drilling the hole for the lock, the internal metal frame of
. 6.2) in that way when the door is closed the
into the lock groove until the full operation of the fixation device.
It is possible that the fixation device manually one
moves to the "close" position (not by the
manually or by an external object). Change the
fixation device position to "open", for this turn off the
voltage supply of the lock, and turn the fixation
establish the door position one changed during operation. If it is impossible
Eliminate the causes of loose fit of the door to the door frame. Adjust the
fixing elements of the lock and the
lectromechanical lock "Sheriff
established in this operating manual.
The warranty period is 18 months commencing from the date of acceptance by Quality Control Department.
Within the warranty period, Engineering & Technical Center PROMIX, LLC undertakes to re
pair the defective product free of
with the specified date of manufacture is made and accepted in accordance with TU
, obligatory requirements of state standards and applicable technical documents, found fit for service and
