ProLights KAPPAPIX 26B1X1BF Manuel utilisateur
USER MANUAL
English version
KAPPAPIX 26B1X1BF
XR LED wall module, SMD1515 BF, p2.6,
1200nit, 50x50, 7680Hz, Brompton, 6,3 kg
REV.01-07/23
Thank you for choosing PROLIGHTS
Please note that every PROLIGHTS product has been designed in Italy to meet quality and performance requirements
for professionals and designed and manufactured for the use and application as shown in this document.
Any other use, if not expressly indicated, could compromise the good condition/operation of the product and/or be
a source of danger.
This product is meant for professional use. Therefore, commercial use of this equipment is subject to the respectively
applicable national accident prevention rules and regulations.
Features, specications and appearance are subject to change without notice. Music & Lights S.r.l. and all afliated
companies disclaim liability for any injury, damage, direct or indirect loss, consequential or economic loss or any other
loss occasioned by the use of, inability to use or reliance on the information contained in this document.
Product user manual can be downloaded from the website www.prolights.it , or can be inquired to the ofcial
PROLIGHTS distributors of your territory (https://www.prolights.it/sales_network.html).
Scanning the below QR Code, you will access the download area of the product page, where you can nd a broad
set of always updated technical documentation: specications, user manual, technical drawings, photometrics,
personalities, xture rmware updates.
The PROLIGHTS Logo, PROLIGHTS names and all other trademark in this document pertaining to PROLIGHTS services
or PROLIGHTS product are trademarks OWNED or licensed by Music & Lights S.r.l., its afliates, and subsidiaries.
PROLIGHTS is a registered trademark by Music & Lights S.r.l. All right reserved. Music & Lights – Via A. Olivetti, snc -
04026 - Minturno (LT) ITALY.
Visit the download area
of the product page
PROLIGHTS - KAPPAPIX 26B1X1BF 01
INDEX
SAFETY INFORMATION 02
1 - OPTIONAL ACCESSORIES 4
2 - TECHNICAL DRAWING 5
3 - PRODUCT OVERVIEW 6
4 - INSTALLATION 7
GROUND BAR STACKING SYSTEM................................................................................. 7
FLY BAR HANGING SYSTEM.......................................................................................... 11
6 - CONNECTION TO THE MAINS SUPPLY 14
7 - START UP 14
CONNECT AND DISCONNECT POWER FROM THE PRODUCT.................................. 14
8 - DATA CONNECTION 15
DATA CABLING .............................................................................................................. 15
MAIN AND BACKUP DATA LINE.................................................................................... 15
9 - MAINTENANCE 17
MAINTENANCE AND CLEANING THE PRODUCT........................................................ 17
MAINTENANCE ON INDOOR PRODUCT ..................................................................... 17
MAINTENANCE ON OUTDOOR PRODUCT ................................................................. 18
CORRECT STARTUP/SHUTDOWN SEQUENCE............................................................. 18
TRANSPORTATION AND STORAGE.............................................................................. 18
GENERAL INDICATIONS FOR USE................................................................................ 19
TROUBLESHOOTING..................................................................................................... 20
PROLIGHTS - KAPPAPIX 26B1X1BF02
SAFETY INFORMATION
WARNING!
• See https://www.prolights.it/product/KAPPAX26B1X1BF#download for installation
instructions.
• Please read carefully the instruction reported in this section before installing, powering,
operating or servicing the product and observe the indications also for its future handling.
This unit is not for household and residential use, only professional applications.
Connection to mains supply
• The Connection to the mains supply must be carried out by a qualied electrical
installer.
• Use only AC supplies 100-240V 50-60 Hz, the xture must be electrically connected
to ground (earth).
• Select the cable cross section in according with the maximum current draw of the
product and the possible number of products connected at the same power line.
• The AC mains power distribution circuit must be equipped with magnetic+residual
current circuit breaker protection.
• Do not connect it to a dimmer system; doing so may damage the product.
Protection and Warning against electrical shock
• Do not remove any cover from the product, always disconnect the product from AC
power before servicing.
• Ensure that the xture is electrically connected to ground (earth). And use only a
source of AC power that complies with local building and electrical codes and has
both overload and ground-fault (earth-fault) protection.
• Before using the xture, check that all power distribution equipment and cables are
in perfect condition and rated for the current requirements of all connected devices.
• Isolate the xture from power immediately if the power plug or any seal, cover, ca-
ble, or other components are damaged, defective, deformed or showing signs of
overheating.
• Do not reapply power until repairs have been completed.
• Refer any service operation not described in this manual to PROLIGHTS Service team
or an authorized PROLIGHTS service center.
Installation
• Make sure that all visible parts of the product are in good visible condition before its
use or installation.
• Make sure the point of anchorage is stable before positioning the projector.
• When suspending the xture above ground level, secure it against failure of primary
attachments by attaching a safety cable that is approved as a safety attachment for
the weight of the xture to the attachment point on the main frame of the product. ln
case the safety cable, enter in action, it needs to be replaced with a new one.
• Install the product only in well ventilated places.
• For non temporary installations, ensure that the xture is securely fastened to a load-
bearing surface with suitable corrosionresistant hardware.
• For a temporary installation with clamps, ensure that the quarter-turn fastener and/or
screws are turned fully, and secured with a suitable safety cable.
PROLIGHTS - KAPPAPIX 26B1X1BF 03
Protection from burns and re
• The exterior of the xture becomes hot during use. Avoid contact by persons and
materials.
• Ensure that there is free and unobstructed airow around the xture.
• Keep ammable materials well away from the xture.
• Do not expose the front glass to sunlight or any other strong light source from any an-
gle. Lenses can focus the sun’s rays inside the xture, creating a potential re hazard.
• Do not attempt to bypass thermostatic switches or fuses.
Indoor use
• This product is designed for indoor and dry environments.
• Do not use in wet location and do not expose the xture to rain or moisture.
• Never use the xture in places subject to vibrations or bumps.
• Make certain that no inammable liquids, water or metal objects enter the xture.
• Excessive dust, smoke uid, and particle build up degrades performance, causes
overheating and will damage the xture.
• Damages caused by inadequate cleaning or maintenance are not covered by the
product warranty.
Maintenance
• Warning! Disconnect the xture from AC mains power and allow to cool for at least
10 minutes before handling.
• Only technicians who are authorized by PROLIGHTS or Authorised service partners
are permitted to open the xture.
• Users may carry out external cleaning, following the warnings and instructions pro-
vided, but any service operation not described in this manual must be referred to a
qualied service technician.
• Important! Excessive dust, smoke uid, and particle build up degrades performance,
causes overheating and will damage the xture. Damages caused by inadequate
cleaning or maintenance is not covered by the product warranty.
Disposal
• This product is supplied in compliance with European Directive 2012/19/EU – Waste
Electrical and Electronic Equipment (WEEE). To preserve the environment please dis-
pose/ recycle this product at the end of its life according to the local regulation.
The products to which this manual refers comply with:
• 2014/35/EU - Safety of electrical equipment supplied at low voltage (LVD).
• 2014/30/EU - Electromagnetic Compatibility (EMC).
• 2011/65/EU - Restriction of the use of certain hazardous substances (RoHS).
Other approvals
PROLIGHTS - KAPPAPIX 26B1X1BF4
1 - OPTIONAL ACCESSORIES
• KXFCM80261X1 Flightcase 8 in1 for KAPPAX26B1X1BF
• KSXHGB01 Fly bar / ground bar for SIGMAX and KAPPAX systems, 1 column
• KSXHGB02 Fly bar / ground bar for SIGMAX and KAPPAX systems, 2 columns
• KSXCJB Ground system back horizontal support for SIGMAX and KAPPAX series LED wall
• KSXBS21 2in1 back support for GAMMAX series LED wall for ground system xing
• KSXBS31 3in1 back support for GAMMAX series LED wall for ground system xing
• KSXBSC Back plate for GAMMAX series LED wall for ground system xing
• KSXGHR Ground system back horizontal reinforcement for SIGMAX & KAPPAX series LED wall
• KXXJ Metal joint used to connect 4 pcs KAPPAX series cabinets
• KXCJ80 Cabinet curve plate concave for KAPPAX series cabinets, 10°
• KXCJ81 Cabinet curve plate concave for KAPPAX series cabinets, 9°
• KXCJ82 Cabinet curve plate concave for KAPPAX series cabinets, 8°
• KXCJ825 Cabinet curve plate concave for KAPPAX series cabinets, 7,5°
• KXCJ83 Cabinet curve plate concave for KAPPAX series cabinets, 7°
• KXCJ84 Cabinet curve plate concave for KAPPAX series cabinets, 6°
• KXCJ85 Cabinet curve plate concave for KAPPAX series cabinets, 5°
• KXCJ86 Cabinet curve plate concave for KAPPAX series cabinets, 4°
• KXCJ87 Cabinet curve plate concave for KAPPAX series cabinets, 3°
• KXCJ875 Cabinet curve plate concave for KAPPAX series cabinets, 2,5°
• KXCJ88 Cabinet curve plate concave for KAPPAX series cabinets, 2°
• KXCJ89 Cabinet curve plate concave for KAPPAX series cabinets, 1°
• KXCJ90 Cabinet curve plate standard for KAPPAX series cabinets, at 0°
• KXCJ91 Cabinet curve plate convex for KAPPAX series cabinets, 1°
• KXCJ92 Cabinet curve plate convex for KAPPAX series cabinets, 2°
• KXCJ925 Cabinet curve plate convex for KAPPAX series cabinets, 2,5°
• KXCJ93 Cabinet curve plate convex for KAPPAX series cabinets, 3°
• KXCJ94 Cabinet curve plate convex for KAPPAX series cabinets, 4°
• KXCJ95 Cabinet curve plate convex for KAPPAX series cabinets, 5°
• OXFCIS100 Rigging/ground-stack structure ightcase OMEGAX-DELTAX LED-display, 100cm
• OXFCIS200 Rigging/ground-stack structure ightcase OMEGAX-DELTAX LED-display, 200cm
• OXFCSP Spare part ightcase for OMEGAX-DELTAX series LED-display
• KXACL01 Power cable for KAPPAX LED display series, L 140 cm
• KXACL10 Power cable for KAPPAX LED display series, L 10 m
• KXDCL01 Data cable for KAPPAX LED display series assembled with RJ45, L 140 cm
• KXDCL10 Data cable for KAPPAX LED display series assembled with RJ45, L 10 m
• BROSX40 BROMPTON 4K LED video processor
• BROXD10G BROMPTON data distribution unit
• FMTOOL Front maintenance tool for OMEGAX-DELTAX series LED screens (INDOOR)
• MRTOOL Mask Replacement TOOL for OMEGAX26B and OMEGAX26BE
PROLIGHTS - KAPPAPIX 26B1X1BF 5
500 mm
[19.7 in]
500 mm
[19.7 in]
91 mm
[3.6 in]
Fig. 01
Weight: 6,3 kg - 13,89 lbs
2 - TECHNICAL DRAWING
PROLIGHTS - KAPPAPIX 26B1X1BF6
3 - PRODUCT OVERVIEW
1. MODULE: single LED display module that makes up the cabinet with magnetic attachment
2. SIDE LOCK MECHANICS: Side Panel locking and unlocking mechanism.
3. UPPER LOCK MECHANICS: Upper Panel locking and unlocking mechanism.
4. SIGNAL CONNECTORS: Ethernet connectors for sending and receiving Data Information from the
controller.
5. POWER BOX LOCK: handle to release power box
6. POSITIONING PIN: allows to center and hook cabinet easier.
7. MOUNTING HOLE: to be used to x the cabinets together using a metal plate
8. AUTOMATIC CORNER PROTECTION: automatic corner protection system with lock
9. CABINET HANDLE: handy handles for easy assembly.
10. LOCKING TAB: to hook cabinet to underside.
11. POWER IN CONNECTOR: for connection to the Mains 100-240V~/50-60Hz.
12. POWER OUT CONNECTOR: power output for connection of multiple units in series
13. MECHANICAL CORNER PIN: mechanical corner protection closing
14. ANGLE MECHANICS: allow both concave and convex precise installation of +10° / -10°
Fig 02
1
26
4
12
11 10 14
37
9
4
5
13
8
PROLIGHTS - KAPPAPIX 26B1X1BF 7
Remove highlighted pins on the KSXHGB01 accessory for grounding applications.
If you use the KSXHGB02 accessory, remove highlighted pins for grounding applications.
Align the KSXHGB y/ground bar accessories, then adjust the height of the feet toward the ground
to keep the ground beam perfectly horizontal.
4 - INSTALLATION
GROUND BAR STACKING SYSTEM
Fig 03
PROLIGHTS - KAPPAPIX 26B1X1BF8
Fig 04
Insert the KSXCJB accessory into the prepared slot in the KSXHGB, then lock it using the lever by
turning it following the closed padlock icon. after which align with respect to the horizontal plane
also the horizontal support if necessary by helping with a hexagonal wrench.
Hook the cabinet to the ground bar, taking care to align the holes in the screen with the pins in
the bar.
Hook the panels sideways and lock them by push and turning the locking lever.
Table des matières
Autres manuels ProLights Moniteur
