Project Source 19551-000 Manuel utilisateur
1
ATTACH YOUR RECEIPT HERE
Serial Number______________________ Purchase Date____________________________
Questions, problems, missing parts? Before returning to your retailer, call our customer
service department at 1-866-389-8827, 8 a.m. - 6 p.m., EST, Monday - Thursday,
8 a.m. - 5 p.m., EST, Friday.
Lowes.com
AB1549
Français p. 9
Español p. 17
2
PACKAGE CONTENTS
PART DESCRIPTION QUANTITY
A Track Mounting Screw (preassembled to mounting plate (B)) 2
B Mounting Plate 1
C Power Supply (preassembled to mounting plate (B)) 1
D Canopy (preassembled to mounting plate (B)) 1
E Canopy Screw (preassembled to canopy (D))
F Track Section
2
1
G Track Head 3
Lowes.com
3
HARDWARE CONTENTS (shown to size)
AA BB
x 2
Toggle Bolts
(not shown to size)
x 2
Phillips Screw
CC
x 2
Anchor
DD
x 3
Wire Connector
EE
x 2
Machine Screw
SAFETY INFORMATION
Please read and understand this entire manual before attempting to assemble, operate or install
the product.
WARNING
● All electrical connections must be in accordance with local codes and the National Electrical
Code. If you are unfamiliar with methods of installing electrical wiring, secure the services of
a qualified licensed electrician.
● Save these instructions and refer to them when additions to or changes in the track configuration
are made.
● Do not install this lighting system in a damp or wet location.
● Before energizing, make sure the lighting system is clear of all material which could cause a
direct short and check all electrical connections to make sure they are tight.
● Do not install any part of this system less than 7 feet above the floor.
● LIGHTED LAMP IS HOT! Do not install any lamps closer than 6 in. from any curtain or similar
combustible material.
● Disconnect electrical power before adding to or changing the configuration of the track.
● Do not attempt to energize anything other than lighting track fixtures on the track.
● To reduce the risk of fire and electrical shock, do not attempt to connect power tools, extension
cords, appliances, and the like to the track.
● Do not touch lamp at any time. Turn off power and allow lamps to cool down before replacing.
CAUTION
●To reduce the risk of fire and electric shock, use only with Evolution “HBT” track series.
● This track system is to be supplied by a single branch 120-volt, 60-hertz circuit.
● This track system is not intended for use with a power supply cord or convenience receptacle
adaptor.
● This track system is not intended to be supended by a stem or cable.
IMPORTANT SAFETY INSTRUCTIONS
(not shown to size) (not shown to size)
SAVE THESE INSTRUCTIONS
Lowes.com
● Dimmable to 10% with select dimmers: Lutron SCL-153PR-WH, Lutron MACL-153MR-WH,
Lutron TGCL-153PH-WH, LEVITON IPL06-P-LED/LFC, LEVITON 6674-P-LED/LFC.
4
ASSEMBLY INSTRUCTIONS
1. Remove the canopy screws (E) from the canopy (D)
to expose the mounting plate (B). Loosen the
track mounting screws (A) preassembled to the
mounting plate (B). Note: Do not remove the track
mounting screws (A) completely.
2. Connect the wires (white wires from connector
to the white wires from the supply circuit, black
wires from the connector to the black wires from the
supply circuit, and the green ground wire from the
power supply to the ground wire of the supply circuit)
using the wire connectors (DD). Wrap electircal tape
(not included) around wire connectors (DD) and be
sure they are secure. Push all excess wire and
wire connectors (DD) back into the outlet box
(not included).
Outlet Box
Hardware Used
DD x 3
Wire Connector
PREPARATION
Before beginning assembly of product, make sure all parts are present. Compare parts with
package contents list and hardware contents list. If any part is missing or damaged, do not attempt
to assemble the product.
Estimated Assembly Time: 45 minutes
Lowes.com
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment on
and off, the user isencouraged to try to correct the interference by one or more of the following:
Reorient or relocate the receiving antenna.
Increase the separation between the lighting unit and receiver.
Connect the lighting unit into an outlet on a circuit other than the outlet which the receiver is
connected. Consult the dealer or an experienced radio/TV technician for assistance.
1
2
E
D
B
A
DD
Tools Required for Assembly (not included): Wire stripper, Phillips screwdriver, Electrical tape, Drill,
7/32 in. drill bit, 5/8 in. drill bit, Measuring tape, Ladder and Pencil.
Helpful tools (not included): Gloves
FCC CAUTION
5
3
3. Align holes in the mounting plate (B) with holes in
the outlet box. Secure mounting plate (B) to
outlet box with machine screws (EE).
Hardware Used
Outlet Box
EE B
EE x 2
Machine Screw
Lowes.com
4. If you want to field cut the track section (F), mark the
track section (F) at desired length. Take into consideration
the length of connectors (not included) which may be
required for supplying power or attaching additional track
sections (sold separately). Remove end caps by
loosening end cap screws.
Secure the track section (F) and, with a blunt instrument
(a mallet, for example; not included), tap on the copper
strip on interior buss bars until they are dislodged.
Reattach the end caps with the interior buss bars in place.
From other end, measure track section (F) to desired length
considering end cap will add an 1/8 inch. With a metal
cutting saw, cut the track section (F) at mark.
Make sure the cut is straight with no burrs.
With one end cap in place, pull the copper strips out and cut
3/8 in. off of each strip. Push the copper strips back in and
replace other end cap or make connection to other track
connector (not included).
F
F
F
F
4
3/8 in.
3/8 in.
F
a. For toggle bolt installation, drill a 5/8 in. hole at
each mark on ceiling. Insert toggle bolts (AA)
through the track section (F) and thread 1/2 in.
toggle onto bolts. Place track section (F) against
the ceiling and insert toggle bolts (AA) into holes
until they spring open; tighten bolts.
6. Place the linear track section (F) in the desired location on the mounting plate (B) between the
two track mounting screws (A). Mark the location of the track section (F) on the ceiling with a
pencil (not included) through the mounting holes in the bottom of the track section (F). Attach the
track section (F) to the desired location on the ceiling in one of the following ways:
Hardware Used
x 2
Toggle Bolts
6a
6
b. For anchor installation, drill a 7/32 in. hole at each
mark on the ceiling, and insert anchors (CC) into
the mounting surface. Insert the Phillips screws
(BB) through the track section (F) and tighten to
anchors (CC).
NOTE: Toggle bolts (AA) should be used for standard installation into drywall, drop ceiling or
suspended ceiling applications. Anchors (CC) are used for masonry installations ONLY.
6b
Hardware Used
BB x 2
Phillips Screw
CC x 2
Anchor
F
BB
CC
Lowes.com
5. When shortening track section (F), additional holes may be
required to allow for proper installation. To drill holes in track
section (F), determine where on the length of the track section
the holes will be required (see following note) and mark on the
ceiling side of the track section (F). From this mark, measure
from the side to the middle of the track and drill a 3/16 in. hole.
Remove any burrs.Take care not to damage the buss bars or
copper strips.
Note: A single section of track that is 4 ft. or less in length is to be used with one mounting
opening spaced a maximum of 6 in. from each end of the track section (F). Additional openings
might also be provided. A single section of track that is greaterthan 4 ft. in length is to be used
with a mounting opening spaced a maximum of 12 in. from each end of the track section F), with
additional openings being placed a minimum of every 4 ft. along the length of the track section (B).
5
F
AA
F
AA
7. Tighten the track mounting screws (A) to secure
the track section (F) to the mounting plate (B). 7
B
F
A
8. Twist the power supply (C) into the track
section (F). Secure the canopy (D) to the
mounting plate (B) by tightening the previously
removed canopy screws (E).
Note: When the power supply (C) is twisted
into position on the track section (F), make sure
the two copper tabs on the side of the power supply
(C) align with the two copper strips inside
the track section (F). This is necessary to
maintain polarity.
8
7
9. Identify ground side on the track head (G) connector
and track section (F).
Push the top portion of the track head (G) connector
into the slot of the track section (F). Pull down the
connector’s locking tab. Twist ground side of the
track head (G) connector toward the ground side
the track section (F) until the track head (G)
connector snaps into place.
NOTE: The ground side of the track head (G)
connector is the side with two metal tabs. The
ground side of the track section (F) has an indented
groove on the face and two internal copper strips.
The track head (G) can only be assembled if the
ground sides of the track head (G) connector and
the track section (F) are aligned.
Lowes.com
B
A
F
B
C
F
D
E
GROUND
TAB
GROUND GROOVE
GROUND SIDE OF
CONNECTOR
9
G
F
10. To remove the track head (G) from the track
section (F), first allow the track head (G) to cool
down. Pull down on the track head (G)
connector’s locking tab, and twist until the
track head (G) disengages.
8
WARRANTY
Printed in China
TROUBLESHOOTING
PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION
1. Power is off.
2. Incorrect wiring.
3. Faulty light switch.
4. Connector or track head
may be installed improperly.
1. Make sure power supply
is on.
2. Check wiring connection at
power source and at track
power feed.
3.
Test or replace light switch.
4. Check the connections for
proper installation.
Blown fuse or tripped circuit
breaker when fixture is
turned on.
1. Incorrect wiring. 1. Check wiring connection at
power source and at track
power feed.
CARE AND MAINTENANCE
● Before attempting to clean the fixture, disconnect the power to the fixture by turning the breaker
off or removing the fuse from the fuse box.
● To clean the fixture, use a dry or slightly dampened clean cloth.
● DO NOT use any cleaners with chemicals, solvents, or harsh abrasives as damage to the fixture
may occur.
Lowes.com
Project Source® is a registered trademark of LF, LLC. All rights reserved.
● 23-watt total LED included; do not attempt to replace the LEDs.
Light will not turn on.
10
G
F
ENERGY STAR qualified Solid State product with non replaceable components is warranted for
five (5) years.
This warranty does not cover parts becoming defective due to misuse, accidental damage, improper
handling and/or installation and specifically excludes liability for indirect, incidental or consequential
damages. Product found to be defective may or may not be replaced with same or like-type product,
contingent on the nature of the defect, and/or replacement availability and/or compensated for at a
pro- rated value. This warranty gives you specific rights and you may also have other rights, which
vary from state to state. Proof of purchase is required to exercise the warranty.
9
JOIGNEZ VOTRE REÇU ICI
Numéro de série Date d’achat
Des questions, des problèmes, des pièces manquantes? Avant de retourner l’article au
détaillant, appelez notre service à la clientèle au 1 866 389- 8827, entre 8 h et 18 h (HNE),
du lundi au jeudi, ou entre 8 h et 17 h (HNE) le vendredi.
Lowes.com
10 Lowes.com
CONTENU DE L′EMBALLAGE
PIÈCE DESCRIPTION QUANTITÉ
A Vis de montage du rail (préassemblée à la plaque de montage [B]) 2
B Plaque de montage 1
C Connecteur d’alimentation (préassemblé à la plaque de montage [B]) 1
D Couvercle (préassemblé à la plaque de montage [B]) 1
E Vis de couvercle (préassemblée au couvercle [D])
FRail
2
1
G Projecteur 3
Ce manuel convient aux modèles suivants
1
Table des matières
Langues :
Manuels Projecteur populaires d'autres marques
VIZULO
VIZULO Micro Martin Guide de l'utilisateur
EuroLite
EuroLite LED IP FL-100 SMD Manuel utilisateur
Cooper Wheelock
Cooper Wheelock XB12 Manuel utilisateur
Allen + Roth
Allen + Roth 17624-000 Manuel utilisateur
ADJ
ADJ 4 STAGE PAK Manuel utilisateur
Cooper Lighting
Cooper Lighting EGL91SW233 Manuel utilisateur
