ProHD DT-X93Hx2 Manuel utilisateur
1
Model: DT-X93Hx2
9”x2 FHD Rack Mount LCD Monitor
User Manual
Ver: A
Please read this User Manual
throughout before using.
2
Preface
1. All internal technologies of this product are protected, including device, software and trademark.
Reproduction in whole or in part without written permission is prohibited.
2. All brands and trademarks are protected and other relative trademarks in this user manual are the
property of their respective owners.
3. Due to constant effort of product development, SWIT Electronics reserves the right to make
changes and improvements to the product described in this manual without prior notice.
4. The warranty period of this product is 2 years, and does not cover the following:
(1) Physical damage to the surface of the products, including scratches, cracks or other damage to
the LCD screen or other externally exposed parts;
(2) The LCD dot defects are not over three;
(3) Any damage caused by using third-party power adaptors;
(4) Any damage or breakdown caused by use, maintenance or storage not according to the user
manual.
(5) The product is disassembled by anyone other than an authorized service center.
(6) Any damage or breakdown not caused by the product design, workmanship, or manufacturing
quality, etc.
3
Maintenance
Warning
1. In order to reduce the risk of fire and electrical shock, do not lay this product in rain or damp
places.
2. Please keep away from the strong magnetic field; it may cause the noise of the video and audio
signals.
The power
1. Please use the power adapter provided or recommended by the manufacturer in order to avoid
damage.
2. For a third party power adapter, please make sure the voltage range, supplied power, and
polarity of power lead are fit.
3. Please disconnect the power cable under the following situations:
(A). If you do not operate this monitor for a period of time;
(B). If the power cable or power adaptor is damaged;
(C). If the monitor housing is broken.
The monitor
1. Please don't touch the screen with your fingers, which would probably deface the screen.
2. Please don't press the screen; the LCD is extremely exquisite and flimsy.
3. Please don't lay this product on unstable place.
Cleaning
1. Please clean the screen with dry and downy cloth or special LCD cleanser.
2. Please do not press hard when cleaning the screen.
3. Please do not use water or other chemical cleanser to clean the screen. The chemical may
damage the LCD.
4
Contents
Preface .................................................................................................................................................................. 2
Maintenance ......................................................................................................................................................... 3
Contents ................................................................................................................................................................ 4
Installation Dimension ......................................................................................................................................... 5
Operation Instructions ......................................................................................................................................... 6
·Front Panel .......................................................................................................................................................... 6
·OSD .............................................................................................................................................................. 7
·Back Panel ........................................................................................................................................................... 9
Sub-Menu ............................................................................................................................................................ 11
Specification ........................................................................................................................................................ 17
Trouble-shooting................................................................................................................................................. 18
5
Installation Dimension
The main body (in mm)
6
Operation Instructions
·Front Panel
⑴ Speaker: For SDI/HDMI embedded audio and analog audio monitoring.
(Will not work if headphone socket is plugged in)
⑵ Button
SOURCE: Press “SOURCE” to select SDI1, SDI2, HDMI, and CVBS signal input
F1～F5: User definable function keys. Please see details in “4. Function key” under “Main Menu”.
AUDIOBAR: Press “AUDIOBAR” to turn on or turn off the audio meters display.
DISPLAY: Press “DISPLAY” to turn on or turn off relevant status information.
⑶ Rotary Knob
BRIGHT: 0-100 value adjustment and the default value is 50
CONTRAST: 0-100 value adjustment and the default value is 50
SATURATION: 0-100 value adjustment and the default value is 50
MENU/ENTER: When the menu is inactivated, presses “MENU/ENTE” to turn on the main menu;
Revolve “MENU/ENTER” to adjust settings or parameters, and press to apply;
When the menu is inactivated, revolve “MENU/ENTER” to adjust sound volume.
⑷ POWER: Power on/off
⑸ TALLY Light: Red, Green and Yellow 3-color TALLY indicator
7
·OSD
⑴ Timecode（SDI）
Under SDI input, it can display Timecode. If no Timecode information is detected, it will be
displayed as “TC: UNLOCKED”.
User can set function keys F1～F5 or GPI pins as “Timecode” to turn on or off this function.
⑵ UMD
Set up the UMD under ‘UMD” submenu.
⑶ AFD (SDI)
User can set function keys F1～F5 or GPI pins as “AFD” to turn on or off this function. If no
relevant information is detected, it will be displayed as “AFD: UNLOCKED”.
⑷ Audio
Monitor the audio information. The relevant parameters like position, audio channels and blending,
etc can be changed under “Audio” submenu.
User can set function Keys F1～F5 or GPI pins as “Audio” to turn on or off this function.
8
Introduction of audio and video functions
2-ch embedded audio meters
Under SDI and HDMI input, it displays 2 channels embedded audio meters, and under analog
input, the monitor displays 2 channels analog audio meters. The audio meter is green, and will
turn yellow when audio exceeds -20dB, and turn red when audio exceeds -9dB.
Audio alarm
If the embedded audio value is too low or no audio input, it will display “MUTE” or “UNLOCKED” in
the audio bar.
Timecode (SDI)
Under SDI input, it can display the SMPTE timecode (VITC1, VITC2 or LTC) on the top of the
screen, which is used extensively for synchronization, and for logging and identifying material in
recorded media. If no Timecode information is detected, it will be displayed as “UNLOCKED”.
Internal Color Bar
Under SDI and HDMI input, it has 100% internal color bar which helps to analyze the monitor color
and adjust the display parameter.
User can set function Keys F1～F5 or GPI pins as “color bar” to turn on or off this function.
Peaking focus assist (red/blue switch)
The Peaking focus assist function is to mark the sharpest edges of the image with red or blue
color under SDI and HDMI input, for users to check if the subjects are focused.
User can set function Keys F1～F5 or GPI pins as “Focus Assist” to turn on or off this function.
Zebra stripes
Zebra Stripes are used to check if the image is over exposed or not by showing black and white
lines on the monitor. It is considered over exposed when luminance value exceeds 90%.
User can set function Keys F1～F5 or GPI pins as “Zebra” to turn on or off this function.
Freeze Frame
The freeze frame is to capture and display the current broadcast frame.
User can set function Keys F1～F5 or GPI pins as “Freeze Frame” to turn on or off this function.
R/G/B/Mono
R/G/B/Mono is to display only the blue/red/green primary signal or the luminance signal only so as
to monitor the image noise.
User can set function Keys F1～F5 or GPI pins as “R/G/B/Mono” to turn on or off this function.
False Color
The false color is used to aid in the setting of camera exposure. Under false color mode, there’s a
color chart on the bottom of screen for reference. The color from the dark to the bright will be
displayed as blue, cyan, green, yellow, orange and red in a consecutive way. User can set
function Keys F1～F5 or GPI pins as “False color” to turn on or off this function.
AFD (SDI)
It is the abbreviation of active format description. AFD is to display the SDI embedded AFD
information graphically on the screen.
H/V Delay (SDI)
Under SDI input, H/V Delay can be used to display line/field blanking signal, and to observe the
horizontal and vertical synchronous signal.
UMD
When using external control unit, it can display the video source ID and tally information on the
screen.
Flip and Rotate
The image can be set up/down flip, or left/right mirror display, like:
Normal Left to right Up to down 180° Rotate
9
·Back Panel
⑴ GPI: TSL UMD&GPI control socket
⑵ SDI-LOOP1: SDI loop through output from SDI-IN1 (BNC)
⑶ SDI-LOOP2: SDI loop through output from SDI-IN2 (BNC)
⑷ CVBS-OUT: CVBS through output from CVBS-IN (BNC)
⑸ HDMI Socket
HDMI-IN: HDMI input (HDMI-A)
HDMI-OUT: HDMI loop through output from HDMI-IN (HDMI-A)
⑹ AUDIO IN: 3.5mm analog audio input
⑺ AUDIO OUT: 3.5mm audio output, SDI/HDMI embedded audio and analog audio output
⑻ DC IN: Connect with 4-pin XLR power adapter, support 6.5V-24V voltage input (Pin 1: Negative,
Pin 4: Positive)
⑼ CVBS-IN: CVBS input (BNC)
⑽ SDI-IN2: SDI input (BNC)
⑾ SDI-IN1: SDI input (BNC)
⑿ USB: User firmware upgrade socket
⒀ AC-DC Power Adaptor
10
Main Menu
DT-X93Hx2 has OSD to adjust the parameters and settings, for example: Picture, color temp., function
keys, etc.
1. Press “MENU/ENTER” button, the main menu will pop-up from the left top of the screen. The
selected main menu highlights in yellow.
2. Revolve “MENU/ENTER” to select submenu, the selected submenu highlights in yellow, press
“MENU/ENTER” to apply and enter into the selected submenu’s items.
3. Revolve “MENU/ENTER” to select the item which needed to adjust, press “MENU/ENTER”, the
selected item and its parameters will be highlighted in yellow.
4. Revolve “MENU/ENTER” to change the selected item’s parameter, press “MENU/ENTER” to apply
and save the settings.
5. Revolve “MENU/ENTER” to select “Exit”, press “MENU/ENTER” to quit submenu. Select “Exit &
Status” under the Main Menu and press to quit Main Menu.
Notice:
* The items in gray cannot be set up.
* If there is no operation under the set time, the menu will automatically save settings and quit.
* If the key inhabit function is turned on, except key inhibit function, all other items are in grey. Please
turn off the key inhibit function to adjust the items.
Table des matières
Autres manuels ProHD Moniteur
ProHD
ProHD ProHD DT-X71F Manuel utilisateur
ProHD
ProHD DT-N17H Manuel utilisateur
ProHD
ProHD ProHD DT-X71C Manuel utilisateur
ProHD
ProHD DT-X92F Manuel utilisateur
ProHD
ProHD DT-X51Hx3 Manuel utilisateur
ProHD
ProHD DT-X24H Manuel utilisateur
ProHD
ProHD DT-X92Hx2 Manuel utilisateur
ProHD
ProHD DT-X7HUx2 Manuel utilisateur
ProHD
ProHD ProHD DT-X71FI Manuel utilisateur
ProHD
ProHD DT-X16H Manuel utilisateur
