Progeny Preva Plus Guide de démarrage rapide

Preva Plus Upgrade Instructions

FORM #00-02-0594

ECN: P1713

Rev. C

FORM #00-02-0594

ECN: P1713

REV. C

Purpose

These instructions facilitate the upgrade of a Preva DC Intraoral X-ray (manufactured

after July 1, 2008) to a Preva Plus with integrated Vision DX Sensor.

Items required for this upgrade may include one or more of the following

Part Numbers:

600-401 – Upgrade Kit with #1 Sensor

600-402 – Upgrade Kit with #2 Sensor

600-403 – Upgrade Kit with #1 and #2 Sensor

600-404 – Upgrade Kit without Sensor

Options

600-100, USB Ethernet Extender

30-A2153, USB A/B Switch

Tools Required

Philips Screwdriver, #1

Philips Screwdriver, #2

3mm Hex Wrench

Diagonal Cutter

Procedure

1. Remove the end caps from the tube head end of the articulating arm by pulling

them apart.

Figure 1

2. Locate the cable tie that holds the end of the USB cable to the arm. Refer to

Figure 2.

Figure 2

3. Carefully cut the cable tie with a diagonal cutter. Take extreme care not to cut

the USB cable jacket.

4. Plug the USB cable into J1 of the Sensor Interface PCB, Arm Mount Kit. Refer to

Figure 3.

FORM #00-02-0594

ECN: P1713

REV. C

Figure 3

5. Replace the male end cap with Sensor Interface PCB,Arm Mount Kit. Press it

and the female end cap together over the end of the Articulating Arm.

6. Secure the Sensor Interface PCB, Arm Mount Kit to the Articulating Arm using

the M3 x 16mm socket head cap screw. Use a 3mm hex wrench to tighten.

Refer to Figure 4.

Figure 4

7. Attach the sensor holder to the articulating arm as shown in Figure 5.

FORM #00-02-0594

ECN: P1713

REV. C

Figure 5

8. Plug the sensor connector into the Sensor Interface at the bottom of the Arm

mount. Figure 6.

Figure 6

9. Place the sensor into the sensor holder. Refer to Figure 7.

Figure 7

FORM #00-02-0594

ECN: P1713

REV. C

FORM #00-02-0594

ECN: P1713

REV. C

11. t to the Logic pcb. Use

the two M3x5mm screws provided. Refer to Figure 8.

12. the horizontal arm. If it is secured

13. from the horizontal arm into J1 of the Unpowered USB Hub.

14. e 5m USB cable provided to J2 of the Unpowered USB Hub. Refer to

15. in the control cover using one of the provided access

areas. See fig. 8a.

10. Remove the cover from the Preva Plus Control Unit.

Attach the Unpowered USB Hub to the bracket adjacen

Figure 8

Locate the free end of the USB cable from

with a cable tie, carefully cut the cable tie.

Plug the USB cable

Refer to Figure 8.

Connect th

Figure 8.

Cut and clear a notch

Figure 8a.

16. Dress the 5m USB cable through the notch in the bottom of the Control Unit

cover and replace the cover.

FORM #00-02-0594

ECN: P1713

REV. C

17. Plug the other end of the 5m USB cable into a USB port on the PC that will

control the VisionDX system.

Option

upply to the hub and then connect the PC to the 4-Port USB Hub

using the 1m USB Cable. Plug the free end of the 5m USB Cable into the 4-Port

2. B cables. A USB – ethernet

ada

cable in

b. Attach

pcb. Us

escribed in the above step.

. Plug the USB cable from the horizontal arm into the USB-Ethernet

OPTION 1: USB Powered Hub. It is recommended to use a powered hub at the

computer to prevent overloading and any electrical power issues at the

computer. Plug the 4-Port USB Hub Power Supply into a wall outlet. Connect

the power s

USB Hub.

OPTION 2: USB-Ethernet Extender, part number 600-100. This extender

provides for a longer cable run than permitted by US

pter is used on both the computer end and the sensor end with an ethernet

between that can run up to 25 ft. in length.

a. In the cases where the PC cannot reach the Preva Plus Control Unit wit

the 5m USB cable, a USB-Ethernet Extender may be used.

the USB-Ethernet Extender to the bracket adjacent to the Logic

e the two M3x5mm screws provided. Refer to Figure 9.

Note: If installed remove and replace the Unpowered USB Hub

with the USB-Ethernet Extender as d

cExtender, Device at J1. Refer to Figure 9.

Figure 9

d. Plug the 0.5m USB Cable into a USB port on the PC that will control the

VisionDx system.

FORM #00-02-0594

ECN: P1713

REV. C

. Plug the free end of the 0.5m USB Cable into the USB Ethernet Extender,

g. Dress the CAT-V cable through the notch in the bottom of the Control Unit

re the Preva Plus and VisionDX Integrated System is used in a

pass-though cabinet and a PCs is desired for each room, a Dual-Host Switch

a. ub from the bracket inside the Control Unit.

. Plug the two USB cables for each of the two PCs into J1 and J3 on the

Dual-Host Switch Assembly. Refer to Figure 10.

eHost with Enclosure. Refer to Figure 10.

Figure 10

f. Use the 50 foot CAT-V Cable to link to the USB-Ethernet Extender

Device.

cover and replace the cover.

OPTION 3: Dual-Host Switch, part number 30-08135.

In the case whe

y be used.

Remove the USB H

b. Replace the Control Insert in the Control Unit Cover with the Dual-Host

Switch Assembly.

c. Plug the USB cable from the Preva Plus Horizontal Arm into J2 on the

Dual-Host Switch Assembly.

Figure 11

e. Dress the two USB cables through the notch in the bottom of the Control

Unit cover and replace the cover. Refer to Figure 10.

Figure 12

Plug one USB cable into a USB Port on each of the PCs in use.

FORM #00-02-0594

ECN: P1713

REV. C

Option 4: Mobile Installation

Figure 13.

a. With the operator panel and the cradle removed, route the USB cable and the

control panel computer cable through the hole in the cradle bas as shown in figure

13.

b. Route the control panel computer cable through the cradle and the USB cable in

the slot at the bottom of the cradle as shown in figure 14.

FORM #00-02-0594

ECN: P1713

REV. C

Autres manuels Progeny Équipement médical

Progeny

Progeny Vivid Manuel utilisateur

Manuels Équipement médical populaires d'autres marques

TekTone

TekTone Tek-CARE160 Manuel utilisateur

NeuroMetrix

NeuroMetrix Quell 2.0 Manuel utilisateur

AMT

AMT XLR8 Manuel utilisateur

Medipost-Nutristoma

Medipost-Nutristoma MD300K2 Manuel utilisateur

EDAN

EDAN SONOTRAX Pro Manuel utilisateur

Restorative Therapies

Restorative Therapies RT300 Manuel utilisateur

Gendex

Gendex Expert DC Manuel utilisateur

Dexcowin

Dexcowin ADX4000W Manuel utilisateur

Libelium

Libelium MySignals Manuel utilisateur

Acelity

Acelity V.A.C.ULTA 4 Manuel utilisateur

Caputron

Caputron ActivaDose II tDCS Manuel utilisateur

FujiFilm

FujiFilm Sonart Manuel du propriétaire

Plinth 2000

Plinth 2000 93CDT Manuel utilisateur

GE SENOGRAPHE 800T Manuel utilisateur

GE Definium 5000 Manuel utilisateur

Kanmed

Kanmed GE-1380 Manuel utilisateur

Huntleigh

Huntleigh FD1 Manuel utilisateur

Stryker

Stryker SPR Plus Manuel utilisateur