ProFusion PH-935E Manuel utilisateur

240V/4800W HEAVY DUTY HEATER WITH THERMOSTAT

OWNER’S MANUAL

MODEL: PH-935E

IMPORTANT INSTRUCTIONS

READ & SAVE

WARNING

NOT FOR HOUSEHOLD USE

THIS IS A FLOOR HEATER ONLY

Technical support: 1-866-206-0888

Service email: inf[email protected]

TABLE OF CONTENTS

Important Instructions……………………………………….. 3

Parts of the heater ……………………….………………… 5

Grounding and Operating Instructions…………………… 5

Specifications ………………………………………………. 6

Cleaning and Maintenance………………..………………. 6

Storage……………………………………………………… 6

Troubleshooting……………………………………………. 7

Warranty Information………………………………………. 7

IMPORTANT INSTRUCTIONS

PLEASE READ ALL INSTRUCTIONS BEFORE USING THIS HEATER

NOTE: There may be a trace of smoke or odor when unit is first operated. Do not be

alarmed. This indicates that a drop of oil fell on the heating coil during the manufacturing

process. It will quickly evaporate and should not re-occur.

Make sure that the room in which the appliance is located is well ventilated during this

operation. It is normal for the appliance to emit small cracking sounds when you turn it on

for the first time. Do not be alarmed.

WHEN USING ELECTRICAL APPLIANCES, BASIC PRECAUTIONS SHOULD ALWAYS BE

FOLLOWED TO REDUCE RISK OF FIRE, ELECTRICAL SHOCK AND INJURY TO PERSONS

OR PROPERTY, INCLUDING THE FOLLOWING:

1. Read all instructions before using this heater.

2. This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. Keep

combustible materials, such as furniture, pillows, bedding, papers, clothes and curtains at least

3 ft. (0.9 meters) from the front and top of the heater and keep them away from the sides and

rear. Ensure a minimum clearance of 5.5 inches (14 cm) from both sides and rear of heater to

adjacent walls. Keep the rear grille away from walls or drapes so as not to block the air intake.

3. Extreme caution and reasonable supervision is necessary when any heater is used by or near

children, invalids or pets and whenever the heater is left operating and unattended.

4. Always unplug heater when not in use. To disconnect, grip plug and pull from wall outlet.

Never yank on cord.

5. To disconnect the heater, turn controls to “OFF”, then remove the plug from outlet.

6. Do not operate any heater with a damaged cord or plug or after the heater malfunctions or has

been dropped or damaged in any manner. Return heater to an authorized service facility for

examination, electrical or mechanical adjustment or repair.

7. Do not use outdoors.

8. This heater is not intended for use in bathrooms, laundry areas and similar indoor locations.

Never locate heater where it may fall into a bathtub or other water container.

9. Do not run cord under carpeting. Do not cover cord with throw rugs, runners or the like. Do

not route cord

under furniture or appliances. Arrange cord away from traffic area where it will not be tripped

over. Route the cord so that it will not be walked on, or pinched by furniture.

10.Connect to properly grounded outlets only. Check heater voltage and amperage on the back of

the heater to make sure it agrees with the electric service supplied.

11.Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may

cause an electric shock, fire or damage to the heater.

12. To prevent a possible fire, do not block air intakes or exhaust in any manner. Do not use on

soft surfaces, like a bed, where openings may become blocked.

13.Use this heater only as described in this manual. Any other use not recommended by the

manufacturer may cause fire, electric shock, injury to persons or other damage to property.

14.This heater draws 20 Amps during operation. Be sure to use a dedicated 240VAC, 30A circuit

for the heater.

15.It is normal for the heater’s plug and cord to feel warm to the touch. A plug or cord which

becomes hot to the touch or becomes distorted in shape may be a result of a worn electrical

outlet. Worn outlets or receptacles should be replaced prior to further use of the heater.

Plugging heater into a worn outlet/ receptacle may result in overheating of the power cord or

fire.

16.Ensure the heater is on a stable, secure floor surface to eliminate the potential of tipping it

over.

17.Be sure that the plug is fully inserted into appropriate receptacle. Please remember that

receptacles also deteriorate due to aging and continuous use: check periodically for signs of

overheating or deformations evidenced by the plug. Should this occur, do not use the

receptacle if deteriorated. CALL your electrician.

18.Check that neither the appliance nor the power cable has been damaged in any way during

transportation.

19.Make sure that no pieces of polystyrene or other packaging material have been left between

one element of the appliance and another. It may be necessary to pass over the appliance with

a vacuum cleaner.

20.When switching on the appliance for the first time, you may notice a slight odor which is normal

with new electrical appliances. Allow odor to dissipate by running appliance at full power for

about ten minutes. Make sure that the room in which the appliance is located is well ventilated

during this operation. This heater draws 20 Amps during operation. To prevent overloading a

circuit, do not plug the heater into a circuit that already has other appliances working.

21.Do not run in locations when the heater will be left unattended for long periods of time. (For

example - in an unoccupied summer cottage).

22.Do not use attachments or filters. They are not recommended.

23. Always plug heater directly into a wall outlet/receptacle. Never use with an extension cord or

relocatable power tap (outlet/power strip). A heater has hot and arcing or sparking parts

inside. Do not use it in areas where gasoline, paint or flammable liquids are used or stored.

SAVE THESE INSTRUCTIONS

PET OWNERS WARNING:

The health of some small pets including birds are extremely sensitive to the fumes produced

during the first-time use of many appliances. These fumes are not harmful to humans but we

recommended that you do not use your heater around birds and small pets during its initial use

until the manufacturing corrosion coatings burn off.

WARNING –RISK OF FIRE, DO NOT USE AS A

RESIDENTIAL OR HOUSEHOLD HEATER

CAUTION: This appliance is not intended for use by persons (including children)

with reduced physical, sensory or mental capabilities, or lack of experience and

knowledge, unless they have been given supervision or instruction concerning use

of the appliance by a person responsible for their safety.

1. Carry handle

2. Housing

3. Safety grille

4. Heating element

5. Thermostat control

6. Plug (NEMA #6-30P)

!! IMPORTANT

THIS HEATER IS FOR USE ON THE FLOOR ONLY.

Prior to operating the heater, ensure the electrical receptacle is of the configuration and

capacity appropriate for the heater. See receptacle configuration in OPERATING

INSTRUCTIONS. This heater is for use on 240 volts. The cord has a plug as shown in #6. No

adapter is available for this blade configuration, and none should be used. The type of

receptacle is a 240 volt grounding receptacle (NEMA 6-30R). When properly installed, it

provides a ground connection through the cord to the heater to protect the operator from

electric shock.

Receptacle: NEMA #6-30R 250V 30 Amps Plug: NEMA #6-30P 250V 30 Amps

PARTS OF THE HEATER

GROUNDING AND OPERATING INSTRUCTIONS

YOUR HEATER IS EQUIPPED WITH A THERMOSTAT:

1. Turn the unit on by turning the thermostat dial away from the OFF position.

2. For faster heat up or to increase the heat output, turn the Thermostat Control knob all the way

to the right [MAX]. The thermostat function controls the temperature output. To decrease the

heat output, turn the knob counter clockwise.

3. Once the room reaches the desired temperature, slowly turn the Thermostat Control knob

counter clockwise until you hear a “click”. This sets the heater to cycle ON/OFF to maintain the

desired heating temperature for energy efficiency.

4. To completely shut unit OFF, turn the thermostat dial to the OFF position and unplug the

heater.

Model Number

PH-935E

Power Supply

240 volts AC, 60Hz

Power Consumption

4800W

Before any cleaning, make sure that:

1. The heater is turned OFF.

2. Disconnect power supply at source by removing plug from power outlet.

3. Your heater is now ready for cleaning.

Regular Cleaning:

1. Do not use cleaning liquid or other chemicals to spray on the unit.

2. Interior dust can often be removed by using a vacuum cleaner with a crevice tool attachment.

3. To clean enclosure, use a clean, soft and lightly damp cloth to gently wipe off the dirt from the

surface of the unit. Be sure not to wet the heating element and the switches. Allow the unit to

dry completely before using it.

CAUTION: DO NOT ALLOW WATER TO RUN INTO THE INTERIOR OF THE HEATER AS

THIS COULD CREATE A FIRE OR ELECTRIC SHOCK HAZARD, DAMAGING THE UNIT.

1. Perform the cleaning procedures described in “Cleaning/Maintenance”.

2. Wipe all parts to dry.

3. Pack the heater in a plastic bag and store it in a cool, dry place.

CLEANING AND MAINTENANCE

STORAGE

SPECIFICATIONS

If your heater fails to operate, please follow these procedures before contacting customer

services:

Problem

Probable Cause

Solution

Unit is not

heating.

Overheat protection has

temporarily deactivated the

heater.

Turn the heater OFF; unplug it and

ALLOW IT TO COOL. Inspect and

remove any objects on or adjacent to

the heater. Wait 30 minutes before

plugging unit back in.

Room temperature has been

warmed up to thermostat setting.

To increase the room temperature,

adjust thermostat control knob to a

higher setting by turning clockwise.

Heater is not plugged into a 240V

grounded outlet/receptacle.

Ensure unit is in OFF position. Plug in

unit and attempt to turn on again.

Breaker/Fuse has been tripped.

▪Check your electrical box to confirm

the breaker has not been blown.

This may occur if the receptacle is

shared between other high

consumption appliances.

▪Ensure unit is in the OFF position.

Plug in unit and attempt to turn on

again.

The heater is

creating a

burning smell.

A drop of oil fell on the heating

coil during the manufacturing

process. It will quickly evaporate

and should not occur again.

Ensure room in which heater is situated

is well ventilated.

Check & ensure there are no

combustible materials within 0.9

meters (3 feet) surrounding the

heater.

Remove any combustible items from the

heater.

Ensure a minimum clearance of

5.5 inches (14 cm) from both

sides and rear of heater to

adjacent walls.

Reposition the heater so there is

enough space around the heater to the

adjacent walls.

PLEASE DO NOT ATTEMPT TO OPEN OR REPAIR THE HEATER YOURSELF. DOING SO

COULD CAUSE DAMAGE OR PERSONAL INJURY.

This product carries a one (1) year warranty against defects in workmanship and materials.

Profusion Heat agrees to replace a defective product, within the stated warranty period, when

returned to the place of purchase with proof of purchase. This product is not guaranteed against

wear or breakage due to misuse and/or abuse.

TROUBLESHOOTING

WARRANTY INFORMATION

Table des matières

Autres manuels ProFusion Chauffage

ProFusion

ProFusion SHAG-L02F Manuel utilisateur

ProFusion

ProFusion PH-960 Manuel utilisateur

ProFusion

ProFusion PH-9100WS Manuel utilisateur

ProFusion

ProFusion DQ1016A Manuel utilisateur

ProFusion

ProFusion PS-10241 Manuel utilisateur

ProFusion

ProFusion QH-1 Manuel du propriétaire

ProFusion

ProFusion PH-960N Manuel utilisateur

ProFusion

ProFusion FH128B Manuel utilisateur

ProFusion

ProFusion EH-4604 Manuel utilisateur

ProFusion

ProFusion HA11-20M Manuel utilisateur

ProFusion

ProFusion GD9315BC1-N Manuel utilisateur

ProFusion

ProFusion NDB-1Y Manuel utilisateur

ProFusion

ProFusion HFU15-E Manuel utilisateur

ProFusion

ProFusion H-5511 Manuel utilisateur

ProFusion

ProFusion HA22-48M Manuel utilisateur

ProFusion

ProFusion PH-931 Manuel utilisateur

ProFusion

ProFusion PH-960XNR Manuel utilisateur

ProFusion

ProFusion HA24-50E Manuel utilisateur

ProFusion

ProFusion HA24-50MB Manuel utilisateur

ProFusion

ProFusion PH-9100WRN Manuel utilisateur

ProFusion

ProFusion GD8110BP-M Manuel utilisateur

ProFusion

ProFusion Salamander PS-10241P Manuel utilisateur

ProFusion

ProFusion H-4439 Manuel utilisateur

ProFusion

ProFusion WH-50B Manuel utilisateur

Manuels Chauffage populaires d'autres marques

oventrop

oventrop Regucor Series Manuel utilisateur

Blaze King

Blaze King CLARITY CL2118.IPI.1 Manuel utilisateur

ELMEKO

ELMEKO ML 150 Manuel utilisateur

BN Thermic

BN Thermic 830T Manuel utilisateur

KING

KING K Series Mode d’emploi

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Guide de démarrage rapide

Well Straler

Well Straler RC-16B Manuel utilisateur

EUROM

EUROM 333299 Manuel utilisateur

Heylo

Heylo K 170 Manuel utilisateur

Eterna

Eterna TR70W Manuel utilisateur

Clarke

Clarke GRH15 Mode d’emploi

IRSAP

IRSAP The Radiator Company Ovali Manuel utilisateur

Empire Heating Systems

Empire Heating Systems WCC65 Manuel utilisateur

Wetekom

Wetekom 92 86 43 Manuel utilisateur

Desa

Desa SPC170-F Manuel utilisateur

Watlow

Watlow Watrod Electric Tubular Heaters Manuel utilisateur

Haverland

Haverland ECO-DRY GPS Series Manuel de la liste des pièces

Stelpro

Stelpro ASILVC2060 Series Manuel utilisateur