ProFire PF2200-SB Manuel utilisateur

PF2200-SB

USER GUIDE

TABLE OF CONTENTS 
OVERVIEW....................................................................................................................................................... 3 
STATUS LED ................................................................................................................................................................ 3 
STARTING/STOPPING ................................................................................................................................................. 4 
NAVIGATION............................................................................................................................................................... 4 
MENU MAP................................................................................................................................................................. 5 
STATUS SCREEN.......................................................................................................................................................... 6 
OPERATIONAL STATES......................................................................................................................................7 
POWER ON STATE....................................................................................................................................................... 7 
LOCKOUT STATE ......................................................................................................................................................... 7 
ALARM STATE ............................................................................................................................................................. 8 
READY STATE .............................................................................................................................................................. 8 
WAITING STATE.......................................................................................................................................................... 9 
IGNITION STATE........................................................................................................................................................ 10 
PILOT STATE.............................................................................................................................................................. 11 
MAIN LIGHT-OFF STATE............................................................................................................................................ 11 
PROCESS CONTROL STATE........................................................................................................................................ 12 
SETTINGS....................................................................................................................................................... 13 
TEMPERATURE INPUTS............................................................................................................................................. 13 
FLAME DETECTION I/O (ION +/-) .............................................................................................................................. 14 
EMERGENCY SHUTDOWN INPUT ............................................................................................................................. 15 
LEVEL/FLOW INPUT.................................................................................................................................................. 15 
PRESSURE INPUT ...................................................................................................................................................... 15 
AUXILIARY INPUTS.................................................................................................................................................... 15 
SYSTEM SCREEN............................................................................................................................................. 16 
EVENT LOG SCREEN .................................................................................................................................................. 16 
DATA LOGGING SCREEN ........................................................................................................................................... 16 
SYSTEM DIAGNOSTICS SCREEN ................................................................................................................................ 17 
FLAME DIAGNOSTICS SCREEN .................................................................................................................................. 18 
STATUS PRIORITY SCREEN ........................................................................................................................................ 18 
ABOUT SCREEN......................................................................................................................................................... 18 
RESET/BACKUP/RESTORE SETTINGS ........................................................................................................................ 19 
CERTIFICATIONS............................................................................................................................................. 19 
TROUBLESHOOTING....................................................................................................................................... 19 
 

OVERVIEW

This User Guide is intended to help the Operator use the PF2200-SB Burner

Management System.

The keypad located on the front of the unit is the primary method for the

operator to interface with the PF2200 system. It allows for screen

navigation, starting and stopping the burner, as well as allowing

commissioning and adjusting the PF2200 system.

STATUS LED

The Status LED indicator on the front of the PF2200 shows the status of the appliance. The chart below

shows the different states indicated by Status LED.

Below is a description of the different alerts found on the PF2200-SB.

•Alarms - A persistent abnormal condition in either the equipment, or the process.

•Waits - An event causing the BMS to de-energize all safety outputs. when the event clears, the

system is free to recycle.

•Warnings - An event that indicates a possible issue that may arise, but allows the system to

continue running.

•Main Permissive - an event that causes the BMS to de-energize the main solenoid outputs (SSV),

or an Alarm event shuts the system down.

For more information on the PF2200 systems states, see the "OPERATIONAL STATES" on page 10 section

below.

STARTING/STOPPING

Starting, and stopping the burner can be done by selecting the Start or Stop button on

the PF2200.

When starting the system, press the Start button. The system prompts for an

acknowledgment of this action. Press the OK or Start button again to continue with the

safe start-up of the burner. When shutting down the burner, press the Stop button. The

system prompts the user to confirm the shutdown, press OK or the Stop button again.

When the shutdown process is complete, the system will prompt for an acknowledgment that the

shutdown is complete. Press OK to acknowledge the shutdown.

Starting and stopping the burner can also be done with the optional manual

Start/Stop switch. There are three functional positions as shown. When in the stop

position, all safety outputs are de-energized. Toggling from the Run position to the

Ignite position for more than 2 seconds initiates the ignition sequence. Toggling

the switch from the Stop position to the Run and back to the Stop position can

clear a lockout state.

The optional Manual Switch part number PFA-004260 mentioned above can be ordered by contacting

Profire Energy.

Note: Holding the switch in the Ignite position for more than 4.5 seconds results in a system shutdown on

an External Stuck Switch event.

NAVIGATION

See the PF2200-SB Installation Manual for more information on the commissioning of the PF2200-SB.

MENU MAP

Note: The above diagram shows the menu map of the PF2200 in User Mode. This mode has a limited

menu item and options capability.

STATUS SCREEN

•The Status screen can show different

layouts based on a set of priorities that can

be customized in the System screen under

the Status Priority menu item.

•To switch through the different status

screen layouts, use the Plus and Minus

keys while in operation.

•The information displayed in the status screen is dependent on the activation of the various

settings. To change the Priority of what is shown, use the Carousel key to navigate to the System

screen. Use the Arrow keys to highlight Status Priority and press OK. You will then be presented

with a list of all active settings that can be shown in prominence on the status screen. Using the

Arrow keys and the Plus or Minus keys you can change what Status Elements have the higher

priority.

OPERATIONAL STATES

This section describes the different states of the PF2200-SB and outlines the behavior of the system in

each state.

POWER ON STATE

Power On is the default state of the system when power is applied.

If a previous lockout condition is present, the system transitions into the lockout state.

If the system previously shuts down due to a power loss, and the Low Voltage Re-start setting is enabled,

the system purges, and then proceeds to automatically restart the system.

If there are no lockouts, and the system is not automatically re-starting, then the system transitions into

the Ready state.

In this system state, the status of each powered output is as follows:

Powered Output

Status

Pilot 1 / 2

De-energized

Coil 1 / 2

De-energized

SSV

De-energized

HFV

De-energized

LOCKOUT STATE

will stay in the Lockout state until the Lockout is acknowledged by the user.

There are four ways to acknowledge a lockout:

•User Interface: Using the keypad to acknowledge the lockout state.

•Toggling of the Start input: From energized to de-energized.

•Toggling of the Start/Stop Switch: Turning the Optional Manual switch to the Stop position, then

back to the Run position.

•Modbus Interface: Writing the Acknowledge command to clear the shutdown code modbus

In the Lockout state, the status of each powered outputs is as follows:

Powered Output

Status

Pilot 1 / 2

De-energized

Coil 1 / 2

De-energized

SSV

De-energized

HFV

De-energized

For more information on Modbus Register commands, refer to Modbus Registers.

ALARM STATE

indicative of a static problem (e.g., - transmitter not connected, system voltage too low, etc.). The system

can only exit this state when all alarms have cleared.

Once all Alarms are cleared, the system will transition to the Ready state.

In the Alarm state, the status of each powered output is as follows:

Powered Output

Status

Pilot 1 / 2

De-energized

Coil 1 / 2

De-energized

SSV

De-energized

HFV

De-energized

READY STATE

Ready is the system state where the system is idle, and no alarms are present. If there are any alarms

present while in this state, the system moves to the Alarm state. In the Ready state, the system may

proceed to start by one of the following methods:

•Pressing the Start button on the Keypad.

•When the remote start setting is enabled, toggling of the Start input from Open to Closed.

•Holding the Start/Stop switch in the ignite position for greater than 2 seconds.

•Modbus interface starts by writing a start command to the start stop register modbus register.

In this system state, the status of each powered output is as follows:

Powered Output

Status

Pilot 1

De-energized during Pre-Ignition

Pilot 2

De-energized if disabled

Same as Pilot 1 if enabled

Coil 1

De-energized during startup delay

Coil 2

De-energized if disabled

Same as Coil 1 if enabled

SSV

De-energized

HFV

De-energized

For more information on Modbus Register commands, refer to Modbus Registers.

WAITING STATE

Waiting is considered a “running” state of the system, with all powered outputs de-energized. The system

holds this state until all wait conditions have been cleared. Once all waits have been cleared the system

automatically begins the start-up sequence.

Note: purging after a flame loss is considered a wait.

Powered Output

Status

Pilot 1

De-energized during Pre-Ignition

Pilot 2

De-energized if disabled

Same as Coil 1 if enabled

Coil 1

De-energized during startup delay

Coil 2

De-energized if disabled

Same as Coil 1 if enabled

SSV

De-energized

HFV

De-energized

IGNITION STATE

Ignition is the state where a pilot flame is established, and the system achieves this by energizing the coil

and pilot outputs while monitoring flame presence on the ionization inputs.

If a flame is not detected within the pilot-flame establishing period of 4 seconds, the system purges and

restarts the ignition sequence. If the system fails to establish flame 3 consecutive times, the system

proceeds to a lockout state.

If the flame is detected within the Pilot-Flame Establishing period, the system holds the pilot flame for the

user configurable pilot start up delay time to help warm up the appliance, and establish a draft. once the

pilot start up delay time has elapsed, the system transitions to the Pilot State.

Actuating and monitoring of Pilot 2 can be enabled or disabled via the user interface and should only be

enabled if multiple pilots are in use.

If Pilot 2 is enabled, the system requires both flames to be satisfied within the Pilot-Flame Establishing

Period in order to proceed.

If Pilot 2 is disabled, the system only requires Pilot 1 flame to be satisfied within the Pilot-Flame

Establishing Period in order to proceed.

Any Alarms or Waits that occur during this state will cause the system to transition to a Lockout state, or a

Waiting state respectively.

In this system state, the status of each powered outputs is as follows:

Powered Output

Status

Pilot 1

Energized *

Pilot 2

De-energized if disabled

Same as Pilot 1 if enabled

Coil 1

Energized during Ignition

De-energized during startup delay

Coil 2

De-energized if disabled

Same as Coil 1 if enabled

SSV

De-energized

HFV

De-energized

*: The Pilot Outputs are energized 500ms after the Coil Outputs.

Autres manuels pour PF2200-SB

Table des matières

Autres manuels ProFire Contrôleurs

ProFire

ProFire PF2200-SB Manuel utilisateur

ProFire

ProFire PF3100 Series Manuel d'instructions

ProFire

ProFire PF2200-SB Manuel utilisateur

ProFire

ProFire PF2100 Manuel utilisateur

ProFire

ProFire PF3101-00 Manuel utilisateur

ProFire

ProFire PF3100 Series Manuel d'instructions

Manuels Contrôleurs populaires d'autres marques

Digiplex

Digiplex DGP-848 Mode d'emploi

YASKAWA

YASKAWA SGM series Manuel utilisateur

Sinope

Sinope Calypso RM3500ZB Manuel utilisateur

Isimet

Isimet DLA Series Style 2 Manuel d'installation

LSIS

LSIS sv-ip5a Manuel utilisateur

Rockwell Automation

Rockwell Automation 1769-L31 Manuel utilisateur

Airflow

Airflow Uno hab Manuel utilisateur

ABB

ABB ACS580-01 drives Manuel utilisateur

Panasonic

Panasonic GM1 Series Manuel utilisateur

Emerson

Emerson SW93 Manuel utilisateur

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuel utilisateur

Panasonic

Panasonic FP? Positioning Unit RTEX Manuel utilisateur

Samson

Samson Type 5824 Manuel de service

Alpha IP

Alpha IP MIOB 21001 Manuel utilisateur

Siemens

Siemens OpenAir GMA 1 Series Manuel utilisateur

Surecom

Surecom SR-629 Manuel utilisateur

Fishman

Fishman TriplePlay Manuel utilisateur

Regulus

Regulus SRS1 T Manuel utilisateur