Produal HLS 44-SER Manuel utilisateur



USER GUIDE

HLS 44-SER

V1.1.0 (22.04.2014)

1 (6)

Produal Oy Keltakalliontie 18, 48770 Kotka FINLAND Tel: +358 10 219 9100 / Fax: +358 5 230 9210 [email protected]i www.produal.com

Information is subject to change without prior notice.

Commissioning tool HLS 44-SER

HLS 44-SER is a tool for commissioning HLS 44 and HLS 44-V controllers. By using this tool the commissioning is fast and you may rely on

that the settings are as planned.

It is useful to plan and program the settings to the tool with care in advance. After that, you can load the settings to the controllers in office or

on the installation site during commissioning.

This user guide is for the commissioning tool software version 1.1.0 or newer. The tool software version shows on the tool display when the

power is switched on.

PROFILES

HLS 44-SER commissioning tool contains fixed factory settings (PRSET 1) for HLS 44 and HLS 44-V, memory slots for 5 user defined

solutions (SET 1...5) and 4 pre-programmed application profiles (SET 6...9). All parameters of SET 1...9 can be changed for a best possible

room control solution. For more information see the instructions of HLS44 and HLS 44-V.

Pre-programmed applications (SET 6…9) are the following:

SET 6 Heating by radiator and cooling by beam

SET 7 Heating and cooling by a fan coil unit

SET 8 Heating by radiator and cooling by VAV and beam (VAV control based on CO2concentration)

SET 9 Heating by radiator and cooling by beam (dampers and lights ON/OFF by PIR detection; HLS 44-V)

GETTING STARTED

1. Remove the controller cover.

2. Connect the commissioning tool cable to the controller programming terminal.

A. Commissioning tool cable

NOTE: Connecting the tool to the programming terminal will disconnect the controller from the Modbus communication.

3. Connect the supply voltage either to the commissioning tool or the controller.

IMPORTANT: Do not connect the supply voltage to both devices.

4. Check that the software version numbers are compatible.

The software versions are shown on the displays when you switch on the power. See the compatible software versions from the

following table.

HLS 44-SER

software version Compatible HLS 44 and

HLS 44-V software versions

1.0.0 1.0.0 -> 1.0.2

1.1.0 1.1.0 -> 1.1.2

1.1.3 1.1.3

1.1.4 1.1.4 -> 1.1.7

1.1.8 1.1.4 -> 1.1.9



USER GUIDE

HLS 44-SER

2 (6)

Produal Oy Keltakalliontie 18, 48770 Kotka FINLAND Tel: +358 10 219 9100 / Fax: +358 5 230 9210 [email protected]i www.produal.com

Information is subject to change without prior notice.

LOADING PARAMETERS TO THE CONTROLLER

1. Press the and buttons to select the profile (SET 1…9 or PRSET 1) which you want to load to the controller.

2. Press the button to enter the Modbus address setting view.

3. Press the and buttons to select the Modbus address for the controller.

The Modbus address number steps automatically forward number by number, when multiple controllers are programmed.

4. Press the button to load the parameters to the controller.

SETTING THE PARAMETERS IN THE COMMISSIONING TOOL

1. Press the and buttons to select the profile (SET 1…9) in which you want to store the parameters.

NOTE: The selected profile will be overwritten with the new parameters. You cannot recover the overwritten profiles.

2. Press the button.

3. Make the wanted adjustments in the menu.

See the detailed parameter setting instructions from the HLS 44 or HLS 44-V user guide.

4. Load the parameters to the controller.

LOADING PARAMETERS FROM THE CONTROLLER TO THE COMMISSIONING TOOL

1. Press the and buttons to select the profile (SET 1…9) in which you want to load the parameters.

NOTE: The selected profile will be overwritten with the new parameters. You cannot recover the overwritten profiles.

2. Press the button until you reach the parameter loading menu.

…

3. Press the button.

Verification message appears on the display.

4. Press button to change the verification message to “Yes” status.

5. Press the button to load the parameters from the controller to the commissioning tool memory.

ID=

SET

----

COMM

SET

Yes

Sure?

----

LOAD



USER GUIDE

HLS 44-SER

3 (6)

Produal Oy Keltakalliontie 18, 48770 Kotka FINLAND Tel: +358 10 219 9100 / Fax: +358 5 230 9210 [email protected]i www.produal.com

Information is subject to change without prior notice.

MODBUS REGISTERS OF THE SET 6…9 PROFILES

SET 6: Heating with radiator and cooling with beam

COILS

1 Cooling PWM overdrive enable (A1) Off=0, On=1 Off - On 0 No modbus overdrives

2 Cooling 0-10V overdrive enable (Y3) Off=0, On=1 Off - On 0 No modbus overdrives

3 Heating PWM overdrive enable (A2) Off=0, On=1 Off - On 0 No modbus overdrives

4 Heating 0-10V overdrive enable (Y4) Off=0, On=1 Off - On 0 No modbus overdrives

5 VAV overdrive enable (Y1) Off=0, On=1 Off - On 0 No modbus overdrives

6 FAN overdrive enable (Y2) Off=0, On=1 Off - On 0 No modbus overdrives

7 On/Off damper overdrive enable (B1) Off=0, On=1 Off - On 0 No modbus overdrives

8 Light control overdrive enable (B2) Off=0, On=1 Off - On 0 No modbus overdrives

9 Overdrive On/off damper by modbus (B1) Off=0, On=1 Off - On 0 No modbus overdrives

10 Overdrive Light control by modbus (B2) Off=0, On=1 Off - On 0 No modbus overdrives

11 SERVICE ALARM RESET Off=0, On=1 Off - On 0

12 Cooling disabled Off=0, On=1 Off - On 0 Cooling working

13 Heating disabled Off=0, On=1 Off - On 0 Heating working

14 NIGHT MODE Off=0, On=1 Off - On 0 The device is allways in day mode

15 Cooling output mode (DIR/REV) Off=0, On=1 Off - On 0 Direct output mode

16 Heating output mode (DIR/REV) Off=0, On=1 Off - On 0 Direct output mode

17 Cooling stages (1st/2st) Off=0, On=1 Off - On 0 1 stage cooling, chilled beam

18 Sequence of cooling stages (A-st/V-st) Off=0, On=1 Off - On 0 No affect on this process

19 Fan ramp with motor ramp Off=0, On=1 Off - On 1 No affect on this process

20 Night operation mode (DZ/FG) Off=0, On=1 Off - On 0 No affect, if the device is allways in day mode, see Coil 14

21 Night to day setpoint transition Off=0, On=1 Off - On 0 No affect, if the device is allways in day mode, see Coil 14

22 Jam function Off=0, On=1 Off - On 0 the jum fuction is not activated

23 Fan type (3coil/CE) Off=0, On=1 Off - On 0 No affect on this process

24 Fan speed 3 disabled Off=0, On=1 Off - On 0 No affect on this process

25 Fan night to day transition Off=0, On=1 Off - On 0 No affect, if the device is allways in day mode, see Coil 14

26 VAV for heating Off=0, On=1 Off - On 0 No affect on this process, the VAV function is not used

27 Display TE/SP Off=0, On=1 Off - On 0 The display shows the room temperature (not the setpoint)

28 DI2 operation direction Off=0, On=1 Off - On 0 DI2 is not used. No affect on this process

29 Cooling on/off thermostat (off = P/PI) Off=0, On=1 Off - On 0 P/PI mode for cooling

30 Heating on/off thermostat (off = P/PI) Off=0, On=1 Off - On 0 P/PI mode for heating

31 Y1 for cooling (off = VAV) Off=0, On=1 Off - On 0 Y1 is not connected ... No influence

32 Y2 for heating (off = FAN) Off=0, On=1 Off - On 0 Y1 is not connected ... No influence

HOLDING REGISTERS

40001FAN Speed by Modbus 0 … 4 0 - 1 - 2 - 3 - 4 0 No affect on this process

40002Setpoint by Modbus 80 … 500 8,0 … 50,0 °C 210 Temperature setpoint from modbus 21°C

40003Overdrive Cooling PWM by modbus (A1) 0 … 1000 0,00 … 100,0% 0 No modbus overdrives chosen... The value has no affect (see coils 1 ... 10)

40004Overdrive Cooling 0...10V by modbus (Y3) 0…1000 0 …10.00 V 0 No modbus overdrives chosen... The value has no affect (see coils 1 ... 10)

40005Overdrive Heating PWM by modbus (A2) 0 … 1000 0,00 … 100,0% 0 No modbus overdrives chosen... The value has no affect (see coils 1 ... 10)

40006Overdrive Heating 0...10V by modbus (Y4) 0…1000 0 …10.00 V 0 No modbus overdrives chosen... The value has no affect (see coils 1 ... 10)

40007Overdrive VAV by modbus (Y1) 0…1000 0 …10.00 V 0 No modbus overdrives chosen... The value has no affect (see coils 1 ... 10)

40008Overdrive FAN by modbus (Y2) 0…1000 0 …10.00 V 0 No modbus overdrives chosen... The value has no affect (see coils 1 ... 10)

40009DI2 Not used, ext T, door/window, condensation 0 … 3 0 … 3 0 DI2 is not used in this process

40010 Temperature sensor adjustment -30 … 30 -3,0 … 3,0 °C 0 Internal sensor has its factory calibration

40011 Center of user setpoint 180 … 260 18,0 … 26,0 °C 210 Center of the user setpoint 21°C

40012 User setpoint limits 0 … 160 0,0 … 16,0 °C 30 End user can change the setpoint +/- 3 °C from the point above

40013 Control mode 0 … 1 P/PI 1 Control mode PI

40014 Dead zone 0 … 30 0,0 … 3,0 °C 2 Dead zone 2,0 °C

40015 Setpoint relation to Dz 0 … 100 0 … 100% 50 Setpoint is in the center of the dead zone

40016 Proportional band 10 … 320 1,0 … 32,0 °C 20 Proportional band 2,0 °C

40017 Integral time 50 … 5000 50 … 5000s 300 Ti = 300 seconds

40018 Fresh air control: 0:CO2 (T), 1:PIR (T), 2: CO2, 3:PIR 0 … 3 0 … 3 0 No influence because VAV is not used in this process

40019 Dead zone night mode 0 … 100 0,0 … 10,0 °C 60 No affect, if the device is allways in day mode, see Coil 14

40020 FG Thermostat setpoint 80 … 500 8,0 … 50,0 °C 170 No affect, if the device is allways in day mode, see Coil 14 and Coil 20

40021 DI1 mode selection: 0= not used, 1= day night by ext

contact 0 … 1 0 … 1 0 DI1 is not used to controll day/night mode

40022 DI1 operation Direction 0 … 1 0 … 1 0 DI1 not used ... No influence

40023 DI1 delay passive to active 0 … 60 0 … 60min 0 DI1 not used ... No influence

40024 DI1 delay active to passive 0 … 60 0 … 60min 5 DI1 not used ... No influence

40025 “man in house”-button, day extension period 1 … 480 1 … 480min 120 No affect, if the device is allways in day mode, see Coil 14

40026 DI1 boost level 0 … 1000 0,0 … 100,0% 0 DI1 not used ... No influence

40027 U1 mode: not used, CO2, T setpoint, T meas 0 … 3 0 … 3 0 U1 not connected

40028 Minimum of cooling actuator 0 … 500 0,0 … 50,0 % 0 Full operation range from 0%

40029 Maximum of cooling actuator 500 … 1000 50,0 … 100,0 % 1000 Full operation range to 100%

40030 Minimum of heating actuator 0 … 500 0,0 … 50,0 % 0 Full operation range from 0%

40031 Maximum of heating actuator 500 … 1000 50,0 … 100,0 % 1000 Full operation range to 100%

40032 Minimum of FAN output 0 … 500 0,0 … 50,0 % 0 Full operation range from 0%

40033 Maximum of FAN output 500 … 1000 50,0 … 100,0 % 1000 Full operation range to 100%

40034 Minimum of VAV output 0 … 500 0,0 … 50,0 % 0 Full operation range from 0%

40035 Maximum of VAV output 500 … 1000 50,0 … 100,0 % 1000 Full operation range to 100%

40036 Output scale FAN output Hi 0 … 1000 0,00 … 100,0% 1000 The process has not FAN... No influence

40037 Output scale FAN output Low 0 … 1000 0,00 … 100,0% 0 The process has not FAN... No influence

40038 Fan Control 0 … 3 0 … 3 0 The process has not FAN... No influence

40039 Low limit SP for the CO2 control 400 … 1000 400 … 1000ppm 700 The process have not CO2 control ... No influence

40040 High limit SP for the CO2 control 500 … 2000 500 … 2000ppm 1250 The process have not CO2 control ... No influence



USER GUIDE

HLS 44-SER

4 (6)

Produal Oy Keltakalliontie 18, 48770 Kotka FINLAND Tel: +358 10 219 9100 / Fax: +358 5 230 9210 [email protected]i www.produal.com

Information is subject to change without prior notice.

SET 7: Heating and cooling with fan coil unit