prodelin 1134 Manuel utilisateur
4096-393
August 21, 1997
Revision D
ASSEMBLY MANUAL
1.2M Ku-BAND Rx/Tx
SERIES 1134
ANTENNA SYSTEM
PRODELIN CORPORATION
1.2M Ku-BAND Rx/Tx
SERIES 1134 ANTENNA SYSTEM
D Revised per ECN2246 082197 PGW
C Updated 3/18/97 PGW
B Revised for back structure modification 9/16/96 PGW
ARevise pgs. 5,7,8; Step 6, pg. 13. Figure 1 and 3 for
clarity. 5/1/96 R Frye
- ORIGINAL RELEASE 01/10/95 R Frye
REV. DESCRIPTION DATE APPROVED
4096-393
PRODELIN CORPORATION 1.2M Ku-BAND Rx/Tx SERIES 1134
2
4096-393
PRODELIN CORPORATION 1.2M Ku-BAND Rx/Tx SERIES 1134
3
TABLE OF CONTENTS
SECTION TITLE
I INTRODUCTION
1.0 GENERAL INFORMATION
1.1 UNPACKING & INSPECTION
1.2 FREIGHT DAMAGE
1.3 MATERIAL MISSING OR DAMAGED
1.4 MECHANICAL INSTALLATION TOOLS
1.5 FOUNDATION INTERFACE
II ANTENNA SYSTEM ASSEMBLY
2.0 ANTENNA ASSEMBLY
2.1 FEED ASSEMBLY
III SATELLITE ALIGNMENT
3.0 ANTENNA POINTING
IV MAINTENANCE
4.0 MAINTENANCE OVERVIEW
4.1 REFLECTOR
4.2 MOUNT & REFLECTOR SUPPORT
4.3 FEED & FEED SUPPORT
4096-393
PRODELIN CORPORATION 1.2M Ku-BAND Rx/Tx SERIES 1134
4
SECTION I INTRODUCTION
1.0 GENERAL INFORMATION
This manual describes the assembly and installation of Prodelin's 1.2 meter antenna
system. The Prodelin 1.2 meter is a rugged and reliable mount which will operate in the
Ku-Band frequency with high efficiency and at the same time successfully withstand the
effects of the environment.
These instructions are listed by sections that cover all areas of assembly and installation.
Additional sections are included in the manual to provide information on antenna
alignment to the satellite and maintenance.
1.1 UNPACKING AND INSPECTION
The system containers should be unpacked and inspected at the earliest date to insure that
all material has been received and is in good condition. A complete packing list for each
major component is supplied.
1.2 FREIGHT DAMAGE
Any damage to materials while in transit should be immediately directed to the freight
carrier. He will instruct you on matters regarding any freight damage claims.
1.3 MATERIAL - MISSING OR DAMAGED
Any questions regarding missing or damaged materials that is not due to the freight
carrier should be directed to Prodelin's Customer Service Department at:
PRODELIN CORPORATION
4096-393
PRODELIN CORPORATION 1.2M Ku-BAND Rx/Tx SERIES 1134
5
1.4 MECHANICAL INSTALLATION TOOLS
The hardware supplied with this antenna system is U.S. SAE standard size and requires
SAE wrench sizes. However, the sizes have been chosen to allow use with compatibly
sized metric wrenches as shown in the table below.
HARDWARE SIZE SAE WRENCH SIZE METRIC WRENCH
SIZE MAXIMUM REC.
TORQUE
5/16” Bolt 1/2” 13 mm 12 ft-lbs
(1.66 kg-m)
1/2” Bolt 3/4” 20 mm 45 ft-lbs
(6.20 kg-m)
27/64” Screw 1/2” 13 mm Snug
5/8” Bolt 15/16” 24 mm 85 ft-lbs
(11.7 kg-m)
Also recommended for installation:
Inclinometer
Compass
Adjustable Wrench
1.5 FOUNDATION INTERFACE
The required interface from the foundation to the mount is 2-1/2" schedule 40 pipe (2.88"
or 7.3 cm O.D.). A suggested in-ground foundation is shown in Figure 1.
Also available from Prodelin, as options, are a kingpost pedestal mount and a
non penetrating mast mount.
4096-393
PRODELIN CORPORATION 1.2M Ku-BAND Rx/Tx SERIES 1134
6
SUGGESTED IN-GROUND FOUNDATION
NOTES:
1. 2 1/2” schedule 40 pipe should conform with ASTM A53.
2. All concrete should conform to building code standards and have a
minimum compressive strength of 3000 PSI at 28 days. (Per ACI-318-77)
3. Soil bearing capacity should be no less than 2000 PSF.
4-. Concrete should be poured against undisturbed soil.
5. Allow concrete 24 hours set time before installation of antenna.
6. The antenna should be properly grounded to meet applicable local codes.
7. Minimum depth as shown or extend to local frost line.
8. Foundation meets the design requirements as set forth by the uniform building code. (1982 edition)
(PRODELIN CORPORATION DOES NOT REPRESENT OR WARRANT THAT ANY PARTICULAR
DESIGN OR SIZE OF FOUNDATION IS APPROPRIATE FOR ANY LOCALITY OR EARTH STATION
INSTALLATION.)
Figure 1.
12.0
(30.5 cm)
30.0
(76.2 cm)
30.0
(76.2 cm)
SEE NOTE #7
45
SECTION A - A
2.5” (6.4cm) SCH 40 PIPE
2.88” OD (7.3 cm OD )
AA
4096-393
PRODELIN CORPORATION 1.2M Ku-BAND Rx/Tx SERIES 1134
7
PARTS LIST - 1.2M ANTENNA ASSEMBLY
ITEM NO. PART NO. DESCRIPTION QTY
1 0181-585 Canister Assembly 1
2 0181-584 Mount Assembly 1
3 VARIES 1.2M Reflector 1
4 0490-203 Elevation Rod 1
5 8104-007 2
6 8319-006 4
7 8031-008 2
8 8031-012 1
9 8201-041 4
10 8202-041 3
11 8101-009 3
1 / 2 - 13 Hex Nut
Hi - Lo Screw
5 / 16” x 1.50” Bolt
5 / 16” Flat Washer
5 / 16” Lock Washer
5 / 16” Hex Nut
5 / 16” x 1.00” Bolt
4096-393
PRODELIN CORPORATION 1.2M Ku-BAND Rx/Tx SERIES 1134
8
SECTION II
ANTENNA ASSEMBLY
CAUTION: During the assembly procedure, the sequence of instructions must be
followed. Do Not Tighten Any Hardware Until Instructed . Refer
to the antenna assembly parts list and the steps shown below.
2.0 ANTENNA ASSEMBLY
STEP 1:
STEP 2:
Mount Assembly
Azimuth Tube
A). Remove azimuth tube from mount assembly.
B). Set azimuth tube and hardware aside.
Mount Assembly A). Insert 5 / 16” hardware ( items: 7,9,10, 11)
thru hole on mount assembly as shown.
Repeat on opposite side.
[ 7 ] [ 9,10,11 ]
4096-393
PRODELIN CORPORATION 1.2M Ku-BAND Rx/Tx SERIES 1134
9
STEP 3;
STEP 4:
STEP 5:
Remove
Remove A). Remove rotation bolt, washer & lock washer
and set aside.
B). Remove [1] 1 / 2” jam nut.
Canister
Assembly
Azimuth Rod
A). Slide azimuth tube ( from Step. 1 ) onto
azimuth rod.
B). Replace 1 / 2” jam nut ( from Step. 3 ) back
onto azimuth rod.
Azimuth Rod
Azimuth Tube
1 / 2” Jam Nut
A). Place the canister assembly onto mast pipe.
B). Orient the canister assembly approximately
towards the center of the satellite orbital arc
to within +/- 15 .
C). Securely tighten [8] canister screws.
D). Tighten [8] lock nuts against canister.
To Satellite (within +/- 15 )
Canister Assembly
Mast Pipe
Table des matières
Autres manuels prodelin Antenne
prodelin
prodelin 3.8M Manuel utilisateur
prodelin
prodelin 1183 series Manuel utilisateur
prodelin
prodelin 1251 Manuel utilisateur
prodelin
prodelin 4096-247 Manuel utilisateur
prodelin
prodelin TIER II Manuel utilisateur
prodelin
prodelin 1132 series Manuel utilisateur
prodelin
prodelin 1381 Manuel utilisateur
prodelin
prodelin 1135 Series Manuel utilisateur
prodelin
prodelin C-Band Rx/Tx Manuel utilisateur
prodelin
prodelin 1132 series Manuel utilisateur
Manuels Antenne populaires d'autres marques
Alfa Network
Alfa Network APA-L01 Manuel utilisateur
Naval
Naval PR-422CA Manuel utilisateur
Feig Electronic
Feig Electronic ID ISC.ANTH200/200 Series Manuel utilisateur
TERK Technologies
TERK Technologies TV44 Manuel utilisateur
Directive Systems & Engineering
Directive Systems & Engineering DSE2324LYRMK Manuel utilisateur
HP
HP J8999A Manuel utilisateur
CommScope
CommScope CMAX-OMFX-43M-I53 Manuel utilisateur
Ramsey Electronics
Ramsey Electronics DAP25 Manuel utilisateur
COBHAM
COBHAM SAILOR 800 VSAT Manuel d'utilisation et d'entretien
Trango Systems
Trango Systems AD900-9 Manuel utilisateur
Steren
Steren ANT-100 Manuel utilisateur
Proxim
Proxim 5054-PA-23 Manuel utilisateur