Procentec Atlas 101-800110 Manuel utilisateur

Atlas

User Manual

Safety Guidelines

This manual contains notices which you should observe to ensure your own personal safety, as well as to

protect the product and connected equipment. These notices are highlighted in the manual by a warning sign

and are marked as followed according to the level of danger:

Draws your attention to important information on handling the product, a particular part of the

documentation or the correct functioning of the product.

Warning

This device and its components may only be used for the applications described in this manual and only in

connection with devices or components that comply with Industrial Ethernet interfaces.

This product can only function correctly and safely if it is transported, stored, set up, installed, operated and

maintained as recommended. Atlas is a CE class A product. In a domestic environment it may cause radio

interference in which case the user may be required to take adequate measures.

Warranty

Warranty is void if you open Atlas.

Qualified Technicians

Only qualified technicians should be allowed to install and work with this equipment. Qualified technicians are

defined as persons who are authorized to commission, to ground, to tag circuits and systems in accordance

with established safety practices and standards. It is recommended that the technicians carry a Certified

PROFINET Installer or Certified PROFINET Engineer certificate.

Disclaimer of Liability

We have checked the contents of this manual as much as possible. Since deviations cannot be precluded

entirely, we cannot guarantee full agreement. However, the content in this manual is reviewed regularly and

necessary corrections will be included in subsequent editions. Suggestions for improvements are welcome.

in any form or by any means, electronic, mechanical, photocopying, recording or otherwise, without the prior

written permission of the publisher.



Important information

Purpose of the Manual

This user manual provides information how to work with Atlas.

Support

In case of a defective product or unanswered questions, please get in contact with the support department:

Recycling and Disposal

The parts of the Atlas can be recycled.

“WARNING, BATTERY INSIDE; Battery may explode if mistreated. Do not disassemble or dispose of

in fire. Dispose product according to the instructions"

For further information about environment-friendly recycling and the procedure for the disposing of your old

equipment, please contact:

Document Updates

You can obtain constantly updated information on PROCENTEC products on the Internet at

www.procentec.com

T: +31-(0)174-671800

F: +31-(0)174-671801

E: support@procentec.com

PROCENTEC

Klopperman 16

2292 JD WATERINGEN

The Netherlands

T: +31-(0)174-671800

F: +31-(0)174-671801

E: info@procentec.com



Table of contents

Important information........................................................................................... 3

1. Product description ....................................................................................... 7

1.1 Introduction.......................................................................................................................................7

1.2 Your benefits .....................................................................................................................................7

1.3 Product features ................................................................................................................................7

1.4 System requirements ........................................................................................................................7

2. Quick Start ..................................................................................................... 8

3. Installation instructions ................................................................................. 9

3.1 Location .............................................................................................................................................9

3.2 Position ..............................................................................................................................................9

3.3 Power supply .....................................................................................................................................9

3.4 Ethernet connections ......................................................................................................................10

3.5 Client IP settings ..............................................................................................................................10

4. Web interface .............................................................................................. 11

4.1 Terminology and definitions............................................................................................................11

5. Prevent SSL warnings................................................................................... 13

5.1 Making the Atlas accessible using one of its official names ............................................................13

5.2 Installing the PROCENTEC root certificate.......................................................................................14

5.2.1 For Chrome......................................................................................................................................14

5.2.2 For Internet Explorer .......................................................................................................................14

6. Dashboard ................................................................................................... 15

6.1 System buttons................................................................................................................................15

6.2 Dashboard organization ..................................................................................................................17

6.3 Customize Dashboard......................................................................................................................17

7. User administration ..................................................................................... 18

7.1 Default users....................................................................................................................................19

7.2 Password best practice....................................................................................................................20

8. Setup Wizard ............................................................................................... 21

9. Topology ...................................................................................................... 22

9.1 Visual views .....................................................................................................................................22

9.1.1 Galaxy view......................................................................................................................................22

9.1.2 Tree view .........................................................................................................................................23

9.1.3 Custom view ....................................................................................................................................23

9.2 Graph search ...................................................................................................................................24

9.3 Device types in the Topology view ..................................................................................................24

9.4 Device status indicators in the Topology view ................................................................................26

9.5 Link indicators in the Topology view ...............................................................................................26

9.6 Protocol indicators in the Topology view ........................................................................................27

9.7 Device details...................................................................................................................................27

9.8 Link details .......................................................................................................................................29

10. Q-Factor....................................................................................................... 30

10.1 Multiple Q-Factors...........................................................................................................................30

11. Traffic Light.................................................................................................. 31

11.1 Traffic light state explained .............................................................................................................31

11.2 Traffic light triggers..........................................................................................................................31

12. Device list..................................................................................................... 32

12.1 Table customization ........................................................................................................................32

12.2 Available columns............................................................................................................................33

13. Trending....................................................................................................... 36

14. Report.......................................................................................................... 37

15. OPC UA ........................................................................................................ 38

16. E-mail Notifications...................................................................................... 38

17. Settings ........................................................................................................ 39

17.1 General tab ......................................................................................................................................39

17.2 User tab ...........................................................................................................................................39

17.3 Date & time .....................................................................................................................................40

17.4 Ethernet (office) & Ethernet (factory) .............................................................................................40

17.5 Network monitoring ........................................................................................................................41

17.6 Email 41

17.7 System .............................................................................................................................................42

17.8 Updates ...........................................................................................................................................42

17.9 About 43

18. License manager.......................................................................................... 43

19. Updating the firmware ................................................................................ 44

20.Resetting the device to factory defaults...................................................... 45

20.1 Using the hardware reset button ....................................................................................................45

20.2 Using the Settings in the web interface...........................................................................................45

21. Firewall settings........................................................................................... 46

22. Technical specifications ............................................................................... 47

23. Order codes ................................................................................................. 49

24. Certificates................................................................................................... 50

25. Sales offices and distributors....................................................................... 51

26. About PROCENTEC....................................................................................... 56

27. Notes ........................................................................................................... 57

1. Product description

1.1 Introduction

PROCENTEC’s Atlas is the solution for monitoring and diagnosing Ethernet networks, where innovative

simplicity and predictive capabilities are desired. The tool is perfect for preventing unexpected and expensive

downtime within industrial Ethernet networks.

PROCENTEC’s Atlas provides unique insight in your networks health and topology. With PROCENTEC Atlas

operators and engineers can easily detect problems and find their causes within your network. This prevents

costly down times.

The ease of use and clear overview makes this an ideal solution for the complete understanding of networks,

always and anywhere. Atlas is a compact device, that can be installed on a DIN rail and plugged in to the

network. Atlas does not require additional and time-consuming software installations on the PC. You can get all

the information using a custom designed web application. All the information Atlas gives, can be viewed on the

central, customizable dashboard page.

1.2 Your benefits

•Ease of use

•Use of Industrial Ethernet

•Topology

•Standalone device, 24/7 available

•Safe use

•Customizable dashboard

•Resistant to all environmental factors

•Easy to install via DIN rail

•No software required

1.3 Product features

•Network Topology

•Customizable dashboard

•Network Quality Factor

•Alarms

•Not vendor or protocol specific

1.4 System requirements

Atlas runs on any browser-enabled computer; the interface is fully web based.

HTML5 and JavaScript must be supported by the browser.

The minimum version requirements for web browsers are:

•Chrome version 46 or higher

•Edge version 25 or higher

•Firefox version 42 or higher

•Internet Explorer version 11 or higher

•Safari version 5 or higher

2. Quick Start

This checklist lists all the steps to a quick usage of Atlas.

Step: Instructions: See paragraph:

STEP 1 Install the device on a DIN rail. (3.1 and 3.2)

STEP 2 Connect the Office port to your laptop and the Factory port to the factory (3.4)

network.The factory side should NOT be connected to a mirror port of a

switch.

STEP 3 Connect the Atlas to a power supply. Wait until the green RDY LED is on. (3.3)

STEP 4 Set your laptops IP address to 192.168.1.1 and the netmask to (3.5)

255.255.255.0.

STEP 5 Open a web browser and go to https://192.168.1.10/. You will receive a (5.2)

warning about the certificate:

•Chrome users should click ‘ADVANCED followed by ‘Proceed ..’

•Internet Explorer/Edge users should click ‘Continue to this website ..’

STEP 6 Use user ‘admin’ and password ‘admin’ for the first login. (7)

STEP 7 Now complete the Setup Wizard but don´t change the settings of Office port (8)

yet.

STEP 8 Now setup the Office port in the Settings, unplug your laptop and connect

the Office port to the office network.

The Atlas is now operational. From here you can change settings, layout and behavior of the Atlas. If

connected to a factory network, it will start scanning and gathering information.

3. Installation instructions

3.1 Location

Atlas can be installed anywhere in a non-hazardous / non-Ex area that complies with IP 20 (DIN 40 050) and the

specified temperature range of -20 o to +60 o Celsius. Do not install the Atlas in a humid or dusty environment.

To comply with UL certification regulations, in ambient temperatures higher than 55oC or 131oF it is mandatory

to install the Atlas in an industrial installation cabinet with the “HOT HOUSING” warning label visible during

operation.

“WARNING, HOT HOUSING. When in use at an ambient temperature higher than

55oC or 131oF, the housing of the Atlas will be hot. Do not touch the housing!”

To comply with UL certification regulations the Atlas is to be used at altitudes not exceeding 2000m and in non-

tropical climate regions only.

3.2 Position

Atlas can only be installed on a horizontal 35mm DIN rail

with the front plates facing forward (see Figure 1 for an

example). In this position the generated heat of the

module can escape through the grid in the top of the

housing. It is also easier to read the status LEDs. Do not

install the Atlas in any other position, this could lead to

overheating of the device. Power supply

The Atlas contains a 3-pin screw type power connector on

the front.

The layout is as follows:

1 = - (upper pin)

2 = + (middle pin)

3 = SH (lower pin)

The power supply must comply with the following

specifications described in chapter:

•Voltage: 12 .. 24 VDC

•Wire diameter: < 2.5 mm2

For more information about the power supply see chapter

22 Technical specifications.

After the power has been connected, the Atlas will boot up. This process can take up to 90 seconds. When it is

booted, the green RDY LED will go on. You will see the Network Status LED blink yellow as long as the Setup

Wizard has not been completed and a measurement has

not been started.

Fig

ure 1 – Atlas mounted on a 35mm DIN rail

3.3 Ethernet connections

The Atlas has two physical network interfaces named Office and Factory. The networks are not connected with

each other one-on-one. The scanning, measuring and reporting of the network does not occur on the Office

side, only on the Factory side.

The Atlas may be connected anywhere in the Factory network. A mirror port is not required. In fact, a mirror

port is not recommended for the Atlas, as the Topology will not be accurate with a mirror port.

Please note: the web interface can be reached on the Office and the Factory network IP range. So it does not

matter where you are connected, as long as you have set the correct IP range and netmask settings of your

laptop/client network card. You will only be able to scan and see the devices connected to the Factory

network, not the Office network.

Pointers about the IP-address configuration:

In case your office and factory share the same (sub)network you should NOT connect and configure the Office

port. Just make sure that the default Office IP-address doesn’t exists on your network and uses a non-existing

subnet. In case your company network does use the 192.168.1.0/24 subnet, please change the IP-address to be

part of a non-existing network, for example 192.168.100.10/24.

3.4 Client IP settings

Your laptop or desktop computer must be

set to the same IP address range as the

Atlas to be able to reach the web

interface. If you are using Windows and

want to use the default IP address of the

office side of Atlas, go to the ‘Network

Adapter Settings’ and enter the details as

shown in . For more advanced settings

contact your system administrator.

Factory network

Office network

Atlas

Example IP range: 192.168.8.x

Subnetmask: 255.255.252.0

Example IP range: 10.0.16.x

Subnetmask: 255.255.254.0

Figure 2 - Atlas connected to office and factory network

Figure 3

- IP settings

Table des matières

Manuels Équipement de diagnostic populaires d'autres marques

Mindray

Mindray M7Vet Guide de démarrage rapide

Autel

Autel MaxiProgrammer 201 Manuel utilisateur

TEXA

TEXA TMD2 Manuel utilisateur

Autel

Autel MaxiIM IM608 Manuel utilisateur

Sealey

Sealey BT2012 Manuel utilisateur

Diagnoptics

Diagnoptics Age Reader Manuel utilisateur

LAUNCH TECH

LAUNCH TECH X-431 PRO5 Manuel utilisateur

Hella Gutmann

Hella Gutmann Mega macs X Manuel utilisateur

Foxwell

Foxwell I80TS Manuel utilisateur

KaVo

KaVo 3D eXam Manuel utilisateur

ATEQ

ATEQ VT46 Manuel utilisateur

Hella Gutmann

Hella Gutmann mega macs X Manuel utilisateur

Autel

Autel MaxiFlash VCMI Manuel utilisateur

Qiagen

Qiagen QIAcube Connect MDx Manuel utilisateur

Alber

Alber BDSU Manuel utilisateur

St. Jude Medical

St. Jude Medical QUANTIEN Manuel utilisateur

Bosch

Bosch DCU 100 Manuel utilisateur

Launch

Launch CNC-602A Manuel utilisateur