PROALL G Series Manuel utilisateur

ProAll

Mobile

Mixer

Operator’s Manual

G Model

MX05001 3 March 2022

Rev.1

MX05001

Rev. 1 3 March 2022

5810 - 47 Avenue, Olds, Alberta, Canada, T4H 1V1

Esupport@proallinc.com | P403-335-9500 | F403-335-9560

 MX05001 
i 
Rev. 1 3 March 2022 
 
Table of Contents 
 
Model Number...................................................................................1-3 
Serial Number ....................................................................................1-3 
 
Safety Decals......................................................................................2-1 
Safety Alert Symbol............................................................................2-4 
Signal Words ......................................................................................2-4 
Safety .................................................................................................2-5 
General Safety....................................................................................2-5 
Operating Safety ................................................................................2-6 
Maintenance Safety...........................................................................2-6 
Hydraulic Safety .................................................................................2-6 
Storage Safety....................................................................................2-7 
Transport Safety.................................................................................2-7 
Tire Safety ..........................................................................................2-7 
Safety Signs ........................................................................................2-8 
How to Install Safety Signs:.........................................................................2-8 
 
 
Mixer Controls ...................................................................................4-1 
Mix Auger Paddle........................................................................................4-2 
Operator Control.........................................................................................4-2 
Operating Keypad .......................................................................................4-3 
Valve Locations ..................................................................................4-6 
 
Traditional Gunite Production Calibration Procedure.......................5-1 
Step 1: Cement Output per Conveyor Count..............................................5-1 
Step 2: Counts per Unit Volume of Mix ......................................................5-1 

MX05001 
ii 
Rev. 1 3 March 2022 
Step 3: Sand Weight per Count...................................................................5-2 
Results.........................................................................................................5-2 
Computer Gunite Production Calibration Procedure ........................5-2 
Step 1: Cement Output per Auger Count....................................................5-2 
Step 2: Counts per Unit Volume of Mix ......................................................5-3 
Step 3: Gate Calibration..............................................................................5-3 
Fibre Feeder Calibration ....................................................................5-4 
 
Principle of Operation........................................................................6-1 
Mix Batching ......................................................................................6-1 
Aggregate...........................................................................................6-1 
Aggregate Control Gate ..............................................................................6-1 
Cement Powder .................................................................................6-2 
Mix Auger...........................................................................................6-2 
Drop-Away Bottom Mat..............................................................................6-3 
Auger Bearing..............................................................................................6-3 
Mix Bowl .....................................................................................................6-3 
Auger Top Drive ..........................................................................................6-4 
Fibre Feeder.......................................................................................6-5 
Setting up to Pour..............................................................................6-6 
Pouring...............................................................................................6-7 
Clean up and Preparation for Transport............................................6-7 
Chain Oiler..........................................................................................6-8 
Tarp....................................................................................................6-9 
Tarp Control ................................................................................................6-9 
 
Maintenance......................................................................................7-1 
Speed Sensor......................................................................................7-1 
Take Up Bearing.................................................................................7-1 
Oil Specifications................................................................................7-1 
Cleanliness ..................................................................................................7-1 
Hydraulic System.........................................................................................7-1 

 MX05001 
iii 
Rev. 1 3 March 2022 
Minimum Requirements for Replacement Oil............................................7-1 
Hydraulic Oil Filter..............................................................................7-2 
Wear Plates........................................................................................7-2 
Service................................................................................................7-3 
Lubrication and Maintenance Points.................................................7-4 
Lubrication and Maintenance Frequency..........................................7-9 
Electrical Distribution Box................................................................7-10 
Bolt Torque ......................................................................................7-11 
 
 
 
 

MX05001

1-1

Rev. 1 3 March 2022

1. Introduction

Congratulations, you have chosen the world’s

finest and most reliable mobile mixer. You are

now part of the world-wide ProAll International

family, operating successfully in 36 countries.

Your ProAll Mobile Mixer, manufactured by

ProAll International Inc. will meet, or exceed

your concrete requirements. ProAll International

represents over 30 years of experience in

mobile, volumetric, continuous batching; both as

a concrete supplier and as a mixer manufacturer.

Now introducing dry mix mixers for Gunite

operations.

Years of experience have helped us develop and

engineer a mobile mixer that will give many

years of dependable and profitable service.

This manual provides operating and

maintenance procedures that are critical to the

profitable and successful operation of your

ProAll Mobile Mixer. Operation and

maintenance of your new mixer in accordance

with this manual will assure you of long and

trouble-free service.

Keep this manual handy for frequent reference

and pass it on to new operators or owners. Call

your local dealer or distributor if you need

assistance, information, or additional copies of

the manual. Contact your dealer for a complete

listing of parts.

OPERATOR ORIENTATION - The directions left,

right, front, and rear, as mentioned throughout

the manual, are as seen from the direction of

travel.

MX05001

1-2

Rev. 1 3 March 2022

ALWAYS give the SERIAL NUMBER when ordering

parts or requesting service or other information.

The serial number plate is located where

indicated. Please mark the number in the space

provided for easy reference.

Model Number:

Serial Number:

Plate 1. Model and Serial Number Plate

MX05001

1-3

Rev. 1 3 March 2022

Model Number

G95

#####

▪Last 5 Digits of Serial Number

▪1

Standard

Cement Hopper

Configuration

▪B

113 Cubic Foot (Steel)

133 Cubic Foot (Steel)

Cement Hopper Size

▪00

No Extensions

26 in. Frame Extension

▪G95

8.50 Cubic Meter

9.50 Cubic Meter

Base Model Capacity

Serial Number

120

10950

▪Manufacturer’s Serial Number Code

▪X

Swing system: not required

▪69/137

Conveyor length indicating the

number of cross bars on the chain

▪VA

12 Volt Operating System

24 Volt Operating System

▪X

Water tank: not required

▪T9

Mixing Auger:

12in body, 9in screw x 96 in.

▪2

Tandem Pump

▪K

System: Electric / Hydraulic

Hydraulic

Table des matières

Manuels Véhicule utilitaire populaires d'autres marques

Polaris

Polaris ACE 900 SP Manuel utilisateur

TrailMax

TrailMax T-12-UR Manuel utilisateur

Floe

Floe Cargo Max 9.5-73 Manuel utilisateur

Toro

Toro 07277 Workman 2110 Manuel utilisateur

Taylor-Dunn

Taylor-Dunn B0-050-00 Manuel

Toro

Toro 133-7128 Manuel utilisateur

Taylor-Dunn

Taylor-Dunn ET 3000 Manuel utilisateur

Kayo

Kayo S70 Manuel utilisateur

Range Road

Range Road RR608 Manuel utilisateur

Landoll

Landoll 900D Series Manuel utilisateur

pronovost

pronovost PUMA-10000 Manuel utilisateur

SSI SCHAEFER

SSI SCHAEFER WEASEL LITE Manuel utilisateur

Club Car

Club Car TURF 272 2005 Manuel

Toro

Toro 07059TC Manuel utilisateur

Cushman

Cushman Turf Truckster 84069 Manuel utilisateur

BERG

BERG Large Trailer Manuel utilisateur

Cub Cadet

Cub Cadet Big Country 641 Manuel utilisateur

Westward

Westward Go-4 XTR Manuel utilisateur