PrimeScales PS-IN202SS Manuel utilisateur

Version 2012.11

PS-IN202SS / 202

Weighing Indicator

User Manual

PS-IN202 (SS) Indicator - 1 -

Contents

FRONT AND REAR VIEW OF THE INDICATOR

CHAPTER 1 CONNECTIONS

1.1 WHAT'S IN THE BOX

1.2 CONNECTING TO THE WEIGH PLATFORM

1.3 CONNECTION TO A PRINTER OR COMPUTER

1.4 CONNECTION TO THE POWER SUPPLY

CHAPTER 2 CONFIGURATION

2.1 SET UP (“P”) MENU

2.2 Setup Menu Chart

2.3 Exiting the setup menu

2.4 USER (“S”) MENU

2.5 User Menu Chart

2.6 Setup Menu Descriptions

2.7 User Menu Descriptions

CHAPTER 3 CALIBRATION

3.1 Zero Calibration

3.2 Span Calibration

3.3 View calibration values

3.4 Key-in zero calibration value

3.5 Key-in span calibration value

CHAPTER 4 OPERATION

4.1 Display

4.2 Display Details

4.3 Keyboard

4.4 Weighing

4.5 Tare Function

PS-IN202 (SS) Indicator - 2 -

Front and Rear View of the Indicator

FIG1 and FIG 2 show the front and rear view of the indicator.

FIG 1.1

FIG 2.2

FIG 2

PS-IN202 (SS) Indicator - 3 -

Chapter 1

Connections

1.1 WHAT'S IN THE BOX

The box contents are as follows:

Indicator

Power Adaptor (for PS-IN202 only)

Wall Mount Bracket

15 ft cable

This Manual

The indicator is supplied with a 15 ft shielded load cell cable to interface to weigh platform’s

load cell(s) or junction box.

1.2 CONNECTING TO THE WEIGH PLATFORM

a. Plug the 4-pin connector into the signal port on the rear panel of the indicator (for PS-

IN202SS you need to mount the bare wires onto the board directly). Wire the bare wires and

shield to the weigh platform’s load cell(s) or junction box using the color codes shown below:

RED: +Excitation

BLACK: -Excitation

GREEN: +Signal

WHITE: -Signal

b. Alternatively, instead of using the shielded load cell cable supplied, a cable may be

assembled with the pin assignments shown in FIG 3:

FIG 3

1.3 CONNECTION TO A PRINTER OR COMPUTER

The indicator contains a standard full duplex RS-232 serial port, designed for connection to

either a PC or a serial printer as shown in FIG 4.

FIG 4

PS-IN202 (SS) Indicator - 4 -

The indicator can be directly interfaced to a serial printer, remote display or computer

communication cable (not included) using the D-SUB9 serial port connector.

Pin No. Pin Name

1.4 CONNECTION TO THE POWER SUPPLY

The indicator comes with an external AC adapter (PS-IN202SS comes with cable directly

connected to power outlet). Connect the AC adapter to the indicator then plug the mains plug

into a standard wall outlet.

PS-IN202 (SS) Indicator - 5 -

Chapter 2

Configuration

The indicator contains two main setup menus:

The Setup (“P”) menu

This configures the indicator to the weigh platform

The User (“S”) menu

This configures the serial communication port and enables some user options.

The Setup and User menus consist of several menu selections, each with its own sub-menu.

To set up the indicator, first select the appropriate menu mode. Keys [UNIT], [ZERO],

[TARE] and [PRINT] become direction navigators (as indicated by the arrows above them)

to move around the menus and the [NET/GROSS] key is used to save or SET the

selections.

2.1 SET UP (“P”) MENU

a. Switch off the indicator.

b. On the rear panel, move the Calibration/Setup Switch to the “Setup” position. Left is

calibration mode, right is weighing mode.

c. Switch on the indicator. The indicator will display “P 1” to indicate that it is in Setup P

menu mode.

Use the direction keys to navigate around in the Setup Menu Chart.

a. To move to a new “P” heading, use the [TARE] (left) or [PRINT] (right) key to navigate the

Setup Menu Chart.

b. To move to the selection level, press the [ZERO] (down) key once. The current saved

selection is shown.

c. To view the available selections for the current “P” heading, use the [TARE] (left) or

[PRINT] (right) key to navigate through the selection field.

d. To save a new selection, press the [NET/GROSS] (Set) key .To exit without saving, press

the [UNITS] (up) key to return to the current “P” heading.

e. Repeat Steps 1 through 4 until the Setup Menu is programmed.

PS-IN202 (SS) Indicator - 6 -

FIG 5

2.2 Setup Menu Chart

FIG 6

The User (“S”) sub-menus appear when scrolling left or right from the “P” menu. Some

selections shown are not available on some versions.

2.3 Exiting the setup menu

a. Switch off the indicator.

b. On the rear panel, move the Calibration/Setup Switch to the “Calibration” position. Left is

calibration mode, right is weighing mode.

c. Switch on the indicator. The display will go through a digit check then go into Normal

Operating mode. All front panel keys will now return to their normal mode of operation.

2.4 USER (“S”) MENU

PS-IN202 (SS) Indicator - 7 -

a. Enter the Setup (“P”) menu.

b. Use the right or left direction keys to navigate the Setup (“P”) menu until the

indicator shows ” S 1”. Use the direction keys to navigate the User Menu Chart.

c. To move to a new “S” heading, use the [TARE] (left) or [PRINT] (right) key to navigate the

User Menu Chart.

d. To move to the selection level, press the [ZERO] (down) key once. The current saved

selection is shown.

e. To view the available selections for the current “S” heading, use the [TARE] (left) or

[PRINT] (right) key to navigate the selection field.

f. To save a new selection, press the [NET/GROSS] (Set) key .To exit without saving, press

the [UNITS] (up) key to return to the current “S” heading.

g. Repeat Steps 2 through 5 until the User Menu is programmed.

FIG 7



PS-IN202 (SS) Indicator - 8 -



2.5 User Menu Chart

FIG 8

2.6 Setup Menu Descriptions

This section provides a more detailed description of the selections found in the Setup Menu

Chart. Factory-set defaults are shown in bold with a checkmark (√).

NAME/CODE DESCRIPTION CODE/VALUE

FS Divisions

Specifies number of full-scale graduations. Value should be consistent

with legal requirements and environmental limits on the useful system

resolution

500

1,500

2,500

4,000

6,000

10,000

20,000

40,000

1,000

2,000

3,000

5,000√

8,000

12,000

30,000

50,000

Span

Span Gain is related to the A/D integration time. The larger the span, the

higher the internal resolution, but the slower the update speed. Note that

the scale must be recalibrated whenever this parameter is altered. See

Appendix C for more information

80√

Zero Track

Band

Selects the range within which the scale will automatically zero. Note that

the scale must be in standstill to automatically zero. Selections are in

Display Divisions

0.5d√

PS-IN202 (SS) Indicator - 9 -

Zero Range

Selects the range within which the scale may be zeroed. Note that the

indicator must be in standstill to zero the scale

100%√

1.9%

Motion Band

Sets the level at which motion is detected by comparing the present

display update with the previous one. If motion is not detected for two

seconds or more, the scale is in standstill and can process a Print or Zero

command. Maximum value varies depending on the local regulations

0.25d

1d√

10d

Digital Filter

Averages weight readings to produce higher stability. The higher the filter

setting the greater the stability but the slower the indicator’s response

time. Choose SLOW unless a very fast response is needed

FAST

SLOW√

Overload

Limit

Selects the desired formula which determines the point at which the

indicator shows overload. All selections are based on the primary unit

selected in P8

“FS” = Full Scale in primary units

FS+ 2%√

FS + 1d

FS + 9d

Default Unit

Selects the primary base unit to be used in the calibration process. Also

the default unit for normal operation.

“1” = primary unit is lb “2” = primary unit is kg

1√

Display

Divisions

Determines the desired weight increments. Value should be conformed to

legal requirements.

1√

P10

Decimal Pt

Determines the location of the decimal point 0√

0.00

0.0000

0.0

0.000

P11

Zero

Calibration

Places the indicator into the zero calibration routine. Scrolling down with

the [ZERO] key one level begins the procedure

Press [ZERO] key to

begin sequence

P12

Span

Calibration

Places the indicator into the span calibration routine. Scrolling down with

the [ZERO] key one level begins the procedure

Press [ZERO] key to

begin sequence

P13

View

Calibration

Actuates the function that allows the user to view both the zero and span

calibration value. The values displayed in this function are valid only after

calibration (P11 and P12) have been successfully completed. Scrolling

down with the [ZERO] key one level begins the procedure

Press [ZERO] key to

begin sequence

P14

Key-in Zero

Allows the user to key in a known zero calibration value in case of memory

loss in the field. Scrolling down with the [ZERO] key one level begins the

procedure

Press [ZERO] key to

begin sequence

P15

Factory

Reset

This sub menu will reset all parameters in the “P” and “S” menu to the

default setting. USE WITH CAUTION!

Press [ZERO] key twice

to begin sequence

Ce manuel convient aux modèles suivants

Table des matières

Langues :

Manuels Accessoires populaires d'autres marques

Hillco

Hillco 2810 Manuel utilisateur

Siemens

Siemens QSA2700D Manuel de l'opérateur

Contours

Contours ZY024 Manuel utilisateur

Saivod

Saivod VS621 Manuel utilisateur

Virtuox

Virtuox VirtuCLEAN 2.0 Manuel utilisateur

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manuel utilisateur

Z-Wave

Z-Wave HSD-200Z Manuel utilisateur

turck

turck FMX-IM-2UPLI63FX Manuel utilisateur

Decagon Devices

Decagon Devices 10HS Manuel utilisateur

UPPAbaby

UPPAbaby Cup Holder Manuel utilisateur

Elko

Elko SmartSensor Leakage Wireless Manuel utilisateur

Grizzly

Grizzly H8371 Manuel utilisateur

Panasonic

Panasonic HG-T Series Manuel utilisateur

IFM Electronic

IFM Electronic Efector 250 Series Guide de référence

DigiDesign

DigiDesign 888/24 I/O Manuel utilisateur

PROZIS

PROZIS QUAY Manuel utilisateur

patagonia

patagonia PSI Vest Manuel utilisateur

SFC Energy

SFC Energy EFOY GO! Manuel utilisateur