Primera Accent Manuel utilisateur
062204-510887-(03)
Connectivity Guide
© 2004 All rights reserved.
Optical Disc Laminator
XL/Pro
MAX
510887.qxd 6/24/2004 9:58 AM Page i
Notices:The information in this document is subject to change without notice. NO WARRANTY OF
ANY KIND IS MADE WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO,
THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. No liability is assumed for errors contained herein or for incidental or consequential
damages in connection with the furnishing, performance, or use of this material. This document
contains proprietary information, which is protected by copyright. All rights are reserved. No part of
this document may be photocopied, reproduced, or translated into another language without prior
written consent.
Trademark Acknowledgments: Windows is a registered trademark of Microsoft Corporation. All
other trademarks are the property of their respective owners.
Printing History
Edition 3.0, #510887, © Copyright 2004, All rights reserved.
ii
510887.qxd 6/24/2004 9:58 AM Page ii
iii
Table of Contents
Optical Disc Laminator Guide .....................................................................................1
A. Unpacking and Inspection ...............................................................................1
B. Installing the Laminator Software Driver......................................................1
C. Connecting the Laminator to Your Duplicator .............................................3
D. Creating Discs with Your Duplicator MAX in Primo ..................................7
E. Connecting the Laminator to Your Duplicator XL/Pro ..............................7
Stand-Alone Mode.............................................................................................8
Full Production Mode .....................................................................................11
F. Troubleshooting ...............................................................................................15
G. Technical Support ............................................................................................15
510887.qxd 3/14/2004 11:06 AM Page iii
iv
510887.qxd 3/14/2004 11:06 AM Page iv
Optical Disc Laminator Connectivity Guide 1
Optical Disc Laminator Connection Guide
THANK YOU…
Thank you for purchasing the Optical Disc Laminator
Connectivity Kit. This kit will allow you to use your Optical
Disc Laminator in conjunction with the Pro, XL and MAX
versions of Optical Disc Duplicators. This guide will explain
the connection of the Laminator to these systems, the
installation of software and the running of disc jobs.
A. UNPACKING AND INSPECTION
While unpacking your Laminator Connectivity Kit make sure
that all supplied accessories are included with your kit. The
following items are included:
•Laminator Stand
•Software Installer Disc
•USB Cable
•6-Pin Mini Circular Cable (Pro/XL Stand only)
•Warranty Statement, Manual and other documentation.
B. INSTALLING THE LAMINATOR SOFTWARE DRIVER
When using the Laminator with a Primera Technology Disc
Duplicator it will be necessary to install a driver and other
software updates. This driver will allow the PC to control the
functions of your Laminator. Because your Disc Laminator is a
plug-and-play device, do not connect the Laminator's USB
cable to the PC until instructed to do so by the installer. The
driver is installed as follows:
a. This installer will reboot your system so make sure all
applications are closed. Insert the Software Driver Install
disc into your PC's CD-ROM drive
b. The Installer Quick Start program should launch. If it does,
proceed to step c. If not, please follow these steps:
•Click the Start button in the lower left hand side of the
screen, and then select My Computer from the menu.
•Double-click Install.exe.
c. Choose the Duplicator you are using, either Duplicator
XL/Pro or Duplicator MAX.
d. You will now be prompted to install software and drivers
that will allow you to print, record and laminate
unnatended. Click Next to install the update.
510887.qxd 3/14/2004 11:06 AM Page 1
2 Optical Disc Laminator Connectivity Guide
e. Make certain the Laminator has been plugged into power
and turned on.
f. Connect the Laminator to your PCs USB port using the
USB cable included with this kit.
g. Select "Install Software Automatically" and click Next.
510887.qxd 3/14/2004 11:06 AM Page 2
Optical Disc Laminator Connectivity Guide 3
h. You may see a notice like the one shown here stating that
the Accent Disc Laminator has not passed Windows Logo
Testing. Click the Install Anyway button to continue
installing the printer driver for your Laminator.
Once the driver has finished installing, click the Finish button.
This will install an update to your PrimoDVD software and
will reboot your system.
C. CONNECTING THE LAMINATOR TO YOUR DUPLICATOR
MAX
Your Laminator connects easily to a DuplicatorMAX allowing
for hands-free printing, recording and laminating of Optical
Discs. This configuration does require you to remove one bin
bringing total capacity from 400 to 300 discs. The optional
DuplicatorMAX Laminator Stand is shown here:
MAX Stand
Adjustable Screws
510887.qxd 3/14/2004 11:06 AM Page 3
4 Optical Disc Laminator Connectivity Guide
The following steps describe in detail how to connect the
Laminator to your DuplicatorMAX:
a. Connect the Laminator Stand to the left hand side of the
DuplicatorMAX as shown:
b. Remove the Input Bin closest to the Laminator Stand to
make room for the Laminator's disc tray.
c. Place the Laminator on the stand using the Locating Pegs
to align the Laminator properly. Please note that there are
two sets of locating holes on the underside of the
Laminator. Be sure to use the smaller set of holes which
are located toward the front, or tray side of the Laminator.
When placed on the front-most set of holes, the Laminator
will sit a little further back on the stand.
d. Connect your Laminator to the PC using the provided
USB Cable.
e. The Laminator must now be aligned with the
DuplicatorMAX Picker Mechanism. This is done as
follows:
1) If the Laminator Tray is not in the "OUT" position,
press the Laminate Button on the Laminator to eject
the tray. Make certain the DuplicatorMax has been
connected to the computer and is on and ready to use.
2) Press the Sequence Button on the front of the
DuplicatorMax until the picker mechanism is
positioned over a bin containing discs.
510887.qxd 6/24/2004 9:58 AM Page 4
Optical Disc Laminator Connectivity Guide 5
3) Press the Pick Button on the front of the DuplicatorMax
to pick a disc.
4) Launch PrimoDVD.
5) From the Main Application Screen click Robotics then
Options.
6) Enable the Use Laminator checkbox.
7) Click the button labeled Move to Laminator
(Calibrate). This will move the Picker Mechanism to
the Laminator Tray position.
8) Lower the disc to the Laminator Tray Position
as follows:
a) Press and hold the Sequence and Pick buttons
simultaneously for 5 seconds to enter calibration
mode. The LEDs on the front of the
DuplicatorMAX will flash back and forth indicating
that the unit is in calibration mode.
Press Simultaneously
Until LEDs Toggle
510887.qxd 6/24/2004 9:58 AM Page 5
6 Optical Disc Laminator Connectivity Guide
b) While the LEDs are flashing, press the Pause
button. The Picking Mechanism will lower to the
Laminator Tray Position.
c) Adjust the Laminator Tray forward and back by
loosening the adjusting screws located towards the
front of the stand.
d). For left-to-right adjustment, nudge the Picker
Mechanism left by pressing the Pause Button or
nudge it right by pressing the Sequence Button.
e) Once the Picking Mechanism and Disc are
perfectly aligned press the Pick Button to end
calibration
Press Pause to Lower
Mechanism to Laminator
Tray Position
End Calibration
Nudge Picking Mechanism Right
(Counter Clockwise)
Nudge Picker Mechanism Left
(Clockwise)
510887.qxd 1/21/2004 7:35 PM Page 6
Autres manuels pour Accent
1
Ce manuel convient aux modèles suivants
2
Table des matières
Autres manuels Primera Plastifieuse
