Prime Design FEA-0015 Manuel utilisateur

PRIME DESIGN, A SAFE FLEET BRAND ▪ Address: 1689 Oakdale Avenue #102, West St Paul, Minnesota 55118

Toll Free: 1.8.PRIME.RACK ▪ Fax: 651-552-1799 ▪ Email: [email protected] ▪ Website: www.primedesign.net

Prime Design Limited Warranty. Seller’s sole and exclusive warranty (and Buyer’s sole and exclusive remedy and Seller’s entire liability for any breach thereof) with respect to the Goods is set forth in the Limited Warranty document available at primedesign.net/warranty-liability

(the “Prime Design Limited Warranty”).

▪

TM & © 2020 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6427889, 6764268, 6971563, 8991889, 9415726, 9506292, 9481313, 9776476, 9796340, 10470565, 10486608 AND OTHER PATENTS PENDING

FEA-0015 ASSEMBLY INSTRUCTIONS–PACKAGING CONTENTS

1—Front Drive Shaft .............................................. (Qty 1)

B Version, 23.75”

CONTENTS OVERVIEW

3—Rear Drive Shaft............................................... (Qty 1)

Right Hand, B4 Version, 46.00”

2—Connecting Bar................................................. (Qty 1)

36.00”

4—Handle Latch Assembly ................................... (Qty 1)

Right Hand

(the “Prime Design Limited Warranty”).

▪

FEA-0015 ASSEMBLY INSTRUCTIONS–PACKAGING CONTENTS

5—HKT-8162.......................................................... (Qty 1)

Modular Rotation Hardware Kit

Anti-Seize (1X)

Lubricant (1X)

Clevis Pin (1X)Cotter Pin (1X)

M8 x 50MM (4X) ⅜" x 2.25" (2X)

1.00" Sealing

Stickers (10X)

M8 Lock Nut (4X) ⅜" Lock Nut (2X) ⅜" Flat Washer (4X)" Flat Washer (8X)

(the “Prime Design Limited Warranty”).

▪

2/7

FEA-0015 ASSEMBLY INSTRUCTIONS–RIGHT DRIVE SHAFT

RIGHT DRIVE SHAFT

ASSEMBLY SEQUENCE

REAR DRIVE SHAFT

1.1

1.2

1.3

Torque to

90 in-lbs

CYLINDER HARDWARE

2.1

2.2

NOTE: Crossbars and RH Rotation feature

are shown for illustrative purposes only.

Crossbars and Rotations are not included

with this Drive Shaft feature, and must be

purchased separately.

NOTE: Flow Control Screw

faces toward vehicle rear

NOTE: Loosen the Cylinder Flow Control Screw (Fig.

C) as needed to allow movement for Steps 2.1-2.2.

When nished with Cylinder Hardware, tighten the

Flow control Screw all the way closed then turn back

open 1½ turn.

(the “Prime Design Limited Warranty”).

▪

Approximate

positioning

Note: To prevent damage to

the Release Latch, do not

rotate the lever beyond the

position shown in Figure A.

Figure A

FEA-0015 ASSEMBLY INSTRUCTIONS–RIGHT DRIVE SHAFT

HANDLE LATCH ASSEMBLY

3.1

Remove and retain

for Step 3.5

3.1

Remove and retain

for Step 3.5

3.2

Remove and retain

for Step 3.4

3.3 As shown in Figure A, lightly pull the Release Latch outward

prior to setting the Latch Assembly onto the Drive Shaft.

3.4 Slide into Handle

Clamp Body

3.7

Torque to 90 in-lbs

3.5 Apply Anti-Seize Compound to the Hardware removed during

Step 3.1, then install Hardware into Handle Clamp Body.

Handle must engage

the Latch as shown.

3.6 Position the Handle Latch Assembly with

the Rotation in its full resting position.

The Handle must engage the Crossbar

Interlock before nal tightening.

(the “Prime Design Limited Warranty”).

▪

*If using the optional

5’ Connecting Bar

FEA-0015 ASSEMBLY INSTRUCTIONS–RIGHT DRIVE SHAFT

CONNECTING BAR FRONT DRIVE SHAFT

4.1

5.1

5.3

4.2

5.2

CONNECTING BAR VARIATIONS

The 3' Connecting Bar can be adjusted to

t Crossbar spacings of 4'–6'.

The optional 5' Connecting Bar can be

adjusted to t Crossbar spacings of 6'–8'.

Assemble the Connecting Bar to the

Drive Shafts according to your model's

Crossbar spacing.

5.4

Torque to

90 in-lbs

(the “Prime Design Limited Warranty”).

▪

FEA-0015 ASSEMBLY INSTRUCTIONS–RIGHT DRIVE SHAFT

CONNECTING BAR FASTENERS

DRIVE SHAFT SEALING

8.1

8.2

Apply Silicone Sealant

(not supplied) to ends

of Connecting Bar

CYLINDER ADJUSTMENT

Adjust the Cylinder Flow

Control Screw to allow

approximately 3 seconds

time for the ladder to glide

down when operating the

loaded Ladder Rack.

NOTE: This completes the right hand assembling of FEA-0015.

For left side Drive Shaft assembly procedures, see FEA-0016

Assembly Manual.

If applicable, refer to your next FEA Assembly Manual.

If completed, refer back to your FBM Assembly Manual, and

resume assembling at Step 3.1.

WARNING: Failure to position the Crossbars as shown in your

FBM Assembly Manual may result in damage to the sliding

door and/or ladder rack.

USAM-FEA0015-US01 Rev-A 0419

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Prime Design Accessoires automobiles

Prime Design

Prime Design FEA-0022 Manuel utilisateur

Prime Design

Prime Design FEA-0001 Manuel utilisateur

Prime Design

Prime Design AluRack AR-2000 Manuel utilisateur

Prime Design

Prime Design FEA-0004 Manuel utilisateur

Prime Design

Prime Design VRR3-FT31G-ST Manuel utilisateur

Prime Design

Prime Design AR1929 Manuel utilisateur

Prime Design

Prime Design AXC Manuel utilisateur

Prime Design

Prime Design AR1221 Manuel utilisateur

Prime Design

Prime Design UVX 201 Manuel utilisateur

Prime Design

Prime Design URX-001-E Manuel utilisateur

Prime Design

Prime Design DEPLOYPRO LOCK N GO Manuel utilisateur

Prime Design

Prime Design ACC-8000 Manuel utilisateur

Prime Design

Prime Design VRI3-FT31B Manuel utilisateur

Prime Design

Prime Design VBB-226 Manuel utilisateur

Prime Design

Prime Design UXR-001-E Manuel utilisateur

Prime Design

Prime Design WORKPRO ASH-8034 Manuel utilisateur

Prime Design

Prime Design FBM-1019 Manuel utilisateur

Prime Design

Prime Design FEA-0019 Manuel utilisateur

Prime Design

Prime Design Safe Fleet FBM-1028-BLK Manuel utilisateur

Prime Design

Prime Design CBR-0010 Manuel utilisateur

Prime Design

Prime Design FBM-1026-BLK Manuel utilisateur

Prime Design

Prime Design AR1937 Manuel utilisateur

Prime Design

Prime Design FBM-1061 Manuel utilisateur

Prime Design

Prime Design FBM-1009 Manuel utilisateur

Manuels Accessoires automobiles populaires d'autres marques

James Baroud

James Baroud Odyssey Manuel utilisateur

Motorola

Motorola i50sx Manuel utilisateur

Yakima

Yakima 9MM STANDARD BIKE MOUNT Manuel utilisateur

Feniex

Feniex T3 Manuel utilisateur

Renault

Renault 77 11 423 180 Manuel utilisateur

Kia

Kia E8300-4D000 Manuel utilisateur

Brink

Brink 756843 Manuel utilisateur

Whispbar

Whispbar K085W Manuel utilisateur

v.link

v.link CI-VL2-PC-HSD Manuel utilisateur

Viking

Viking Stack-Rack Guide de configuration rapide

Aries

Aries 203015 Manuel utilisateur

Choetech

Choetech AT0005 Manuel utilisateur

ZZ2

ZZ2 ZZAIR-PRO Manuel utilisateur

Holman

Holman 4A80L Manuel utilisateur

Thule

Thule 2075 Manuel utilisateur

Motorola

Motorola T325 Manuel utilisateur

TAUBENREUTHER

TAUBENREUTHER 16-3950 Guide d'installation

DV8

DV8 FBJL-02 Manuel utilisateur