PRG BAD BOY 02.9812.0001C Manuel utilisateur

USER MANUAL

000

pot Lum

Sii

twar

rsi

n 1.

AutoPar™, Bad Boy™, Mbox Extreme™, PRG Series 400™, Virtuoso®, Virtuoso® DX, Virtuoso® DX2, and Visionary™3D

are trademarks of Production Resource Group, LLC, registered in the U.S. and other countries.

All other brand or product names which may be mentioned in this manual are trademarks or registered trademarks of their respective companies.

This manual is for informational use only and is subject to change without notice. Please check www.prg.com for latest version.

PRG assumes no responsibility or liability for any claims resulting from errors or inaccuracies that may appear in this manual.

Bad Boy™ Spot Luminaire User Manual

Version as of: December 15, 2009 | PRG part number: 02.9812.0001C

Production Resource Group

Dallas Office

8617 Ambassador Row, Suite 120

Dallas, Texas 75247

www.prg.com

Bad Boy™ Spot Luminaire User Manual

FOREWORD

02.9812.0001C i

Compliance Notice

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1) This

device may not cause harmful interference, and 2) This device must accept any interference received, including

interference that may cause undesired operation.

Conforms to:

UL STD 1573

Certified to:

CAN/CSA STD E598-1

CAN/CSA STD E598-2-17

Safety Notice

It is extremely important to read ALL safety information and instructions provided in this manual and any

accompanying documentation before installing and operating the products described herein. Heed all cautions

and warnings during installation and use of this product. Safety symbols used throughout this manual are as

follows:

GENERAL INFORMATION PERTAINING TO PROTECTION AGAINST ELECTRICAL SHOCK, FIRE,

EXPOSURE TO EXCESSIVE UV RADIATION, AND INJURY TO PERSONS CAN BE FOUND BELOW.

WARNING: INSTRUCTIONS FOR CONTINUED PROTECTION AGAINST FIRE

1. PRG luminaires have been designed for use only with specific lamps. Note lamp type before replacing.

Installing another type of lamp may be hazardous.

2. PRG luminaires may be mounted on any type of surface as long as mounting instructions are followed. See

instructions detailed in this manual.

3. Replace fuses with same type and rating only.

4. Minimum distance from head to any flammable object is 2m.

WARNING: INSTRUCTIONS FOR CONTINUED PROTECTION AGAINST ELECTRICAL SHOCK

1. PRG luminaires are designed for dry locations only. Exposure to rain or moisture may damage luminaire.

2. Disconnect power before servicing any PRG equipment.

3. Servicing to be performed by qualified personnel only.

FCC

CAUTION advising of potential damage to product.

WARNING advising of potential injury or death to persons.

BAD BOY™ SPOT LUMINAIRE USER MANUAL

ii 02.9812.0001C

WARNING: INSTRUCTIONS FOR CONTINUED PROTECTION AGAINST EXPOSURE TO EXCESSIVE

ULTRAVIOLET RADIATION

1. PRG luminaires may use an HID type lamp which produces UV radiation. DO NOT look directly at lamp.

2. It is hazardous to operate luminaires without complete lamp enclosure in place or when lens is damaged.

Lenses or UV shields shall be changed if they have become visibly damaged to such an extent that their

effectiveness is impaired.

WARNING: INSTRUCTIONS FOR PROTECTION AGAINST INJURY TO PERSONS

1. Exterior surfaces of the luminaire will be hot during operation. Use appropriate safety equipment (gloves,

eye protection, etc.) when handling and adjusting hot equipment and components. Service and maintenance

should be performed only by qualified personnel as determined by the high pressure lighting fixture

manufacturer.

2. Arc lamps generate intense heat. Disconnect power and allow lamp to cool for 5 minutes before relamping.

3. Arc lamps emit ultraviolet radiation which can cause serious skin burn and eye inflammation. Additionally,

arc lamps operate under high pressure at very high temperatures. Should the lamp break, there can exist a

danger of personal injury and/or fire from broken lamp particles being discharged.

4. The lamp shall be changed if it has become damaged or thermally deformed.

5. If lamp is touched with bare hands, clean lamp with denatured alcohol and wipe with lint-free cloth before

installing or powering up the luminaire.

6. Serious injury may result from the generation of ozone by this lamp system. A proper means of venting must

be provided.

FOREWORD

02.9812.0001C iii

Notes de sécurité

Avant de procéder à l’installation des produits décrits dans ce guide et de les mettre en marche, il est

extrêmement important de lire TOUS les renseignements et TOUTES les directives de sécurité contenues dans ce

guide ainsi que toute documentation jointe. Tenir compte de tous les avertissements et suivre toutes les

précautions pendant l’installation et l’utilisation de cet appareil.

Les symboles de sécurité utilisés dans ce guide sont les suivants :

CETTE SECTION CONTIENT DES INFORMATIONS GÉNÉRALES POUR SE PROTÉGER CONTRE LES

DÉCHARGES ÉLECTRIQUES, LES INCENDIES, L’EXPOSITION EXCESSIVE AUX RAYONS UV ET

TOUT AUTRE ACCIDENT POUVANT ENTRAÎNER DES BLESSURES.

AVERTISSEMENT: RISQUE D’ EXPLOSION.

1. Le service et le maintenance ne devront être assurés que par des personnes qualifiées comme precisé par le

frabricant des lampes à haute pression.

2. Des vêtement de protection et les procédures précisées dans le manuel du frabricant doit être fournies.

AVERTISSEMENT: RÉGLAGE DES LAMPES

1. Chaleur intense. Débrancher le matériel et laisser refroidir pendant 5 minutes avant de rallumer.

2. Risque l’incendie. N’utilise que des Philips MSR Gold™ FastFit Lamp.

AVERTISSEMENT: DIRECTIVES POUR SE PROTÉGER CONTRE UNE EXPOSITION EXCESSIVE AUX

RAYONS UV

1. Risque d’explosion en cas de radiation ultraviolet imprantes.

2. Ne pas intervener en l’absence de confinement de la lampe en place ou quand la lentille est abîmée.

AVERTISSEMENT: DIRECTIVES POUR SE PROTÉGER CONTRE LES ACCIDENTS POUVANT ENTRAÎNER

DES BLESSURES

1. Chaleur intense. Eviter tout contact avec des personnes ou des tissues. Attention, de graves blessures

peuvent résulter de production d’ozone par cette lampe. Un système de ventilation adapté doit être fournies

2. La température de surface = 300.c

La temperature de l’ambiance = 50.c

3. Ne convient pas pour un usage résidential.

4. Utilisable seulement dans les locaux secs.

ATTENTION Ce symbole annonce que l’appareil risque d’être endommagé.

AVERTISSEMENT Ce symbole annonce qu’il y a risque d’accident grave ou même fatal.

BAD BOY™ SPOT LUMINAIRE USER MANUAL

iv 02.9812.0001C

Revision History

This manual has been revised as follows:

Version Release Date Notes

BASIC February 27, 2009 Software version 1.0. Initial release.

A May 21, 2009 Software version 1.1. Updated menu system, spin

mode values, and troubleshooting chart. Added

Bypass Calibration, Gobo Set Zero Position, and

Software Update procedures.

B July 9, 2009 Added additional hanging instructions, photometrics,

and power consumption chart. Updated various

menu and operational details.

C December 15, 2009 Software version 1.5. Updated menu system and

maintenance cleaning procedures. Added Group

Test instructions, Comm Loss setting, new control

channel options, and optional follow spot operation.

TABLE OF CONTENTS

02.9812.0001C v

Table of Contents

Introduction

About This Manual .......................................................................................................................... 1

Additional Documentation............................................................................................................... 1

Customer Service ............................................................................................................................. 2

Gobo Art Submission Guidelines .................................................................................................... 3

Chapter 1. Description

Features

Overview.......................................................................................................................................... 6

Features...................................................................................................................................... 6

Components

Included Items.................................................................................................................................. 7

Replacement Items and Accessories................................................................................................ 7

Major Components and Controls ..................................................................................................... 8

Chapter 2. Installation

Power and Data Cabling Requirements

Power ............................................................................................................................................. 10

Data ................................................................................................................................................ 10

DMX512 Cables...................................................................................................................... 10

DMX512 Male Termination Connector .................................................................................. 12

Ethernet Cables........................................................................................................................ 12

Installation Procedures

Unpacking and Attaching Hanging Brackets................................................................................. 13

Standard Hang................................................................................................................................ 14

Vertical "Yoke Out" Hang.............................................................................................................. 16

Standing Position ........................................................................................................................... 18

Connecting Power and Data........................................................................................................... 19

Power Up and Basic Setup Procedures

Powering Up the Luminaire........................................................................................................... 21

Comm LED Operation ............................................................................................................ 22

Bypassing Calibration.................................................................................................................... 22

Setting a Starting Address.............................................................................................................. 23

DMX Comm............................................................................................................................ 23

Ethernet (Art-Net) Comm........................................................................................................ 24

Starting the Lamp........................................................................................................................... 25

Configuring Comm Loss Setting ................................................................................................... 26

Configuring Universe, Comm, and Other Options ........................................................................ 26

BAD BOY™ SPOT LUMINAIRE USER MANUAL

vi 02.9812.0001C

Accessory Options

Follow Spot Operation................................................................................................................... 27

Enabling Pan/Tilt Free Mode .................................................................................................. 28

Chapter 3. Operation

Menu System

Using the Menu Touchscreen......................................................................................................... 30

On-Board Battery .................................................................................................................... 31

Menu System Overview................................................................................................................. 32

Menu Details.................................................................................................................................. 33

Home Screen ........................................................................................................................... 33

Lamp Screen............................................................................................................................ 34

Configuration Screen............................................................................................................... 34

Pan/Tilt Screen ........................................................................................................................ 35

Information Screen .................................................................................................................. 35

Communication Screen ........................................................................................................... 36

Status Screen ........................................................................................................................... 36

Test Screen .............................................................................................................................. 37

DMX512 Operation

Channel Mapping........................................................................................................................... 38

Wheel Control................................................................................................................................ 39

Control Channels............................................................................................................................ 41

Timing Channels ............................................................................................................................ 42

Channel Functions................................................................................................................... 42

Timing Channel Mapping........................................................................................................ 42

Zoom Tables................................................................................................................................... 46

Gobo Set Zero Position.................................................................................................................. 46

Chapter 4. Troubleshooting and Maintenance

Troubleshooting

Troubleshooting Guide................................................................................................................... 48

Errors.............................................................................................................................................. 49

Testing

Test Screen ..................................................................................................................................... 52

Mechanical Test ............................................................................................................................. 53

Group Test...................................................................................................................................... 54

Software Update

Software Update Using LumLoader Application .......................................................................... 55

Software Crossload ........................................................................................................................ 57

Equipment Handling

Proper Lamp Servicing and Operation........................................................................................... 58

TABLE OF CONTENTS

02.9812.0001C vii

Routine Maintenance

Removing the Head Covers ........................................................................................................... 59

Removing the Aft Cover................................................................................................................ 61

Removing the Enclosure Covers.................................................................................................... 62

Cleaning the Head Electrostatic Filters.......................................................................................... 63

Cleaning the Enclosure Intake Filters ............................................................................................ 64

Cleaning the Luminaire Exterior.................................................................................................... 65

Cleaning the Lenses ....................................................................................................................... 66

Cleaning Gobo, Color and Dimmer Wheels .................................................................................. 69

Replacing the Lamp ....................................................................................................................... 70

Adjusting the Lamp........................................................................................................................ 72

Replacing a Gobo........................................................................................................................... 73

Replacing a Designer Color Filter ................................................................................................. 76

Appendix A. Technical Specifications

Bad Boy Spot Luminaire................................................................................................................ 80

Bad Boy Road Case ....................................................................................................................... 82

AC Line Current / Power vs. Voltage ............................................................................................ 83

Photometric Data............................................................................................................................ 83

Narrow Zoom .......................................................................................................................... 84

Medium Zoom......................................................................................................................... 85

Wide Zoom.............................................................................................................................. 86

Logarithmic Beam Illuminance Comparison .......................................................................... 87

Appendix B. Glossary

Glossary of Terms ................................................................................................................... 90

BAD BOY™ SPOT LUMINAIRE USER MANUAL

viii 02.9812.0001C

Notes

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels PRG Mettre en lumière

PRG

PRG ReNEW Manuel utilisateur

Manuels Mettre en lumière populaires d'autres marques

Guangzhou Yinhe Lighting&Sound Equipment Factory

Guangzhou Yinhe Lighting&Sound Equipment Factory NE-204 Manuel utilisateur

LIVARNO home

LIVARNO home 375304 2101 Instructions originales

Cameo

Cameo CLQS40WW Manuel utilisateur

Leviton

Leviton Ellipsoid 5/50 Manuel utilisateur

Monacor

Monacor img Stage Line PARL-56PDX/CR Manuel utilisateur

Vector

Vector SL3AKV Manuel utilisateur

Quantum

Quantum Q262 Manuel d'exploitation

Philips

Philips Vari-lite VL3015LT Manuel utilisateur

EUROSPOT

EUROSPOT C51 Manuel utilisateur

DTS

DTS MINI BRICK ARC Manuel utilisateur

Federal Signal Corporation

Federal Signal Corporation VISIBEAM II Manuel

ACME

ACME LED-MS350B Manuel utilisateur

EuroLite

EuroLite Akku flat light 1 Manuel utilisateur

Commercial Electric

Commercial Electric SPTM-1401 Manuel utilisateur

Vision & Control

Vision & Control SLB-500-W5K7-P-SL Manuel utilisateur

Teknik

Teknik FLEXI Manuel utilisateur

Craftsman

Craftsman CMXLSB10 Manuel utilisateur

EuroLite

EuroLite LED SLS-144 UV Floor Spot Manuel utilisateur