Premium PES610 Manuel utilisateur
Instruction Manual Built-in Electric Cook top
Manual de Instrucciones Estufas de
Empotrar Eléctricas
Model: PES610
Working Principle
Product Introduction
Dear customer,
Thank you for purchasing the ceramic cooker hob.
Our product can serve you many years to your satisfaction.
Please read this instructions manual carefully before using and installation.
Keep it in a good place after reading for future reference.
Thank you again for your purchase of the ceramic cooker hob, and wish
you to enjoy the pleasure brought about by it.
of cuisine demands because of resistance wire heating, mechanical
computerized control, really the optimal choice for modern families.
The ceramic cooker hob centers on customers and adopts personalized
design. The hob has safe and reliable performances, making your life
comfortable and enabling to fully enjoy the pleasure from life.
2
resistance wire heating, and adjust the output power by the power regulation
with the mechanical control knobs
PES610
The mechanical ceramic cooker hob can meet different kinds
The mechanical ceramic cooker hob directly employs
PES610
3
Safety
Residual heat indicators
After using the hob, waste heat remains in the heating area. The
indicator lamp will light up, warning to be away from the heating area.
Installation
Selection of installation equipment
Drill holes on the table surface according to the sizes shown in the drawing.
For the purpose of installation and use, a minimum of 50 mm space shall
be preserved around the hole.
Be sure the thickness of the table surface is at least 30mm. Please select
heat-resistant table material to avoid larger deformation caused by the heat
radiation from the hotplate.
As shown in Figure (1)
50mm mini
50mm mini 50mm mini
50mm mini
560mm
490mm
High temperature protection
The temperature sensor mounted on the radiant electric the temperature
inside the cooker from time to time. When an excessive temperature is
detected, the cooking plate will be directly disconnected and stop power
output.
Note: The safety distance between the ceramic hob and the cupboard
above the hotplate should be at least 760mm.
Air intake
Figure (2)
mini 50 mm
mini 20 mm
4
Under any circumstances, make sure the ceramic cooker hob is well
ventilated and the air inlet and outlet are not blocked.
Ensure the ceramic cooker hob is in good work state. As shown in
Figure (2)
Fix the hob on the table by screw four brackets on the bottom of hob
(see picture) after installation. Adjust the bracket position to suit for
different table top thickness.
screw
bracket
base
screw hole
mini 760 mm
5
Cautions
The ceramic cooker hob must be installed by qualified personnel
or technicians. We have professionals at your service. Please
never conduct the operation by yourself.
The ceramic cooker hob shall not be mounted to cooling equipment,
dishwashers and rotary dryers.
The ceramic cooker hob shall be installed such that better heat radiation
can be ensured to enhance its reliability.
The wall and induced heating zone above the table surface shall
withstand heat.
To avoid any damage, the sandwich layer and adhesive must be
resistant to heat.
A steam cleaner is not to be used.
A board is must to be installed underneath the hob.
4.
5.
1.
2.
3.
6.
7.
If the cable is damaged or to be replaced, the operation must be
carried out by the after-sale agent with dedicated tools to avoid
any accidents.If the appliance is being connected directly to the
mains an omnipolar circuit-breaker must be installed with a
minimum opening of 3mm between contacts. The installer must
ensure that the correct electrical connection has been made and
that it is compliant with safety regulations.
The cable must not be bent or compressed.
The cable must be checked regularly and replaced by authorised
technicians only.
Figure (3)
Power line connection
The socket shall be connected according to the relevant standard
blue
green-yellow
N2 N1 L2 L1
grey
brown
black
220-240V
220-240V
blue
green-yellow
N L
grey
brown
black
220-240V
PE
PE
connect to the main power supply connect to the main power supply
220-240V 2+2N~ 220-240V~
or connected to a single-polecut-out.30 minimum supply.
The method of connection is shown in Figure (3):
The ceramic cooker hob appearance
Schematic diagram of the control panel
6
Power
regulating knob
Power cord
Ceramic glass
knob
High temperature
Indicator lamp
7
The power of each heating zone are shown as follow:
Left rear Right rear
1200W 1800W 1800W
Left front
Right front
Heating zone
Power
Operation Instructions:
1200W
Instructions for Use
Put the pot in the center of the heating zone.
After the power supply is connected,put the pot on the center of the ceramic
plate,Turn the knob clockwise or anticlockwise to turn on the hob.
Shut down : After using,please turn the knob to "OFF",the hob will stop
heating.
High temperature indicator lamp:
When the glass plate is too hot,the high temperature indicator lamp will light
up,don't touch the glass plate until the indicator lamp goes out.
Safety Reminding and Maintenance
Adedicated power protection
air swith protection air switch
must be incorporated in the
fixed wiring in accordance
with the wiring rules.
Never use the ceramic cooker
hob in high temperature
environments such as near a
gas stove or kerosene stove.
Do not put any detergents or
flammable materials in the
equipment installed under the
ceramic cooker hob.
Never wash the induction
cooker with water directly to
avoid danger.
Keep electrical appliance out
of reach from children or
inform person. Do not let them
use the appliances without
supervision.
After being used for a long
time, the corresponding
heating zone of the ceramic
cooker hob is till hot. Never
touch the ceramic surface to
avoid burning.
If the supply cord is damaged
, it must be replaced by the
manufacturer, its service agent
or similarly qualified persons
in order to avoid a hazard.
8
Never have the ceramic
cooker hob to work without
food inside, otherwise its
operational performance may
be affected and danger may
happen.
For sealed foods such as
canned goods, please do not
heat them before opening their
covers so as to avoid any
dangers of explosion due to
heating expansion.
If the surface is cracked, swith
off the appliance to avoid the
possibility of electric shock.
Do not place rough or uneven
appliances, which may
damage the ceramic surface.
Metallic objects such as
knives, forks,spoons and lids
should not be placed on the
hotplate since they can get
hot.
DISPOSAL: Do not dispose this
product as unsorted municipal
waste. Collection of such waste
separately for special treatment
is necessary.
Clean the ceramic cooker hob
on a regular basis to prevent
foreign matters from entering
the fan thus influencing the
normal operation.
Indoor use only.
9
Light
Clean with hot water and
damp sponge
Cleaning sponge
Accumulation
of dirt
Clean with hot water and
abrasive sponge
Special cleaning
sponge for ceramic
glass
Rings and lime
crumbles
Sweetmeat,
melt aluminum
or plastics
Apply white vinegar to the
polluted zone, then wipe it
dry with soft cloth or a
special article available in
local markets
Use a scraper suitable for
ceramic glass (to protect
glass, a silicon product is
preferred) to remove
residuals
Special adhesive for
ceramic glass
Special adhesive for
ceramic glass
Cleanness and Maintenance
You can easily clean the surface of the ceramic cooker hob if
following the methods given in the table.
Hint: please disconnect power before the cleaning.
Type of contam-
ination Method of cleaning Articles used for
cleaning
Children should be supervised to ensure that they do not play with the appliance.
3. A steam cleaner is not to be used.
1. This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction concerning use of the
appliance by a person responsible for their safety.
2. If the supply cord is damaged, it must be replaced by the manufacturer, its service
agent or similarly qualified persons in order to avoid a hazard.
5. The appliance is not intended to be operated by means of an external timer or
separate remote-control system.
4. After use, switch off the hob element by its control and do not rely on the pan
detector.
Special DecIaration
All the contents in this material have been subjected to careful check.
For any mistake and omission in printing or misunderstanding of the
contents,the company keeps the right of interpretation.
Addition:any technical improvement will be placed in the revised
manual without notice;for product appearance and color is according
to the actual one
10
Maintenance Service Warranty
For any failure of the product, please contact the special
maintenance department or the customer service center.
1. There is a year’s guarantee with the our brand ceramiccooker
hob.
2. The period of warranty shall start from the date on which the invoice
is issued.
3. Any one of the following cases is without the warranty:
Damages caused by improper use, storage and maintenance of
the consumer.
Damages caused by unauthorized disassembly and repair in the
maintenance department not designated by the company.
Model of invoice and model of product maintained are not in
conformity or are altered.
Valid invoice can not be presented.
Damages caused by force majeure.
Using the ceramic cooker hob for commercial purposes.
Table des matières
Langues :
Autres manuels Premium Plaque
