Premise FLS1 Series Manuel utilisateur
1
INSTALLATION INSTRUCTIONS
IMPORTANT
Before assembling your fixture,
please make sure that you carefully
read through this instruction sheet.
Consider having your fixture installed
by a qualified licensed electrician.
FLS1 SERIES
ULTRA SLIM
FLOOD LIGHTS
FLS1-304KN-1 |FLS1-304TR-1
FLS1-504TR-1 |FLS1-804TR-1
GENERAL INFORMATION
This LED Flood Light uses the latest in
solid state lighting technology for
long life, low maintenance, and high
efficiency. The same as traditional
HID lighting. Suitable for use in the
following locations: ambient
temperature of -40°and wet
locations.
The fixtures can be installed using
two installation methods, dependent
on the model you purchased: via
junction box mount or direct surface
mounting.
For use with:
WHAT’S IN THE BOX
•LED ULTRA-SLIM FLOOD LIGHT FIXTURE
•2 X EXPANSION BOLTS
WHAT YOU’LL NEED
•SCREWDRIVER / POWER DRILL
•WIRE CUTTERS
•IP65 J-BOX
•WIRING SUPPLIES AS SPECIFIED BY
ELECTRICAL CODE
PREMISE LED Inc.
80-86 Carrier Drive
Toronto, ON Canada
M9W 5R1
PREMISELED.COM
To avoid the risk of fire, explosion, or electric shock, this product
should be installed, inspected, and maintained by a qualified
electrician only, in accordance with all applicable electrical codes.
Be certain electrical power is OFF before and during installation
and maintenance.
Make sure the supply voltage is the same as the rated luminaire
voltage.
Do not operate in ambient temperatures above those indicated
on the luminaire nameplate.
WARNING
2
INSTALLING VIA TRUNNION MOUNT
For Trunnion Mount models:
1. Using the trunnion mount holes as a guide, mark
the installation points.
1. Use expansion bolts (included) to secure the fixture
onto the mounting surface at the marked
installation points.
3. Keep enough length wires to ensure adjusting
angle unhindered.
4. Connect wires into wiring terminal; white wire to
“Neutral” terminal, black wire to “Live” terminal,
green wire to “Ground” terminal.
Note: for 208V, connect second live wire to white wire.
5. Adjust the beam angle of the flood light to point in
the desired direction. Follow the recommended
torque (Nm) required based on fixture wattage.
6. Restore the electricity and check the operation of
your new lighting fixture.
10W
30W
50W
80W
Torque
(Nm) 1.8 8 8 8
WIRING DIAGRAM
3
INSTALLING VIA KNUCKLE MOUNT
For Knuckle Mount models:
1. Pull the connecting wire through the knockout of
the junction box.
1. Screw the fixture into the junction box and tighten
the mounting nut with a 30-gauge wrench.
3. Connect wires into wiring terminal; white wire to
“Neutral” terminal, black wire to “Live” terminal,
green wire to “Ground” terminal.
Note: for 208V, connect second live wire to white wire.
4. Adjust the beam angle of the flood light to point in
the desired direction. Follow the recommended
torque (Nm) required based on fixture wattage.
5. Restore the electricity and check the operation of
your new lighting fixture.
30W
Torque
(Nm) 8
WIRING DIAGRAM
Note: Knuckle mount is sized to fit a 1/2" NPT
Ce manuel convient aux modèles suivants
4
Table des matières
Autres manuels Premise Projecteur
Manuels Projecteur populaires d'autres marques
VIZULO
VIZULO Micro Martin Guide de l'utilisateur
EuroLite
EuroLite LED IP FL-100 SMD Manuel utilisateur
Cooper Wheelock
Cooper Wheelock XB12 Manuel utilisateur
Allen + Roth
Allen + Roth 17624-000 Manuel utilisateur
ADJ
ADJ 4 STAGE PAK Manuel utilisateur
Cooper Lighting
Cooper Lighting EGL91SW233 Manuel utilisateur
