Premier Mounts IPM-53 Manuel utilisateur
Installation Instructions Visit the Premier Mounts website at http://www.mounts.com
iPad™ IPM-530 Tabletop Stand and Wall Mount Installation Instructions
9531-056-061-00
Parts List
IPM-530
iPad™ Frame
(Qty 1)
3130 East Miraloma Avenue
Anaheim, CA 92806 USA
USA and Canada
Phone: 1.800.368.9700
Fax: 1.800.832.4888
Other Locations – Phone: (001).714.632.7100; Fax: (001).714.632.1044 ©Premier Mounts 2011
The IPM-530 tabletop stand and wall mount securely holds the Apple
iPad™ or iPad2™ (not included) in place and gives access to all
iPad™ controls and connections. Attach the removeable back plate to
the base, then rotate the mount for landscape or portrait placement.
The mounting base can be placed freely on a tabletop, or drilled into
it with wood screws. The base can also be mounted to a wood stud or
surface..
• All trademarks are the property of the respective trademark owners.
#8 x 1¼” Wood Screw
(Qty 4)
IPM-530 Mounting Base
(Qty 1)
Push-In Rivet
(Qty 4)
Step 1
Remove the back plate from the
iPad™ frame.
Step 2
Are you installing an original
iPad™ or iPad2™ to the
IPM-530?
If an original iPad™, remove
the corner felt pads on the
iPad™ frame. Then continue
to step 3.
If an iPad2™, continue to
step 3.
Remove if using original iPad™
Remove if using original iPad™
Step 3
➊Extend the arms of the iPad™
frame.
➋Insert the iPad™ in the iPad™
frame.
Each arm of the iPad™ frame
should t over a corner of the
iPad™.
Continue to Step 4 on page 2.
10-32 x ¼”
Flat Phillips Screw
(Qty 2)
Page 2 Visit the Premier Mounts website at http://www.mounts.com Installation Instructions
IPM-530
IPM-530 Installation Instructions (cont’d)
Step 5
Are you using the IPM-530 as a
tabletop or wall mount?
If tabletop mount, use two (2)
10-32 x ¼” at Phillips screws
to attach the back plate (pointed
side up) to the mounting base
(Figure 1).
If wall mount, use two (2)
10-32 x ¼” at Phillips screws
to attach the back plate (pointed
side down) to the mounting base
(Figure 2).
10-32 x ¼” Flat Phillips Screw
Step 4
➊Adjust the arms on the iPad™
frame so that the iPad™ ts
snuggly inside the mount (Figure
1).
➋Tighten the two (2) pre-installed
Phillips screws on the back of
the iPad™ frame to secure the
arms (Figure 2).
Mounting tab on IPM-530
Figure 1
Figure 2
Phillips screws
10-32 x ¼” Flat Phillips Screw
Step 6
Choose one of the following installation options:
• If freestanding tabletop mount, continue to Freestanding Tabletop
Installation below.
• If swivel tabletop mount, go to Swivel Tabletop Installation on page 3.
• If wood stud installation, go to Wood Stud Installation on page 3.
• If wood surface installation, go to Wood Surface Installation on page 4.
Freestanding Tabletop
Installation
➊Insert the iPad™ frame into
the back plate on the mounting
base.
➋Rotate the mount to the desired
landscape or portrait position.
➌Tighten the two (2) pre-installed
M4 x 16mm pan combo screws
on the sides of the back plate.
Figure 1
Figure 2
Installation Instructions Visit the Premier Mounts website at http://www.mounts.com Page 3
IPM-530 Installation Instructions (cont’d)
IPM-530
Swivel Tabletop Installation
➊Replace the bumpers on the
bottom of the mounting base
with four (4) push-in rivets
(Figure 1).
➋Determine where you want to
secure the mounting base.
➌Insert one (1) #8 x 1¼” wood
screw through a bottom screw
hole on the mounting base and
into the table (Figure 2).
➍Insert the iPad™ frame into the
back plate on the mounting base
(Figure 3).
➎Rotate the mount to the desired
landscape or portrait position.
➏Tighten the two (2) pre-installed
M4 x 16mm pan combo screws
on the sides of the back plate.
Figure 1
Figure 2
Push-in rivet
Wood screw
Figure 3
Wood Stud Installation
➊Determine where you want to
attach the mounting base to the
wood stud.
➋Insert two (2) #8 x 1¼” wood
screws through the bottom
screw holes on the mounting
base and into the stud
(Figure 1).
➍Insert the iPad™ frame into the
back plate on the mounting base
(Figure 2).
➎Rotate the mount to the desired
landscape or portrait position.
➏Tighten the two (2) pre-installed
M4 x 16mm pan combo screws
on the sides of the back plate.
Wood screw
Figure 1
Figure 2
Page 4 Visit the Premier Mounts website at http://www.mounts.com Installation Instructions
IPM-530
IPM-530 Installation Instructions (cont’d)
Wood Surface Installation
➊Determine where you want to
attach the mounting base to the
wood surface.
➊Remove the bumpers from the
bottom of the mounting base.
➋Insert four (4) #8 x 1¼” wood
screws through the corner holes
on the mounting base and into
the wood surface (Figure 1).
The corner holes are where the
bumpers used to be.
➍Insert the iPad™ frame into the
back plate on the mounting base
(Figure 2).
➎Rotate the mount to the desired
landscape or portrait position.
Wood screw
Figure 1
Figure 2
Technical Specications
.67
17.12
5.83
147.99
5.91
150
5.91
150
6.00
152.40
1.35
34.29
5.07
128.85
2.62
66.55
4.80
121.92
All measurements are in inches [millimeters].
Autres manuels Premier Mounts Accessoires pour tablettes
Manuels Accessoires pour tablettes populaires d'autres marques
Bretford
Bretford PowerRack 10 Manuel utilisateur
Brenthaven
Brenthaven EDGE 360 Manuel utilisateur
Fujitsu
Fujitsu Stylistic 3400 Manuel utilisateur
Heckler Design
Heckler Design WindFall STAND Manuel utilisateur
Kensington
Kensington KeyFolio SecureBack Manuel utilisateur
Xplore
Xplore Companion Keyboard Manuel utilisateur
Logitech
Logitech Ultrathin Manuel utilisateur
Infinite Peripherals
Infinite Peripherals INFINEA X MINI Manuel utilisateur
Trust
Trust Executive Folio Stand Manuel utilisateur
Manhattan
Manhattan 406017 Manuel utilisateur
Logitech
Logitech SLIM COMBO Manuel utilisateur
Logitech
Logitech AnyAngle iC1051 Manuel utilisateur