9
5. IMPOSTAZIONI
5.1 Impostazione della memoria
6 Setting
6.Setting
6.1 Memory Parameter Setting
Fast-Pack has 5 memory programs, press to
change during standby state, the memory number
T1 will change according.
During any Memory, holding down press then
press in 2 seconds, the “Temperature” of this
memory can be change.
Press till target temperature, the temperature
can be set from 90℃to 250℃.
press to confirm.
Press again, the “Keep-heat Time” of this
memory can be change.
Press till target time, the time can be set 3, 5, 8
and 10 seconds.
press to confirm.
Press again, the “CoolingDisplay” of this
memory can be change.
Press till target time, the time can be set 0, 3, 5
and 10 seconds.
press to confirm.
Page 12 / 26
Endo Gutta Pack ha 5 programmi, premere per cambiare programma
durante lo stato di standby, il programma T1 cambierà.
6 Setting
6.Setting
6.1 Memory Parameter Setting
Fast-Pack has 5 memory programs, press to
change during standby state, the memory number
T1 will change according.
During any Memory, holding down press then
press in 2 seconds, the “Temperature” of this
memory can be change.
Press till target temperature, the temperature
can be set from 90℃to 250℃.
press to confirm.
Press again, the “Keep-heat Time” of this
memory can be change.
Press till target time, the time can be set 3, 5, 8
and 10 seconds.
press to confirm.
Press again, the “CoolingDisplay” of this
memory can be change.
Press till target time, the time can be set 0, 3, 5
and 10 seconds.
press to confirm.
Page 12 / 26
Una volta selezionato il programma, tener premuto , poi per due
secondi, per poter cambiare la temperatura del programma.
Premere no alla temperatura desiderata, il range di temperatura sele-
zionabile è compreso tra 90°C e 250°C.
Premere per confermare la temperatura desiderata.
6 Setting
6.Setting
6.1 Memory Parameter Setting
Fast-Pack has 5 memory programs, press to
change during standby state, the memory number
T1 will change according.
During any Memory, holding down press then
press in 2 seconds, the “Temperature” of this
memory can be change.
Press till target temperature, the temperature
can be set from 90℃to 250℃.
press to confirm.
Press again, the “Keep-heat Time” of this
memory can be change.
Press till target time, the time can be set 3, 5, 8
and 10 seconds.
press to confirm.
Press again, the “CoolingDisplay” of this
memory can be change.
Press till target time, the time can be set 0, 3, 5
and 10 seconds.
press to confirm.
Page 12 / 26
Premere di nuovo per poter modicare il tempo di riscaldamento
(“Keep-heatTime”) del programma selezionato.
Premere no al tempo desiderato, che può essere di 3, 5, 8 e 10 s.
Premere per confermare.
6 Setting
6.Setting
6.1 Memory Parameter Setting
Fast-Pack has 5 memory programs, press to
change during standby state, the memory number
T1 will change according.
During any Memory, holding down press then
press in 2 seconds, the “Temperature” of this
memory can be change.
Press till target temperature, the temperature
can be set from 90℃to 250℃.
press to confirm.
Press again, the “Keep-heat Time” of this
memory can be change.
Press till target time, the time can be set 3, 5, 8
and 10 seconds.
press to confirm.
Press again, the “CoolingDisplay” of this
memory can be change.
Press till target time, the time can be set 0, 3, 5
and 10 seconds.
press to confirm.
Page 12 / 26
Premere di nuovo per poter modicare il tempo di raffreddamento
(“CoolingDisplay”) del programma selezionato.
Premere no al tempo desiderato, che può essere di 3, 5, 8 e 10 s.
Premere per confermare.
5.2 Impostazioni avanzate
6 Setting
6.2 Advanced Setting
During power off state, holding down press
then press to entry advanced setting, the
“AutoPowerOff” will appear on the display screen.
Press to adjust, the auto power off time can be
set 5, 10 and 15 minutes
press to confirm.
Press again, the “Beep Volume” can be
change, press to adjust, the “Beep Volume”
can be set 0, 1 and 2.
press to confirm.
Press again, the “RestoreSettings” can be
change, press to adjust, press to confirm.
NOTE
If choice “YES”, all the setting parameters will be
covered by factory settings.
Press again, confirm the setting need to save
or not, press to adjust, press to save and
power off.
Page 13 / 26
Quando lo strumento è spento, tenere premuto , poi per due
secondi, per accedere alla sezione dedicata alle impostazioni avanzate, la
dicitura “AutoPowerOff” apparirà sullo schermo.
Premere per selezionare il tempo di spegnimento automatico desidera-
to, è possibile scegliere tra le opzioni 5, 10 e 15 minuti.
Premere per confermare.
6 Setting
6.2 Advanced Setting
During power off state, holding down press
then press to entry advanced setting, the
“AutoPowerOff” will appear on the display screen.
Press to adjust, the auto power off time can be
set 5, 10 and 15 minutes
press to confirm.
Press again, the “Beep Volume” can be
change, press to adjust, the “Beep Volume”
can be set 0, 1 and 2.
press to confirm.
Press again, the “RestoreSettings” can be
change, press to adjust, press to confirm.
NOTE
If choice “YES”, all the setting parameters will be
covered by factory settings.
Press again, confirm the setting need to save
or not, press to adjust, press to save and
power off.
Page 13 / 26
Premere di nuovo per poter cambiare il volume (“BeepVolume”).
Premere per selezionare quello desiderato, è possibile scegliere tra
l’opzione 0, 1 e 2.
Premere per confermare.
6 Setting
6.2 Advanced Setting
During power off state, holding down press
then press to entry advanced setting, the
“AutoPowerOff” will appear on the display screen.
Press to adjust, the auto power off time can be
set 5, 10 and 15 minutes
press to confirm.
Press again, the “Beep Volume” can be
change, press to adjust, the “Beep Volume”
can be set 0, 1 and 2.
press to confirm.
Press again, the “RestoreSettings” can be
change, press to adjust, press to confirm.
NOTE
If choice “YES”, all the setting parameters will be
covered by factory settings.
Press again, confirm the setting need to save
or not, press to adjust, press to save and
power off.
Page 13 / 26
Premere di nuovo per poter settare lo strumento con le impostazioni di
fabbricazione “RestoreSetting”.
Premere per selezionareYES o NO. Premere per confermare.
Nota: se viene selezionato “YES”, verranno reimpostati i parametri di
fabbricazione.
6 Setting
6.2 Advanced Setting
During power off state, holding down press
then press to entry advanced setting, the
“AutoPowerOff” will appear on the display screen.
Press to adjust, the auto power off time can be
set 5, 10 and 15 minutes
press to confirm.
Press again, the “Beep Volume” can be
change, press to adjust, the “Beep Volume”
can be set 0, 1 and 2.
press to confirm.
Press again, the “RestoreSettings” can be
change, press to adjust, press to confirm.
NOTE
If choice “YES”, all the setting parameters will be
covered by factory settings.
Press again, confirm the setting need to save
or not, press to adjust, press to save and
power off.
Page 13 / 26
Premere di nuovo per poter confermare se le impostazioni devono
essere salvate oppure no, premere per selezionareYES o NO.
Premere per confermare.
