SAFE USAGE OF THE PROJECTOR
When unpacking and before disposing of the carton check there is no
be any damage caused by transportation, consult your dealer and do not use the apparatus
The projector is for indoor use only, IP20 Use only in dry locations Keep this device away from rai
humidity and dust Do not allow contact with water or any other liquids
The projector is not designed or intended to be mounted directly on to inflammable surfaces
The projector is only intended for installation, operat
The projector must be installed in a location with adequate ventilation, at least 50cm from adjacent wall surfaces Be sure t
ventilation slots are blocked
Do not project the beam onto inflammable
Avoid direct exposure to the light from the lamp The light is harmful to the eye
Do not attempt to dismantle and/or modify the projector in any way
Electrical connection must only be carried out by qualified
Before installation, ensure that the voltage and frequency of power supply match the power requirements of the projector
It is essential that each projector is correctly earthed and that electrical installation conforms to all relevant standa
Do not connect this device to any other types of dimmer apparatus
Make sure that the power-
cord is never crimped or damaged by sharp edges Never let the
Keep the lamp clean Do not touch the lamp glass with bare hand
The projector should always be installed with a secondary safety fixing A safety cord is supplied for this; it should be att
installing the projector” section
Shields and lens shall be changed if they have become visibly damaged to such an extent that their effectiveness is impaired,
example by cracks or deep scratches
Exterior surface temperatures of the luminaire
There is no user serviceable parts inside the projector, do not open the housing and never operate the projector with the cov
If you have any questions or suggestions, don’t hesitate to consult your dealer or manufacturer
Always disconnection from Power, when the device not in
The minimum distance between the unit and the illuminated surface must be more than 10
SAFE USAGE OF THE PROJECTOR
When unpacking and before disposing of the carton check there is no
transportation damage before using the projector Should there
be any damage caused by transportation, consult your dealer and do not use the apparatus
The projector is for indoor use only, IP20 Use only in dry locations Keep this device away from rai
n and moisture, excessive heat,
humidity and dust Do not allow contact with water or any other liquids
The projector is not designed or intended to be mounted directly on to inflammable surfaces
The projector is only intended for installation, operat
ion and maintenance by qualified personnel
The projector must be installed in a location with adequate ventilation, at least 50cm from adjacent wall surfaces Be sure t
surfaces, minimum distance is 10m
Avoid direct exposure to the light from the lamp The light is harmful to the eye
Do not attempt to dismantle and/or modify the projector in any way
Electrical connection must only be carried out by qualified
Before installation, ensure that the voltage and frequency of power supply match the power requirements of the projector
It is essential that each projector is correctly earthed and that electrical installation conforms to all relevant standa
Do not connect this device to any other types of dimmer apparatus
cord is never crimped or damaged by sharp edges Never let the
cord come into contact with other cables
pull out the plug by tugging the power-cord
Keep the lamp clean Do not touch the lamp glass with bare hand
The projector should always be installed with a secondary safety fixing A safety cord is supplied for this; it should be att
installing the projector” section
Shields and lens shall be changed if they have become visibly damaged to such an extent that their effectiveness is impaired,
Exterior surface temperatures of the luminaire
after 30 minutes operation is 45℃
, when steady state is achieved
There is no user serviceable parts inside the projector, do not open the housing and never operate the projector with the cov
If you have any questions or suggestions, don’t hesitate to consult your dealer or manufacturer
Always disconnection from Power, when the device not in
use or before cleaning or any maintenance
The minimum distance between the unit and the illuminated surface must be more than 10
transportation damage before using the projector Should there
n and moisture, excessive heat,
The projector must be installed in a location with adequate ventilation, at least 50cm from adjacent wall surfaces Be sure t
Before installation, ensure that the voltage and frequency of power supply match the power requirements of the projector
It is essential that each projector is correctly earthed and that electrical installation conforms to all relevant standa
cord come into contact with other cables
The projector should always be installed with a secondary safety fixing A safety cord is supplied for this; it should be att
Shields and lens shall be changed if they have become visibly damaged to such an extent that their effectiveness is impaired,
, when steady state is achieved
There is no user serviceable parts inside the projector, do not open the housing and never operate the projector with the cov
use or before cleaning or any maintenance
The minimum distance between the unit and the illuminated surface must be more than 10
