Powerwerx KG-UV3X PRO Manuel utilisateur

This Wouxun radio is warranted against failure due to defects in workmanship or

materials for 12 months from the date of purchase from Powerwerx or an authorized

Powerwerx dealer. The included radio battery and battery charger are warranted against

failure due to defects in workmanship or materials for 6 months from the date of purchase

from Powerwerx or an authorized Powerwerx dealer. If purchased from an authorized

Powerwerx dealer the item must be returned with a copy of the original sales receipt

or proof of purchase. Warranty does not include other accessories, antennas or knobs.

Warranty does not cover damage caused by abuse, accident, misuse, improper or

abnormal usage, failure to follow instructions, improper installation, alteration, moisture,

water, lightning, or other incidence of excessive voltage or current. If failure occurs within

this period, return the radio to Powerwerx at your shipping expense with a full explanation,

return address and necessary proof of purchase. The device or accessory will be repaired

or replaced, at our option, without charge, and returned to you at our shipping expense.

Repaired or replaced items are warranted for the remainder of the original warranty

period. Powerwerx shall have no liability or responsibility to customer or any other person

or entity with respect to any liability, loss, or damage.

Revised 12-19-12

Powerwerx, Inc.

263 N Berry St

Brea, CA 92821

Phone: 714-674-0073

Fax: 714-674-4949

www.powerwerx.com

Powerwerx Limited Warranty Policy

KG-UV3X PRO

Dual-band Land Mobile Radio

User Manual

Optional Accessories

KG-UV3X PRO Manual (Continued)

A wide variety of optional accessories are available for your KG-UV3X Pro.

Visit our website to learn more: www.powerwerx.com/wouxun-radios

Trouble Shooting

PROBLEM SOLUTION

Radio will not turn ON Recharge the battery in the desk charger

Radio will not Transmit Battery is low, recharge battery

Radio will not Transmit Channel TX is not enabled, reprogram

When Scanning, RX stops Take the channel out of scan list

on same channel and start scanning again (MENU 33)

Battery Life short Stop using Channel Scan feature

Battery Life short Turn Battery Saver ON (MENU 3)

Battery Life short Replace battery with new one

Receive Static on Radio Move radio away from computers or

 oresenttypelightscausinginterference

Wouxun KG-UV3X PRO

Professional Dual-Band Radio

Instruction Sheet

SUPPLIED IN THE BOX:

• Dual-band (VHF/UHF) Land Mobile Transceiver

• Extended life Li-ion battery pack (1700 mAh)

• Dual-band VHF/UHF Medium Length “X” Antenna

• Belt Clip

• Desktop Rapid Charger (charges in 1~3.5 hours)

• Handstrap

INSTALLING THE BATTERY AND ANTENNA

First, match the guides on the bottom of the battery pack with the back side

bottomoftheradio.Pressonthebattery(bottomrst)itwilllatchasyoupress

downward. (Press down on each side of the battery to release). Screw in the

supplied antenna into the top of the radio.

TURNING RADIO ON / OFF

Turn the top knob clockwise to turn radio ON. During power-up, radio will display

current battery voltage for 2 seconds then will display a dealer pre-programmed

message for 1 second then display current channel display. Turn this same top

mounted volume knob counter-clockwise to turn the radio OFF.

SPEAKER VOLUME ADJUSTMENT

Turn the top volume knob to adjust the radio volume higher or lower for desired

audio output.

CHANNEL SELECTION

Turn the top mounted channel selector to the desired channel. Built-in voice will

announce the channel number as you rotate this knob (if programmed).

PTT - PUSH TO TALK BUTTON

Press this key to transmit and release to listen.

FLASHLIGHT

Momentary press the bottom side monitor key (short press) to turn ON/OFF

Flashlight feature.

Getting Started

Congratulations on purchasing the model KG-UV3X PRO Dual-band radio

which is ideal for Fire, Police, EMS, Ski Patrol, Schools and the Hospitality

industries. This two-way radio offers many features that can be dealer

programmed depending on your requirements.

KG-UV3X PRO HANDHELD FEATURES:

• FCC 2013 Narrowband Compliant w/ 2.5 KHz Channel step

• Frequency Range: 136-174 RX/TX & 375-512 RX, 406-512 MHz TX

• 125 Channels (pre-programmed w/ 14 UHF & 2 VHF Channels)

• Single or Dual Alpha-Numeric Display & Voice Announcement

• Power Output: VHF: 5W High / 1W Low UHF: 4W High / 1W Low

• 15 Hours of operation: (85% Standby / 10% RX / 5% TX on low power)

• Built in Flashlight

• VOX Operation

2 7

MENU SELECTIONS

The MENU feature can be enabled or disabled in the Windows PC software.

Press the “MENU” button to adjust radio features. To access MENU functions,

press the MENU button then turn to top channel knob and select the desired

function. Within 3 seconds, press the MENU button again and use the top knob

toadjustthatmenuitemthenpressMENUtoconrm.PresstheEX/Keybutton

to exit.

MENU SELECTIONS

• 1 STEP........ CHANNEL STEP (select 2.5, 5.0, 10.0, 12.5, 25.0 KHz)

• 2 SQL-LE.... SQUELCH LEVEL (select level of 1-9, recommended is

“6”)

• 3 SAVE........ RECEIVE BATTERY SAVER (ON or OFF. Default is

ON)

• 4 TX............ TX POWER LEVEL (HI or LOW selection by channel)

• 5 ROGER.... ROGER BEEP (select before or after TX. Default in

none)

• 6 TOT.......... TIME-OUT-TIMER (select 15 ~ 600 seconds. Default is

60)

• 7 VOX......... VOX SETTING (select 1-9. Default is OFF)

• 8 RX-WN..... RX BANDWIDTH (select Narr or Wide)

• 9 VOICE...... VOICE ANNOUNCEMENT (Default is OFF)

• 10 TOA.......... TX TIME OUT WARNING (select 0-9. default is 5)

• 11 BEEP........ KEYPAD BEEP (select ON/OFF. Deafult is ON)

• 12 TX-WN..... TX BANDWIDTH (select Narr or Wide)

• 13 BCL.......... BUSY CHANNEL LOCK-OUT (Default is OFF)

• 14 AUTOLK... AUTO LOCK KEYPAD (ON/OFF. Default is OFF)

• 15 R-CTC...... RECEIVE CTCSS TONE (Default is OFF)

• 16 T-CTC....... TX CTCSS TONE (Default is OFF)

• 17 R-DCS...... RECEIVE DIGITAL CODED SQUELCH (Default is OFF)

• 18 T-DCS...... TX DIGITAL CODED SQUELCH (Default is OFF)

• 19 SC-RE...... SCAN MODE (Default is “Carrier Mode”)

• 20 PF-1......... SIDE KEY PROGRAMMING (Default is OFF)

• 21 PF-2......... FRONT MOUNTED BUTTON PROGRAMMING

(Default is RPT)

• 22 CH-MDF... DISPLAY MODE (Select Alpha, Channel or Freq display)

• 23 ABR.......... AUTO BACKLIGHTING (Select ON/OFF)

• 24 OFFSET... TX REPEATER OFFSET (Default is 0.600 & 5.000)

• 25 SFT-D....... REPEATER OFFSET DIRECTION (select +/-,

Deafult is OFF)

• 26 SECOND.. STOPWATCH (Default is OFF)

• 27 CHNAME.. CHANNEL ALPHA NAME

• 28 MEM-CH... MEMORY CHANNELS AVAILABLE

• 29 DEL-CH.... CHANNEL DELETE

• 30 RESET...... RESET RADIO (select VFO or ALL)

• 31 SOS-CH... SOS TX ON (select Channel A or B)

• 32 SCN CD.... TONE SCAN (select CTCSS or DCS. Default is CTCSS)

• 33 SCN ADD. MEMORY CHANNEL SCAN ADD / DELETE

• 34 LK-EN....... KEYPAD CH LOCK (ALL or PART)

• 35 PTT-ID...... PTT ID (Default is OFF)

KG-UV3X PRO Manual (Continued)

MONITOR KEY

Press and hold the monitor key for 2 seconds to turn ON or OFF the radio

squelch to listen without the tone squelch function.

BATTERY LEVEL (CAPACITY) DISPLAY

Turn the radio OFF. Wait 1 second, then turn radio back ON.

• Battery Voltage 8.0 ~ 8.4........ Battery is full (80-100%)

• Battery Voltage 7.7 ~ 7.9........ Battery is medium (60-80%)

• Battery Voltage 7.5 ~ 7.6........ Battery is low (40-60%)

• Battery Voltage 7.4 or less...... Battery needs recharging (0-40%)

BATTERY CHARGER OPERATION

Connect to AC power cord into the back of the charging base. Plug in the AC

cord into a standard wall outlet. Place the radio or battery into the charger cup.

Please refer to the battery charger status lights below.

Flashing Red Light.......................... Deep Battery Charging (3 1/2 hours)

Solid Red Light............................... Regular Battery Charging (1/2 to 3 hours)

Green Light..................................... Battery Fully Charged - Ready to use

SINGLE / DUAL DISPLAY

Press the S/D key to select single or dual d isplay. In most cases it is

recommended that you use a single display mode for simple operation.

CHANNEL DISPLAY SELECTION

Press the A/B key to select either top or bottom display. An arrow on the left

side of the LCD display will show which display is active.

KEYPAD AND CHANNEL KNOB LOCK

Front keypad and top channel knob can be locked. Press and hold for the front

mounted “Key” for 3 seconds. Depending how your radio is pre-programmed

with the computer software or MENU feature 34, there are 3 options available:

• Front Keypad locked but channel knob is still functional

• Front Keypad and top channel knob are locked

• Front Keypad and top channel knob are functional

SCANNING CHANNELS

Press the side mounted center Key for 2 for 1 second to start the memory

channel scanning feature. Momentary press the PTT button to stop the channel

scan feature. Scan feature must be turned on via the PC software or MENU 20

prior to use.

NOTE: Battery life is greatly reduced when in the “Scanning” mode.

SQUELCH SETTING

The Squelch adjustment is used to eliminate unwanted static and general noise.

Squelch setting may be adjusted “MENU 2” (or computer software) from (0 - 9).

The “0” setting is squelch OFF and the “9” setting it the tightest squelch. It is

recommendedthatyouusethedefaultsquelchsettingof“6”whenrstusing

the radio. NOTE: if you are listening on a VHF channel near a computer, you

may hear static on your radio. Try adjusting the squelch to a setting of “8” or “9”

or move radio away from the computer to eliminate this noise.

Getting Started (Continued)

Channel Selector Power/Volume Switch

Transmit Light

Receive Light

Microphone

Antenna

PTT Push to

Talk) Key

Monitor Key

(Long Press)

Flashlight

(Short Press)

Speaker

Radio Diagram

Accessory

Jack

Aux Function

This VHF/UHF Dual-band handheld is FCC 2013 Narrow band compliant.

Please note the following default TX modulation settings for the

KG-UV3X PRO.

VHF BAND

136.000-143.995 MHz..... Narrow Band (2.5 KHz) TX, Wide or Narrow RX by channel

144.000-148.000 MHz..... Amateur Band (5.0 KHz) or Narrow band (2.5 KHz) RX/TX

148.005-174.000 MHz..... Narrow Band (2.5 KHz) TX, Wide or Narrow RX by channel

UHF BAND

400.000-430.000 MHz..... Narrow Band (2.5 KHz) TX, Wide or Narrow RX by channel

430.005-450.000 MHz..... Amateur Band (5.0 KHz) or Narrow band (2.5 KHz) RX/TX

450.005-470.000 MHz..... Narrow Band (2.5 KHz) TX, Wide or Narrow RX by channel

470.005-512.000 MHz..... Land Mobile Band (5.0 KHz) or Narrow band (2.5 KHz) RX/TX

PRE-PROGRAMMED CHANNELS

Your radio is pre-programmed with (14) UHF & (2) VHF channels. Powerwerx/

Wouxun radios operate on business radio frequencies that are regulated by

the FCC. In order to transmit on these frequencies, you are required to have

a license issued by the FCC. Visit: http://wireless.fcc.gov/services/index.

htm?job=service_home&id=industrial_business

Your dealer can also re-program your radio’s channels with different frequencies

and features as needed (see below)

PRE-PROGRAMMED CHANNELS

Channel 1 464.550 MHz 67.0 Tone 1W Business Ch. CLS-1 (Narrow 2.5 KHz)

Channel 2 467.925 MHz 67.0 Tone 1W Business Ch. CLS-2 (Narrow 2.5 KHz)

Channel 3 467.850 MHz 67.0 Tone 1W Business Ch. CLS-3 (Narrow 2.5 KHz)

Channel 4 467.875 MHz 67.0 Tone 1W Business Ch. CLS-4 (Narrow 2.5 KHz)

Channel 5 469.5125 MHz 77.0 Tone 1W Business Ch. CLS-54 (Narrow 2.5 KHz)

Channel 6 466.3125 MHz 110.9 Tone 1W Business Ch. CLS-45 (Narrow 2.5 KHz)

Channel 7 466.3375 MHz 110.9 Tone 1W Business Ch. CLS-46 (Narrow 2.5 KHz)

Channel 8 466.3625 MHz 110.9 Tone 1W Business Ch. CLS-47 (Narrow 2.5 KHz)

Channel 9 467.7875 MHz 110.9 Tone 1W Business Ch. CLS-48 (Narrow 2.5 KHz

Channel 10 467.8375 MHz 110.9 Tone 4W Business Ch. CLS-49 (Narrow 2.5 KHz)

Channel 11 467.8625 MHz 110.9 Tone 4W Business Ch. CLS-50 (Narrow 2.5 KHz)

Channel 12 467.8875 MHz 110.9 Tone 4W Business Ch. CLS-51 (Narrow 2.5 KHz)

Channel 13 467.9125 MHz 110.9 Tone 4W Business Ch. CLS-52 (Narrow 2.5 KHz)

Channel 14 469.4875 MHz 110.9 Tone 4W Business Ch. CLS-53 (Narrow 2.5 KHz)

Channel 15 154.570 MHz 88.5 Tone 1W VHF Business Ch. (Narrow 2.5 KHz)

Channel 16 154.600 MHz 88.5 Tone 1W VHF Business Ch. (Narrow 2.5 KHz)

PC PROGRAMMING

This radio is shipped with the keypad locked per FCC Requirements.

PC Programing software and USB cable are required to unlock the keypad

and program this model radio. This software and PC programming cable kit

are available from Powerwerx or authorized dealers that sell this model radio.

Please order the following SKU to program this radio:

RPS-3X PRO-USB Windows Programming Software and Gray USB Cable

NOTE:

Windows software is compatable with Windows 8, Windows 7, Vista and XP

operating systems.

CAUTION:

Use of any third party software other than what is listed above may result in

damage to the radio which voids the warranty. No exceptions!

KG-UV3X PRO Manual (Continued)

Toggle Single/

Dual Recieve

Table des matières

Autres manuels Powerwerx Radio

Powerwerx

Powerwerx DB-750X Manuel utilisateur

Manuels Radio populaires d'autres marques

EisSound

EisSound KBSound iSelect Manuel utilisateur

Midland

Midland 1001LWX Manuel utilisateur

Konig

Konig HAV-SR41 Manuel utilisateur

Roberts

Roberts exprssion Manuel utilisateur

VDigi

VDigi DD3.0 Manuel utilisateur

Radio Shack

Radio Shack 21-1863 Manuel utilisateur

Roberts

Roberts Stream 207 Manuel utilisateur

Sony

Sony Walkman SRF-M97 Manuel utilisateur

Stanley

Stanley FatMax FMC770 Manuel utilisateur

auna

auna DAB-Radio 10026947 Manuel utilisateur

SOUNDMASTER

SOUNDMASTER UR190 Manuel utilisateur

HYT

HYT TC-320 Manuel utilisateur

auna multimedia

auna multimedia Yellowstone 10026851 Manuel utilisateur

B-Tech

B-Tech GMRS-V2 Manuel utilisateur

Weierwei

Weierwei VEV-V8 Manuel utilisateur

SOUNDMASTER

SOUNDMASTER DAB750 Manuel utilisateur

Telefunken

Telefunken TF-1505 Manuel utilisateur

Makita

Makita LXRM03 Manuel utilisateur