PowerWalker VFI 10000 CP 3/3 BI Manuel utilisateur

PowerWalker

VFI 10000 CP 3/3 BI

VFI 15000 CP 3/3 BI

VFI 20000 CP 3/3 BI

VFI 30000 CP 3/3 BI

VFI 10000 CPR 3/3

VFI 15000 CPR 3/3

VFI 20000 CPR 3/3

Manual

Uninterruptible Power Supply System

Version: 1.1

Please comply with all warnings and operating

instructions in this manual strictly. Save this

manual properly and read carefully the following

instructions before installing the unit. Do not

operate this unit before reading through all

safety information and operating instructions

carefully.

Table of Contents

1. SAFETY AND EMC INSTRUCTIONS ................................................................................................. 1

1-1. TRANSPORTATION AND STORAGE...............................................................................................................1

1-2. PREPARATION.......................................................................................................................................1

1-3. INSTALLATION ......................................................................................................................................1

1-4. CONNECTION WARNINGS ...............................................................................................................2

1-5. OPERATION .........................................................................................................................................3

1-6. STANDARDS .........................................................................................................................................3

2. INSTALLATION AND OPERATION .................................................................................................. 4

2-1. UNPACKING AND INSPECTION ...................................................................................................................4

2-2. REAR PANEL VIEW.................................................................................................................................5

2-3. SINGLE UPS INSTALLATION .....................................................................................................................6

2-4. UPS INSTALLATION FOR PARALLEL SYSTEM ..................................................................................................8

2-5. SOFTWARE INSTALLATION .....................................................................................................................10

3. OPERATIONS................................................................................................................................ 11

3-1. BUTTON OPERATION ............................................................................................................................11

3-2. LED INDICATORS AND LCD PANEL ..........................................................................................................11

3-3. AUDIBLE ALARM..................................................................................................................................13

3-4. SINGLE UPS OPERATION ......................................................................................................................13

3-5. PARALLEL OPERATION ..........................................................................................................................16

3-6. ABBREVIATION MEANING IN LCD DISPLAY.................................................................................................17

3-7. LCD SETTING ....................................................................................................................................18

3-8. OPERATING MODE/STATUS DESCRIPTION .................................................................................................23

3-9. FAULT CODE ......................................................................................................................................29

3-10.WARNING INDICATOR .........................................................................................................................29

3-11.WARNING CODE ................................................................................................................................30

4. TROUBLE SHOOTING ................................................................................................................... 31

5. STORAGE AND MAINTENANCE..................................................................................................... 33

5-1. STORAGE ..........................................................................................................................................33

5-2. MAINTENANCE....................................................................................................................................33

6. SPECIFICATIONS ......................................................................................................................... 34

1. Safety and EMC instructions

Please read carefully the following user manual and the safety instructions before installing the unit or using

the unit!

1-1. Transportation and Storage

Please transport the UPS system only in the original package to protect against shock and

impact.

The UPS must be stored in the room where it is ventilated and dry.

1-2. Preparation

Condensation may occur if the UPS system is moved directly from cold to warm environment.

The UPS system must be absolutely dry before being installed. Please allow at least two hours for the

UPS system to acclimate the environment.

Do not install the UPS system near water or in moist environments.

Do not install the UPS system where it would be exposed to direct sunlight or nearby heater.

Do not block ventilation holes in the UPS housing.

1-3. Installation

Do not connect appliances or devices which would overload the UPS (e.g. big motor-type

equipment)) to the UPS output sockets or terminal.

Place cables in such a way that no one can step on or trip over them.

Do not block air vents in the housing of UPS. The UPS must be installed in a location with good

ventilation. Ensure enough space on each side for ventilation.

UPS has provided earthed terminal, in the final installed system configuration, equipotential

earth bonding to the external UPS battery cabinets.

The UPS can be installed only by qualified maintenance personnel.

An appropriate disconnect device as short-circuit backup protection should be provided in the

building wiring installation.

An integral single emergency switching device which prevents further supply to the load by the

UPS in any mode of operation should be provided in the building wiring installation.

Connect the earth before connecting to the building wiring terminal.

Installation and Wiring must be performed in accordance with the local electrical laws and

regulations.

1-4. Connection Warnings

There is no standard backfeed protection inside, please isolate the UPS before working according to

this circuit. The isolation device must be able to carry the UPS input current.

•This UPS should be connected with TN earthing system

•The power supply for this unit must be three-phase rated in accordance with the equipment nameplate.

It also must be suitably grounded

•Use of this equipment in life support applications where failure of this equipment can reasonably be

expected to cause the failure of the life support equipment or to significantly affect its safety or

effectiveness is not recommended. Do not use this equipment in the presence of a flammable anesthetic

mixture with air, oxygen or nitrous oxide.

•Connect your UPS power module’s grounding terminal to a grounding electrode conductor.

•The UPS is connected to a DC energy source (battery). The output terminals may be live when the UPS

is not connected to an AC supply.

Before working on this circuit

-Isolate Uninterruptible Power System (UPS)

-Then check for Hazardous Voltage between all

terminals including the protective earth.

Risk of Voltage Backfeed

1-5. Operation

Do not disconnect the earth conductor cable on the UPS or the building wiring terminals in any

time since this would cancel the protective earth of the UPS system and of all connected loads.

The UPS system features its own, internal current source (batteries). The UPS output sockets or

output terminal blocks may be electrically live even if the UPS system is not connected to the building

wiring outlet.

In order to fully disconnect the UPS system, first press the “OFF” button and then disconnect the

mains.

Ensure that no liquid or other foreign objects can enter into the UPS system.

The UPS can be operated by any individuals with no previous experience.

1-6. Standards

* Safety

IEC/EN 62040-1

* EMI

Conducted Emission...............................:IEC/EN 62040-2

Category C3

Radiated Emission..................................:IEC/EN 62040-2

Category C3

*EMS

ESD.........................................................:IEC/EN 61000-4-2

Level 4

RS........................................................ ...:IEC/EN 61000-4-3

Level 3

EFT......................................................... :IEC/EN 61000-4-4

Level 4

SURGE................................................... :IEC/EN 61000-4-5

Level 4

CS........................................................... :IEC/EN 61000-4-6

Level 3

Power-frequency Magnetic field.............. :IEC/EN 61000-4-8

Level 4

Low Frequency Signals............................:IEC/EN 61000-2-2

Warning: This is a product for commercial and industrial application in the

second environment-installation restrictions or additional measures may be

needed to prevent disturbances.

2. Installation and Operation

There are two different types of online UPS: standard and long-run models. Please refer to the following

model table.

Model

Type

Model

Type

10000 CP(R)

Standard

model

Long-run

model

15000 CP(R)

20000 CP(R)

30000 CP(R)

We also offer optional parallel function for these two types by request. The UPS with parallel function is

called as “Parallel model”. We have described detailed installation and operation of Parallel Model in the

following chapter.

2-1. Unpacking and Inspection

Unpack the package and check the package contents. The shipping package contains:

● One UPS

●One user manual

● One monitoring software CD

●One RS-232 cable (option)

●One USB cable

●One parallel cable (only available for parallel model)

●One share current cable (only available for parallel model)

NOTE: Before installation, please inspect the unit. Be sure that nothing inside the package is damaged

during transportation. Do not turn on the unit and notify the carrier and dealer immediately if there is any

damage or lacking of some parts. Please keep the original package in a safe place for future use.

2-2. Rear Panel View

Diagram 1: 10000-20000 CP Diagram 2: 30000 CPS Rear Panel Diagram 3: 30000CP Rear Panel

Rear Panel

Diagram 4: Rack Rear Panel Diagram 5: Rack

Input/Output Terminal

Diagram 6: 10000-20000 CP Diagram 7: 30000CP

Input/Output Terminal Input/Output Terminal

1. RS-232 communication port

2. USB communication port

3. Emergency power off function connector (EPO connector)

4. Share current port (only available for parallel model)

5. Parallel port (only available for parallel model)

6. Intelligent slot

7. Power stage fan

8. External battery connector (Only available for long-run model)

9. Bypass Input Circuit Breaker(Only available for dual input unit)

10. Input/Output terminal (Refer to Diagram 5, 6 and 7)

11. Line Input circuit breaker

12. Maintenance bypass switch

13. Output Grounding terminal

14. Output terminal: connect to mission-critical loads

15. Line input terminal

16. Bypass input terminal(Only available for dual input)

17. Input Grounding terminal

18. External maintenance bypass switch port

2-3. Single UPS Installation

Installation and wiring must be performed in accordance with the local electric laws/regulations and execute

the following instructions by professional personnel.

1) Make sure the mains wire and breakers in the building are enough for the rated capacity of UPS to

avoid the hazards of electric shock or fire.

NOTE: Do not use the wall receptacle as the input power source for the UPS, as its rated current is less than

the UPS’s maximum input current. Otherwise the receptacle may be burned and destroyed.

2) Switch off the mains switch in the building before installation.

3) Turn off all the connected devices before connecting to the UPS.

4) Prepare wires based on the following table:

Model

Wiring spec (AWG)

Input(Ph)

Output(Ph)

Neutral

Battery

Ground

10000

15000

20000

30000

NOTE 1: The cable for 10kVA should be able to withstand over 40A current. It is recommended to use

AWG 10 or thicker wire for Phase and AWG 8 or thicker wire for Neutral for safety and efficiency.

NOTE 2: The cable for 15kVA should be able to withstand over 63A current. It is recommended to use

AWG 8 or thicker wire for Phase and AWG 6 or thicker wire for Neutral for safety and efficiency.

NOTE 3: The cable for 20kVA should be able to withstand over 63A current. It is recommended to use

AWG 8 or thicker wire for Phase and AWG 6 or thicker wire for Neutral for safety and efficiency.

NOTE 4: The cable for 30kVA should be able to withstand over 63A current. It is recommended to use

AWG 8 or thicker wire for Phase and AWG 4 or thicker wire for Neutral for safety and efficiency.

NOTE 5: The selections for color of wires should be followed by the local electrical laws and

regulations.

5) Remove the terminal block cover on the rear panel of UPS. Then connect the wires according to the

following terminal block diagrams: (Connect the earth wire first when making wire connection. Disconnect

the earth wire last when making wire disconnection!)

Terminal Block wiring diagram of 10000-20000 CP

Terminal Block wiring diagram of 30000CP

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels PowerWalker Alimentation

PowerWalker

PowerWalker VFI 30K CPG 3/3 Manuel utilisateur

PowerWalker

PowerWalker VFI 60K CPG 3/3 BX Manuel utilisateur

PowerWalker

PowerWalker VI ERT HID Series Manuel utilisateur

Manuels Alimentation populaires d'autres marques

Monacor

Monacor PS-12CCD Manuel utilisateur

VOLTIMA

VOLTIMA MagicBox 15 Manuel utilisateur

Agilent Technologies

Agilent Technologies 6032A Manuel utilisateur

Miller

Miller Auto Deltaweld 452 Manuel utilisateur

BCP

BCP PUOUBK Feuille d'instructions

HC 2210 Manuel utilisateur

Puls

Puls CT5.241 Manuel utilisateur

OCZ

OCZ ZX1250W Manuel utilisateur

iseg

iseg ECH 238 Manuel utilisateur

Power

Power XXL A Series Manuel utilisateur

Agilent Technologies

Agilent Technologies 6631B Manuel utilisateur

Renogy

Renogy PHOENIX 300 Manuel utilisateur

HP 6200B Manuel de service

Epson

Epson Stylus Scan 2500 Manuel d'utilisation

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 Manuel utilisateur

Puls

Puls MiniLine ML50.100 Manuel utilisateur

Puls

Puls AS-Interface SLA4.100 Manuel utilisateur

Kenwood

Kenwood PS-60 Manuel utilisateur