Powerline A3G Manuel utilisateur

INSTRUCTION MANUAL

A3G Green Rotary Laser

SPECIAL EDITION

Please read this instruction manual before operating this product.

Please store this instruction manual in the carry case for future reference.

CAUTION: Class 3 Laser Product

Do not stare directly into the laser beam from apertures.

Do not disassemble the instrument or attempt to perform any internal servicing

as this will void your warranty. No user serviceable parts included.

Only approved and authorised service technicians can carry out warranty repairs.

SAFETY

Powerline A3G

Please ensure the following items are included with your laser.

If anything is missing please contact your retailer.

ITEM CHECKLIST

90°

45°

10°

180°

Laser glasses Rechargeable

battery pack

Alkaline

battery pack

ChargerCarry case

Laser targetDetector and clampRemote control

INCHES CM

OFF

Wall mount

Rotating laser port Protective lighthouse

PRODUCT OVERVIEW

Control panel

90°

45°

10°

180°

CONTROL PANEL

Power

Tilt alarm indicator

Power indicator

Speed control

Counter clockwise rotation

Y-axis up / down

X-axis up / downX-axis up / down

Tilt alarm

Clockwise rotation

Manual / automatic mode

Scanning mode

Manual / automatic mode indicator

OFF

DETECTOR CONTROL PANEL

Sound on / off

Coarse / fine mode

LCD display screen Laser sensor

Bubble vial

Speaker

Power

90°

45°

10°

180°

REMOTE CONTROL PANEL

Manual / automatic mode

Button indicator

Counter clockwise rotation

Scanning mode

Clockwise rotation

Speed control

Y-axis up / down

X-axis up / down

Y-axis up / down

X-axis up / down

USING YOUR LASER

Power Supply

‣The Powerline A3G is supplied with a rechargeable Ni-MH battery pack that is

located in the base of the unit.

‣It is recommended that the battery pack be completely charged before use.

‣Charging time is approximately 5 hours.

‣Use of the unit over time and changes in temperature may cause increases

or decreases in charging and operation time.

‣The power indicator light will flash when the battery is low. The unit should

be re-charged as soon as possible.

‣To charge the unit insert the charger into the port on the battery pack.

Progress will be shown by the power indicator display on the charger as below:

Red (flashing) = Charger and battery are not connected.

Red (constant) = Battery is charging.

Green (constant) = Battery is charged.

Horizontal Set Up

‣Select a place as close as practical to the work site.

Ensure the location is clear of traffic.

‣Attach the laser to a tripod and place on a level surface.

Ensure the unit is secured correctly and tightened in position.

Vertical Set Up

‣Select a place as close as practical to the work site.

Ensure the location is clear of traffic.

‣Place the laser onto a level surface with the control panel facing upwards.

Operation

‣To turn the unit on press the power button. Self levelling will commence

and the laser will begin to rotate.

‣If the unit is outside the self levelling range the unit will not level causing

the laser beam to flash continuously.

Speed control

‣Press the speed control button to cycle through various rotational speeds.

‣The speed control indicator will flash slowly when speed is slow and fast

when speed is increasing.

Scanning mode

‣To focus the laser beam between two points press the scanning mode

button. Pressing the button multiple times will adjust the angle of the beam.

‣To cancel scan mode press the scanning mode button several times

to cycle through to full rotation.

Rotation

‣Whilst the unit is in scanning mode press the clockwise or counter

clockwise button to change the rotation of the laser head.

Table des matières

Autres manuels Powerline Niveau à croix laser

Powerline

Powerline A2 SPECIAL EDITION Manuel utilisateur

Powerline

Powerline X2G Manuel utilisateur

Manuels Niveau à croix laser populaires d'autres marques

Lasertec

Lasertec HV1R Manuel utilisateur