Postium PRM-503A Manuel utilisateur

LCDRacksMonitor

PRM-503A

MULTI-CHANNEL LCD MONITOR

User

Manual

Contents

PRM-503A

Warnings .......................................................................................................... 3

Features ............................................................................................................ 4

Name & Function of Each Part ......................................................................... 5

OSD Menu Organization & Adjustment ........................................................... 7

Other Functions .............................................................................................. 15

Special Functions ........................................................................................... 25

System Default Value...................................................................................... 26

Product Specification ..................................................................................... 27

PRM-503A MULTI-CHANNEL LCD MONITOR

Warning

· Always use set voltage.

- DC 12V

· If liquid is spilled on or impacts this product, please disconnect the product immediately

and seek professional help before continued use.

· Keep unit disconnected during extended periods of disuse.

Keep unit in a well-ventilated place to prevent overheating.

Do not install the product near any heat-generating equipment.

Also, keep the product out of direct sunlight or dusty areas.

Only clean the product with a noncommercial, mild and neutral detergent.

When transporting the product, make use of its original packaging for safer carriage.

FCC (Federal Communications Commission)

This equipment has been tested and found to comply with the limits for class A digital device, pursuant to

part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interface when the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in

accordance with the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential to correct the interference at his own expense

Warning!! : Change or modifications not expressly approved by the manufacturer responsible for

compliance void the user’s authority to operate the equipment.

Disposal of Old Electrical & Electronic Equipment

(Applicable in the European Union and other European countries

with separate collection systems)

This symbol on the product or on its packing indicates that this product shall not be treated as household

waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and

electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential

negative consequence for the environment and human health, which could otherwise be caused by

inappropriate waste handling of this product. The recycling of materials will help to conserve natural

resources.

Features

Multi-Format PRM-503A Series unit has the following features:

· Compatible with varied SDI Signals

The product is compatible with varied SDI signal

-480i,576i,720p,1035i,1080i,1080p,1080psf, 2K

· Compatible with varied Composite Signals

- NTSC, PAL, SECAM

· Waveform/Vector Scope/Audio Level Meter

Waveform & Vector Scope available for SDI Signals

Embedded Audio Level Meter

· BLUE ONLY/MONO

· H/V delay

· Wide Variety of Markers & Safety Areas

Center Marker, Safety Area Marker, Aspect Marker, Display Size(Scan)

· Pixel To Pixel

Provides both full screen and unscaled native image.

· Wide Screen/LED Backlight

· 24Bit RGB Interface Panel

· DC Compatible

The product is powered by normal 12V source.

· Remote control function

Simple remote controllability with single cable connection, no additional modules required

· Additional Features

Active Loop Through/SDI, 600:1 contrast ratio, 300 cd/m2 brightness, OSD user interface,

Rack Mountable

PRM-503A MULTI-CHANNEL LCD MONITOR

Name & Function of Each Part

· [INPUT] button

Used to select SDI A / SDI B / COMPOSITE Input (Rotation)

· [MENU] button

Used to activate the OSD menu.

· [UP] button

Used to navigate menu during OSD menu activation. It may also be used to toggle

clockwise through 1:1 quadrants in native scan mode

· [DOWN] button

Used to navigate menu during OSD menu activation. It may also be used to toggle

counterclockwise through 1:1 quadrants in native scan mode

· [ENTER] button

Used to confirm a chosen value (or mode) within the OSD menu.

This can be used to control the position of Waveform in small size.

· [POWER] button

Power On/Off button.

If the signal is normal, LED lights in Green. If the signal is unsupported or disconnected,

LED lights in Yellow.

· TALLY

LED indicating monitor’s current status using optional Remote.

ENTER DOWN UP MENU INPUT

<FRONT>

TALLY

POWER

LED

Name & Function of Each Part

· REMOTE (RJ-45)

Connection for remote control of monitor.

· SDI A-IN (BNC)

SDI A signal input terminal

· SDI B-IN (BNC)

SDI B signal input terminal

· SDI-OUT (BNC)

SDI signal output terminal

· COMPISITE INPUT (BNC)

COMPOSITE signal input terminal

· COMPOSITE OUTPUT (BNC)

COMPOSITE signal output terminal

· FACTORY PGM (15 pins)

Input connector for FACTORY PGM allowing for firmware updates.

· DC IN (XLR, 4 pins)

Used to supply DC power; 12V

<REAR>

SDI OUTPUT

SDI B INPUT

SDI A INPUT

COMPOSITE OUTPUT

COMPOSITE INPUT

DC IN

REMOTE

FACTORY PGM

DC IN soket

1: GND

4: +12V

PRM-503A MULTI-CHANNEL LCD MONITOR

OSD Menu Organization & Adjustment

[1] MAIN - Picture

· Brightness

This Item controls the degree of brightness.

· Contrast

This item controls the contrast ratio.

· Chroma

This item controls saturation.

· Aperture

This item controls the picture sharpness.

· Phase

This item controls Phase value (Hue).

#This function is only available in Composite Input.

· NTSC Setup

This item sets IRE value in NTSC mode between 0 IRE and 7.5 IRE.

#This function is only available in Composite NTSC Input.

OSD Menu Organization & Adjustment

[2] MAIN - Color

· Color Temp

This item controls Color Temperature with presets of 3200K, 5600K, 6500K, 9300K and User1,

User2, User3 mode.

· User

On User Mode, the user may select and control R, G, & B GAIN, BIAS values by using the

[UP]/[DOWN]/[ENTER] buttons.

· Color Copy

In User Mode, user can copy the preset of 3200K, 5600K, 6500K or 9300K to make the custom

adjustment by using the Up/Down/Enter buttons.

[3] MAIN - Marker

· Marker

Used to show MARKER on the screen. The type of marker at work may be selected on the other

menu.

#This feature disables when the H/V Delay or Pixel to Pixel mode is activated.

PRM-503A MULTI-CHANNEL LCD MONITOR

OSD Menu Organization & Adjustment

· Line Marker

This selects the marker type when the Line Marker is displayed on the screen.

Compatible Line MARKER types are as follows:

· Center Marker

This item displays the Center Marker on the screen.

· Safety Area

This item controls the size of the Safety Area between 80%, 85%, 88%, 90%, 93% and 100%.

· Marker Mat

This item darkens the area outside of Line Marker setting area. The degree of the matte is

between OFF(0) and (7).

The higher the number the darker Line Marker the matte becomes.

· Marker Color

This item controls Marker color. Selectable colors are white, gray, black, red, green and blue.

# Line Marker, Center Marker and Safety Area functions are operates only after activating

the MARKER function by setting to ‘On’ the Marker menu.

[4] MAIN - Remote

REMOTE (RJ-45)

1: Pin1

2: Pin2

3: Pin3

4: Pin4

5: Pin5

6: Pin6

7: Pin7

8: GND

1 8

MODE Line Marker CLASS

SD 16:9

16:9, 4:3, 4:3 ON AIR, 15:9, 14:9,

13:9, 1.85:1, 2.35:1, 1.85:1 & 4:3

SD 4:3

16:9

OSD Menu Organization & Adjustment

· Pin1 ~ Pin6

The user may connect RJ-45 jack to the remote terminal on the rear of the unit and designate a

function for each pin.

The selectable functions are as follows:

· Pin7

PIN7 is for POWER ON/OFF use only.

[5] MAIN - System [page1]

· System Default

User can use the System Default menu to initialize the values of the monitor.

· WaveForm

This item controls the Waveform or Vector Scope.

ANALOG CHANNEL, DIGITAL A CHANNEL, DIGITAL B CHANNEL

TALLY RED, TALLY GREEN

BLUE ONLY

UNDERSCAN

ASPECT

HVDELAY

16:9 MARKER, 15:9 MARKER, 14:9 MARKER,

13:9 MARKER, 4:3 MARKER, 4:3 ON AIR MARKER,

1.85:1 MARKER, 2.35:1 MARKER, 1.85:1 & 4:3 MARKER

CENTER MARKER

SAFETY AREA 80%, SAFETY AREA 85%, SAFETY AREA 88%,

SAFETY AREA 90%, SAFETY AREA 93%, SAFETY AREA 100%

Table des matières

Autres manuels Postium Moniteur

Postium

Postium PRM-483A Manuel utilisateur

Postium

Postium OBM-U090 Manuel utilisateur

Postium

Postium PRM-902Q Manuel utilisateur

Postium

Postium OBM-H120 Manuel utilisateur

Postium

Postium OBM-U240 Manuel utilisateur

Postium

Postium PRM-207Q Manuel utilisateur

Postium

Postium OBM-U178K Manuel utilisateur

Postium

Postium OBM-N170G Guide de démarrage rapide

Postium

Postium OBM-U Series Guide de démarrage rapide

Postium

Postium OBM-N Series Manuel utilisateur

Postium

Postium PRM-702A Manuel utilisateur

Postium

Postium OBM-N180 Guide de démarrage rapide

Postium

Postium PRM-502LE Manuel utilisateur

Postium

Postium OBM-N070 Manuel utilisateur

Postium

Postium PRM-434A Manuel utilisateur

Postium

Postium PRM-902A Manuel utilisateur

Postium

Postium OBM N Series Manuel utilisateur

Postium

Postium OBM-8K Series Guide de démarrage rapide

Postium

Postium OBM-Q Series Guide de démarrage rapide

Postium

Postium PRM-902F Manuel utilisateur

Manuels Moniteur populaires d'autres marques

Linear Acoustic

Linear Acoustic LQ-1000 Manuel utilisateur

AOC

AOC I2579V Manuel utilisateur

Gateway

Gateway FPD1520 Manuel utilisateur

Furuno

Furuno Mu 120c Manuel utilisateur

Asus

Asus VB171D - 17" LCD Monitor Manuel utilisateur

Dell

Dell S2230MX Instructions d'utilisation

Philips

Philips 107C64 Manuel utilisateur

Dell

Dell S2409WFP Manuel utilisateur

EverFocus

EverFocus EN-7517E Manuel utilisateur

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Manuel utilisateur

Dell

Dell Precision 7680 Mode d’emploi

LG 50PM1M - - 50" Plasma Panel Manuel utilisateur

Bosch

Bosch DDU 9 Manuel utilisateur

Acer

Acer A231HL Manuel utilisateur

Philips

Philips 86BDL4152T Manuel utilisateur

NEC

NEC AccuSync LCD5V Manuel utilisateur

Emay

Emay SleepO2 Manuel utilisateur

IBM

IBM 6360 Instructions d'installation