POSline SC2100B Manuel du propriétaire
SC2100B
Start Configuration
Chap.1 System Information
Set All default
S/W Version
Chap.2 System Installation
2.1 Interface Selection
If you change the interface from others to USB the program
needs to restart plug the installation.
<Keyboard>
USB
RS-232
2.2.1 Keyboard Terminal Type
<PC/AT PS/2>
IBM PS/2 30-80
PS/2 25，30
IBM XT
IBM 5550
NEC 9801
End Configuration
2
Start Configuration
2.2.2 Language
<U.S.A>
Spanish
Germany
Italian
French
Japan
2.2.3 Keyboard Wedge function
Function Key Emulation
<OFF>
KB Emulation(For NB)
<OFF>
ALT Mode
<OFF>
ON
ON
ON
ON
Caps Lock
End Configuration
3
Start Configuration
<OFF>
Num Lock
<OFF>
ON
2.2.4 Inter-character Delay (Default：00)
Appendix A （00H — 64H）
2.2.5 Inter-message Delay(Default：00)
Appendix A（00H—0AH）
Delay time=set up data*100(ms)
2.2.6 Keyboard Speed(Default：
00)
Appendix A（00H—08H）
2.2.7 Message Terminator
None
Tab
CR + LF
<CR>
ESC
End Configuration
4
Start Configuration
2.3.1 RS-232 Parameters
BAUD Rate
1200
4800
19200
2400
<9600>
38400
Data bits
7
Stop Bit
<1>
<8>
2
End Configuration
5
Start Configuration
Parity
<None>
Even
Space
Odd
Mark
RS-232 Function Installation
Handshaking Protocol Delay
Inter-character Delay (Default：
00)
Appendix A（00H—64H）
Delay time=set up data*100(ms)
Handshaking Protocol Delay（De-
fault：00)
Appendix A（00H—0AH）
Delay time=set up
data*1(ms)
Inter-message Delay
（Default：00)
Appendix A（00H—0AH）
Handshaking Protocol
<None>
ACK/NAK
RTS/CTS
Xon/Xoff
2.4 Scan Mode
Time out set up
End Configuration
6
Start Configuration
1. Scan the barcode of “Continuous/Timeout OFF”
2. Scan 2 digits of the ASCII code of the Appendix A
3. Scan the “End” of the Appendix A
4. Scan the End Configuration to end the procedure
5. The settings unit is a second. Ex:0*40 stands for 1
minute
The Timeout Default is 0*B4 about 3 minutes
Trigger On/Off
Continuous/Trigger Off
Continuous/LED always On
Flash On
<Trigger On/Good read
off>
Testing
Continuous/Timeout Off
Continuous/No Trigger
2.5 Buzzer Set-up
You can pitch the buzzer tone and adjust the buzzer time.
Besides you can set the voice of boot and decoding..
Frequency（Default：0AH）
Appendix A(00-10H)
Power On Tone
Adjust Buzzer
Tone（Default：05H）
Appendix A(00-10H)
End Configuration
7
Start Configuration
ON
Good read Beep
<ON>
OFF
OFF
2.6 Character Installation
The preamble and postamble character: You can put 10 AS-
CII at most in front of the barcode data. When the installa-
tion is “0” that means you don’t need to add the first and
last character. Please find the format as below:
Preamble Character Barcode Postamble Character
The process for adding the first and last character to the bar-
code:
1. Scan the barcode of “Start Configuration” and “The
Preamble Character Installation”.
2. Check the ASCII table to get the ASCII code of the
first and last character.
3. Scan the barcode of ASCII in the Appendix.
4. Scan the “End Configuration”.
G1/G2 character Insertion: You can put 10 ASCII at most in
front of the barcode data. When the installation is “0” that
means you don’t need to add the first and last character.
1. Scan the barcode of the “Start Configuration” and “G1
Insert Character”.
2. Check the ASCII table to get the ASCII code of the
first and last character.
3. Scan the barcode of ASCII in the Appendix.
4. Scan the “End Configuration”.
5. Repeat the same process to the G2 insertion.
6. Scan the “End Configuration”.
The position of G1/G2 character insertion: To select a char-
acter insert to the barcode. You can’t insert any character
while the installation is “0”
1. Scan the barcode of the “Start Configuration” and “G1
character insertion position”
2. Check the ASCII table to get the corresponding ASCII
code of the insertion position.
End Configuration
8
Start Configuration
3. Scan the “End Configuration”.
4. Repeat the same process to the G2 character insertion
position.
5. Scan the “End Configuration”.
Code Transmission: If your application needs to transmit the
code (barcode type ID) you have to set “ON” for this fea-
ture and the format is ID + Barcode data.
The Preamble Installation （Default：00）
Appendix A
The Postamble Installation （Default：00）
Appendix A
G1 Character Insertion （Default：00）
Appendix A
G2 Character Insertion （Default：00）
Appendix A
G1 Character Insertion Position（Default：00）
Appendix A
G2 Character Insertion Position（Default：00）
Appendix A
Code ID Transmission
ON
<OFF>
2.5 Other Installation
Scanning Precision: You can set to scan once or twice and
then transfer the bar code data. The twice will reduce the
error reading.
Bar Reverse Output Installation: This feature can read the
highlight barcode.
End Configuration
9
Start Configuration
Scanning Verify
<Single>
Double
Bar / Space Setting
<Bar = High>
Bar = Low
Laser Data Speed Up
<ON>
OFF
Chap.3 BAR-CODE INSTALLATION
3.1 UPC-A
Reading
OFF
Code ID (Default：F)
<20H-7EH>
UPC-A convert to EAN-13
<OFF>
Transmit Check Character
OFF
Truncate Leading Zero
<OFF>
<ON>
ON
<ON>
End Configuration
10
Autres manuels POSline Lecteur de codes-barres
POSline
POSline SM2410B Manuel utilisateur
POSline
POSline SW2500 Manuel utilisateur
POSline
POSline SM2410 Manuel utilisateur
POSline
POSline SL2050 Manuel utilisateur
POSline
POSline SM2450 Manuel utilisateur
POSline
POSline SC2110 Manuel utilisateur
POSline
POSline SM2410 Manuel utilisateur
POSline
POSline SC2120B Manuel utilisateur
POSline
POSline SM2440 Manuel utilisateur
POSline
POSline SC2160W Manuel utilisateur
Manuels Lecteur de codes-barres populaires d'autres marques
POSMicro
POSMicro Datalogic PowerScan D7100 Manuel utilisateur
Marson
Marson MT780 Guide de configuration rapide
NCR
NCR RealPOS Manuel utilisateur
Motorola
Motorola SE3300 Guide de configuration rapide
Element
Element P130BT Manuel utilisateur
Motorola
Motorola Symbol LS3008 Manuel d'installation et d'exploitation
