Popp Z-Wave 005107 Manuel utilisateur

Solar Powered Outdoor Siren

Manual

005107

Solar Powered Outdoor Siren – Manual

Quick Start..............................................................................................................................2

Product Description................................................................................................................2

Installation Guidelines ............................................................................................................3

Behavior within the Z-Wave Network......................................................................................3

Operating the Device..............................................................................................................4

Node Information Frame.........................................................................................................4

Associations ...........................................................................................................................4

Configuration Parameters.......................................................................................................4

Command Classes.................................................................................................................6

Technical Data .......................................................................................................................6

Explanation of Z-Wave specific Terms ...................................................................................7

Disposal Guidelines................................................................................................................7

Support...................................................................................................................................7

Quick Start

This device is a Z-Wave actuator. The device usually comes precharged. In case there is

not enough power please place the device into sun light for 10 minutes.

1. Open the case and turn on the power switch (ill.2 (A)) by moving it towards the

inclusion button (B). All LEDs will shine for a short moment to confirm.

2. Remove the metal mounting plate from the device.

3. Remove all protection foil from the device.

4. Turn your controller into inclusion mode with a short single click on the internal

inclusion button (ill.2 (B)).

The device supports secure communication if the controller supports secure communication

as well. Keeping the inclusion button pushed for 2 seconds includes the device unsecured

regardless of the controller’s capabilities. Once the siren is placed on the metal mounting

plate the tamper protection is activated. Do not remove the siren anymore unless it is

deactivated!

Product Description

This solar powered outdoor siren can be used without any additional power supply or

batteries. It can be installed on any place on the outside of the house and can be controlled

using Z-Wave. The device will issue a very loud sound (105 dBm) and in parallel some

stroboscope light as well. The siren is self-protecting. Removing the main device from the

mounting unit immediately starts the siren and also reports the tamper attempt to the Z-

Wave central controller. All communication between the Z-Wave controller and the siren is

encrypted and secured to protect against manipulation. Thanks to the large solar panel the

siren can be mounted on nearly every place outside the house, with direct or indirect sun

light. The siren is maintenance-free and water-proofed (IP56). The average solar energy of

one day keeps the device alive for up to 50 days (without using the siren). Additionally an

internal temperature sensor reports the temperature inside the siren’s enclosure.

Installation Guidelines

The siren can be placed on every location outside the home. Thanks to rating IP56 the

location does not even need to be dry but please make sure it is placed high enough so that

children do not accidently remove it. The device is self-protected against tamper and theft. In

a first step the mounting plate (ill. 1 (1)) is placed on the wall using the 4 screws provided. It is

recommended to mount the complete device 5 mm from the wall for better sound.

1. Open the case and turn on the power switch (ill.2 (A)) by moving it towards the

inclusion button (B). All LEDs will shine for a short moment to confirm.

2. Remove the metal mounting plate from the device.

3. Remove all protection foil from the device.

4. Turn your controller into inclusion mode with a short single click on the internal

inclusion button (ill.2 (B)).

Once included the enclosure of the siren is closed using the 6 screws. Finally the siren is

placed on the mounting plate.

Attention: As soon as the siren is placed on the mounting plate the tamper protection is

activated. The siren must not be removed from the plate anymore. The behavior in this

moment is defined by the configuration parameter No 1.

Behavior within the Z-Wave Network

On factory default the device does not belong to any Z-Wave network. The device needs to

join an existing wireless network to communicate with the devices of this network. This

(A) Power Button

(B) Inclusion Button

ill. 1

ill. 2

(D) Solar Module Connection

(E) Charge Connection

(F) Speaker Connection

process is called Inclusion. Devices can also leave a network. This process is called

Exclusion. Both processes are initiated by the primary controller of the Z-Wave network.

This controller will be turned into exclusion respective inclusion mode. Please refer to your

primary controller’s manual on how to turn your controller into inclusion or exclusion mode.

Only if the primary controller is in inclusion or exclusion mode, this device can join or leave

the network. Leaving the network – i.e. being excluded – sets the device back to factory

default.

Operating the Device

The siren can be turned on and off using wireless commands. To protect this communication

from misuse is strongly recommended to operate the siren in secure communication mode.

The secure communication is activated on default during inclusion unless explicitly

suppressed. When activated the siren will generate a 105 dB alarm sound and a flash light.

This behavior can be configured as well using configuration parameter 5. Make sure to

deactivate the tamper protection before removing an included siren from the mounting plate.

Back to Factory Default

To reset the device keep the inclusion button pushed for 10 seconds. After 5 seconds the

LED starts flashing and after another 5 seconds there is a short beep signaling the

successful reset back to factory defaults. Use this procedure only when the network primary

controller is missing or otherwise inoperable.

Node Information Frame

The Node Information Frame is the business card of a Z-Wave device. It contains

information about the device type and the technical capabilities. The inclusion and exclusion

of the device is confirmed by sending out a Node Information Frame. Beside this it may be

needed for certain network operations to send out a Node Information Frame.

Every click on the inclusion button (ill. 2 (B)) issues a Node Information Frame.

Associations

Z-Wave devices control other Z-Wave devices. The relationship between one device

controlling another device is called association. In order to control a different device, the

controlling device needs to maintain a list of devices that will receive controlling commands.

These lists are called association groups and they are always related to certain events

(e.g. button pressed, sensor triggers, ...). In case the event happens all devices stored in the

respective association group will receive a common wireless command.

Associations

Lifeline (max. nodes in group: 10)

Configuration Parameters

Z-Wave products are supposed to work out of the box after inclusion, however certain

configuration can adapt the function better to user needs or unlock further enhanced

features.

IMPORTANT: Controllers may only allow configuring signed values. In order to set values in

the range 128… 255 the value sent in the application shall be the desired value minus 256.

For example: to set a parameter to 200 it may be needed to set a value of 200 minus 256 =

minus 56. In case of a two byte value the same logic applies: Values greater than 32768

may needed to be given as negative values too.

Siren triggering mode (Parameter Number 1, Size 1)

Sets the tamper triggering mode when removed from the holder

Value

Description

The Siren triggers automatically when it's removed from the holder. Must be

turned off, using the button or from the controller (Default)

The Siren triggers automatically when it's removed from the holder and turns off,

when placed back on the holder

Siren doesn't trigger at all, when removed from the holder. Service Mode

Temperature adjustments (Parameter Number 2, Size 1)

Temperature correction. For positive value 10 = 1 °C, for negative value x = 256 - (T°C * 10).

Example, if need shift -2.6°C, value calculate: 256 - (2.6 * 10) = 230.

Value

Description

Disabled (Default)

1 – 127

In 0.1°C (Default 0)

128 – 255

-0.1°C

Send unsolicited temperature report (Parameter Number 3, Size 1)

Threshold temperature to send unsolicited report. 10 = 1°C

Value

Description

0 – 255

In 0.1°C (Default 10)

Send unsolicited temperature report after N wake up (Parameter Number 4, Size 2)

If the value is set, after N wake up number (measurement is every 4 minutes) the

temperature report will be sent. By default it's 15 = every 1 hour

Value

Description

Disabled

1 – 65535

Each Nth wake up time (Default 15)

Switch mode: siren only, flash only, flash + siren (Parameter Number 5, Size 1)

Value

Description

Siren only

Flash only

Flash + Siren (Default)

Added Auto OFF (Parameter Number 6, Size 1)

If the value is set, the siren will be switched off automatically after a defined alarm time.

Value

Description

No auto off

1-…

Minutes (Default 5)

Command Classes

Supported command classes

BASIC

Version 1

DEVICE RESET LOCALLY

Version 1

Z-WAVE PLUS INFORMATION

Version 2

MANUFACTURER SPECIFIC

Version 2

POWERLEVEL

Version 1

FIRMWARE UPDATE META DATA

Version 3

BATTERY

Version 1

VERSION

Version 2

SECURITY

Version 1

BINARY SWITCH

Version 1

BINARY SENSOR

Version 2

MULTILEVEL SENSOR

Version 5

ASSOCIATION GROUP INFORMATION

Version 1

CONFIGURATION

Version 1

ALARM

Version 5

ASSOCIATION

Version 2

Technical Data

IP Rating

IP 56

Battery Type

1 * Solar/ Storage battery: 7.4 V, 2,300 mA

Frequency

868.42 MHz (SRD Band)

Wireless Range

Up to 100 m outside, on average up to 20 m inside buildings

Explorer Frame Support

Device Type

Slave with routing capabilities

Generic Device Class

Binary Switch

Routing

FLiRS

Firmware Version

1.0

Explanation of Z-Wave specific Terms

•Controller is a Z-Wave device with capabilities to manage the network. Controllers are

typically gateways, remote controls or battery operated wall controllers.

•Slave is a Z-Wave device without capabilities to manage the network. Slaves can be

sensors, actuators and even remote controls.

•Primary Controller is the central organizer of the network. It must be a controller. There

can be only one primary controller in a Z-Wave network.

•Inclusion is the process of bringing new Z-Wave devices into a network.

•Exclusion is the process of removing Z-Wave devices from the network.

•Association is a control relationship between a controlling device and a controlled device.

•Wake up Notification is a special wireless message issued by a Z-Wave device to

announce that is able to communicate.

•Node Information Frame is a special wireless message issued by a Z-Wave device to

announce its capabilities and functions.

Disposal Guidelines

The product contains batteries. Please remove the batteries when the device is not used.

Do not dispose of electrical appliances as unsorted municipal waste, use separate collection

facilities. Contact your local government for information regarding the collection systems

available. If electrical appliances are disposed of in landfills or dumps, hazardous

substances can leak into the groundwater and get into the food chain, damaging health and

well-being.

Support

Should you encounter any problem, please give us an opportunity to address it before

returning this product. Most questions regarding Z-Wave wireless communication standard

can be answered through the international community at www.z-wave.info.

If your question can‘t be answered there, please contact us by email: info@popp.eu

While the information in this manual has been compiled with great care, it may not be deemed an

assurance of product characteristics. Popp & Co. shall be liable only to the degree specified in the terms

of sale and delivery.

The reproduction and distribution of the documentation and software supplied with this product and the

use of its contents is subject to written authorization from Popp & Co. We reserve the right to make any

alterations that arise as the result of technical development.

Phone: +44 (0) 20 7419 5726

eMail: i[email protected]

Web: www.popp.eu

Table des matières

Autres manuels Popp Système de sécurité

Popp

Popp Solar Outdoor Siren 2 Manuel utilisateur

Manuels Système de sécurité populaires d'autres marques

Inner Range

Inner Range Concept 2000 Manuel utilisateur

Climax

Climax Mobile Lite R32 Instructions de montage

CADDX

CADDX NX-6 Manuel utilisateur

FBII

FBII XL-31 Series Manuel utilisateur

Johnson Controls

Johnson Controls PENN Connected PC10 Manuel utilisateur

Aeotec

Aeotec Siren Gen5 Manuel utilisateur

Blaupunkt

Blaupunkt SA 2700 Manuel utilisateur

IDEAL

IDEAL Accenta Manuel du propriétaire

AJAX

AJAX DoubleButton Manuel utilisateur

Swann

Swann SW-P-MC2 Manuel utilisateur

Ecolink

Ecolink Siren+Chime Manuel utilisateur

Digital Monitoring Products

Digital Monitoring Products XR150 Manuel utilisateur

EDM

EDM Solution 6+6 Wireless-AE Manuel utilisateur

Highway Safety Group

Highway Safety Group EA401 Manuel utilisateur

Siren

Siren LED GSM Manuel utilisateur

Detection Systems

Detection Systems 7090i Instructions de montage

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manuel utilisateur

Siemens

Siemens FDM273 Manuel utilisateur