PolyScience IP-80 Manuel utilisateur

Operator’s Manual

IP-80 and IP-100 Immersion ProbeCoolers

110-810 06.07.18

110-810 1

Table of Contents

Introduction ................................................................................................................................................2

General Information ...................................................................................................................................2

General Safety Information....................................................................................................................2

Safety Recommendations ......................................................................................................................3

Unpacking Your Immersion Probe Cooler .............................................................................................3

Regulatory Compliance & Testing..........................................................................................................4

Contents ..................................................................................................................................................4

Controls & Components ............................................................................................................................5

Quick-Start ..................................................................................................................................................6

Installation & Startup ................................................................................................................................7

General Site Requirements ....................................................................................................................7

Positioning the Immersion Probe Assembly .........................................................................................7

Electrical Power...................................................................................................................................... 8

Normal Operation .......................................................................................................................................8

Turning Your Immersion Probe Cooler ON............................................................................................8

Main Operational Display........................................................................................................................9

Display Messages.................................................................................................................................... 9

Loss of Power Restart ............................................................................................................................9

Routine Maintenance & Troubleshooting ............................................................................................. 10

Cleaning Exterior Surfaces................................................................................................................... 10

Cleaning the Air Filter ..........................................................................................................................10

Draining Residual Oil from the Immersion Probe Assembly...............................................................10

Troubleshooting .................................................................................................................................... 11

Technical Information.............................................................................................................................. 12

Performance Specifications .................................................................................................................12

Equipment Disposal (WEEE Directive) ...................................................................................................13

Service & Technical Support ...................................................................................................................13

Warranty .................................................................................................................................................... 14

110-810 2

Introduction

Your Immersion Probe Cooler can be used to achieve low-temperature capability with non-

refrigerated circulating baths or boost the cooling capacity of refrigerated circulators. It is also

excellent for trapping and Dewar-type applications, making it an economical alternative to dry ice or

liquid nitrogen. A 6-ft. (1.83 m) flexible hose allows convenient placement of the cooling probe.

It will take you very little time to get your Immersion Probe Cooler installed and running. This

operator’s manual is designed to guide you quickly through the process. We recommend that you

read it thoroughly before you begin.

NOTE:

The Immersion Probe Cooler operates at maximum cooling performance. Maximum

temperature stability will be achieved in an agitated fluid and with a constant heat load. Allow

ample time to reach the lowest achievable temperature.

General Information

General Safety Information

When installed, operated, and maintained according to the directions in this manual and common

safety procedures, your Immerson Probe Cooler should provide safe and reliable cooling. Please

ensure that all individuals involved in the installation, operation, or maintenance of this unit read this

manual thoroughly prior to working with the unit.

This symbol marks chapters and sections of this instruction manual that are particularly

relevant to safety. When attached to the unit, this symbol draws attention to the relevant

section of the instruction manual.

This symbol advises you of danger from electricity or electric shock.

This symbol marks information that is particularly important.

This symbol indicates alternating current.

These symbols on the Power Switch / Circuit Breaker indicate that they place the main power

supply ON / OFF.

This symbol on the Power Key indicates that it places the unit in a standby mode. It DOES

NOT fully disconnect the unit from the power supply.

This symbol indicates a protective conductor terminal.

Read all instructions pertaining to safety, set-up, and operation.

Proper operation and maintenance is the user’s responsibility.

110-810 3

Safety Recommendations

To prevent injury to personnel and/or damage to property, always follow your workplace’s safety

procedures when operating this equipment. You should also comply with the following safety

recommendations:

WARNING:

• Always connect the power cord on this unit to a grounded (3-prong) power outlet. Make certain

that the outlet is the same voltage and frequency as your unit.

• Never operate the unit with a damaged power cord.

• Always turn the unit OFF and disconnect Mains power before performing any maintenance or

service.

WARNING:

• Never touch the immersion probe assembly while the unit is operating.

• Always allow the immersion probe to warm to ambient temperature before repositioning or

working on the unit.

• Do not move the immersion probe assembly while the unit is operating.

Unpacking Your Immersion Probe Cooler

Your Immersion Probe Cooler was packed in a special carton. You should keep the packaging, along

with all packing materials, until the unit has been installed and you are certain it is working properly.

CAUTION:

Remove any loose packing material that may have clung to the base or wand

assembly.

WARNING:

Keep unit upright when moving. Be sure to follow your company’s procedures and

practices regarding the safe lifting and relocation of heavy objects.

In the unlikely event that the unit was damaged or does not operate properly, contact the company

where your Immersion Probe Cooler was purchased.

110-810 4

Regulatory Compliance & Testing

cCSAus

(120V, 60Hz units)

UL 61010-1 (3rd Edition) - Safety Requirements for Electrical Equipment for Measurement, Control,

and Laboratory Use - Part 1: General Requirements

CAN/CSA-C22.2 No 61010-1-12 - Safety Requirements for Electrical Equipment for Measurement,

Control, and Laboratory Use - Part 1: General Requirements

Product meets CAN ICES-1/NMB-1 and FCC Part 15

This device complies with part 15 of the FCC rules. Operation is subject to the following two

conditions: 1. This device may not cause harmful interference, and 2. This device must accept any

interference received, including interference that may cause undesired operation.

IEC/CE

(230V, 50Hz units; 100V, 50/60Hz units)

Machinery Directive 2006/42/EC Annex I

IEC 61010-1:2010 - Safety Requirements for Electrical Equipment for Measurement, Control, and

Laboratory Use - Part 1: General Requirements

EN 61010-1:2010 - Safety Requirements for Electrical Equipment for Measurement, Control, and

Laboratory Use - Part 1: General Requirements

EMC Directive 2014/30/EU

EN 61326-1:2013 - Electrical Equipment for Measurement, Control and Laboratory Use - EMC

Requirements - Part 1: General Requirements

RoHS Directive 2011/65/EU

EN 50581:2012 - Technical Documentation for The Assessment of Electrical and Electronic

Products With Respect to The Restriction of Hazardous Substances

Highly Accelerated Life Test (HALT) and Vibration Tests per ASTM D4169-8

(All units)

Contents

The Following Items Have Been Included With Your Immersion Probe Cooler:

• Operator’s Manual

• IEC Electrical Cord

• Certificate of Compliance

110-810 5

Controls & Components

IMPORTANT:

The temperature display is for reference only. The actual temperature of the

immersion probe will be colder than the displayed temperature.

Cold Finger Immersion Probe Flexible Immersion Probe 1.75” Rigid Coil Probe

Power Key

Temperature Display

Air Filter

Compartment

Power Switch /

Circuit Breaker

IEC Electrical Connection

Rigid Coil Immersion Probe

(3” rigid coil shown)

Identification Label

Immersion Probe

Assembly

110-810 6

Quick-Start

Position Immersion

Probe

Connect power. See

Identification Label.

Turn main power ON.

Turn Standby power ON.

Allow approximately 10

minutes for the system

to begin the cooling

process.

Allow approximately 1

hour for system to reach

-80°C (IP-80) or

-90°C (IP-100).

(typical)

CAUTION:

Moving Immersion Probe Cooler while unit is operating may result in damage.

110-810 7

Installation & Startup

Your Immersion Probe Cooler is designed to be simple to set-up and install. No tools are required.

General Site Requirements

Locate the unit on a level surface, free from drafts and out of direct sunlight. Do not place it

where there are corrosive fumes, excessive moisture, high room temperatures, or where

excessive dust is present.

The unit must be a minimum of 6 inches / 15.24 cm away from walls or vertical surfaces so that

airflow around the unit is not restricted. It should not be placed in cabinets or where exiting

warm air or warm air from other devices will be drawn into the air intake on the front of the unit.

NOTE:

It is recommended that your unit be run in ambient temperatures below 95°F / 35°C.

While the unit will operate at higher ambient temperatures, it may not be able to achieve

maximum cooling performance.

Positioning the Immersion Probe Assembly

When installing the unit, make sure that the Immersion Probe Assembly is properly positioned. It

should not be twisted. Incorrect positioning of the Wand Assembly will cause your Immersion

Probe Cooler to perform below specifications.

CAUTION:

Moving the Immersion Probe Assembly while the unit is operating may result in

damage.

110-810 8

Electrical Power

WARNING: IMPORTANT INFORMATION FOR 100V APPLICATIONS

On 100V 50Hz applications a step-up transformer IS NOT NEEDED and MUST NOT be used.

On 100V 60Hz applications a step-up transformer MUST be used.

WARNING:

Make certain that the electrical outlet is the same voltage and frequency as your

unit. The correct voltage and frequency for your unit are indicated on the Identification Label on

the back panel.

WARNING:

The use of an extension cord is not recommended. If one is necessary, it must be

properly grounded and capable of handling the total wattage of the unit. The extension cord

must not cause more than a 10% drop in voltage to the unit.

Attach the 6-ft / 1.8 m power cord to the IEC electrical connector on the back of the unit and then

plug the male connector into the Mains electrical outlet.

Place the Power Switch / Circuit Breaker on the back of the

Immersion Probe Cooler in the ON position. Three decimal points

will appear on the Temperature Display. This indicates that the unit

is in Standby mode.

Your Immersion Probe Cooler is now ready to begin normal

operation.

Normal Operation

Turning Your Immersion Probe Cooler ON

Press the Power Key on the front panel. After a brief initialization

message, the probe temperature will appear on the Temperature

Display. After five minutes, the first stage compressor and fan will

turn on to begin the cooling process. During this start-up phase, the

displayed temperature will remain near or at ambient temperature.

After approximately 10 minutes, the second stage compressor will

turn on, refrigerant will begin circulating through the system, and

the displayed temperature will begin decreasing. It generally takes approximately 60 minutes from

power up for the IP-80 to reach -80°C or for the IP-100 to reach -90°C.

NOTE:

The Immersion Probe Cooler operates at maximum cooling performance.

IMPORTANT:

To protect its compressors from damage, the Immersion Probe Cooler

incorporates a special safety switch that delays compressor startup for 10 minutes

whenever power is applied. This 10 minute delay will occur even when power is only

momentarily disrupted.

110-810 9

Main Operational Display

The actual temperature of the immersion probe is displayed in

degrees C on the unit’s digital readout. Due to the location of the

temperature sensor, this temperature is a few degrees warmer

than the surface temperature of the immersion probe.

Display Messages

Temperature Display

Description

Standby Mode

— Indicates that the Power Switch / Circuit Breaker on

the back panel is in the ON position and unit is ready to operate.

Power On / Start-Up

— Appears briefly when the Immersion Probe

Cooler is turned ON by pressing the Power Key on the front panel. The

information represents the firmware version.

Main Operational Display

— Indicates unit is ON and operating.

Displayed temperature is in degrees C.

Note: Displayed temperature is to one tenth of a degree (X..X) until it

reaches -10°.

Warning Display

— Indicates that the external temperature sensor is

not functioning properly. Unit will continue to cool.

Loss of Power Restart

In the event that electrical power is disrupted during operation, the unit will begin operating

automatically when power is restored. As with normal start-up, it will take approximately 60 minutes

for the IP-80 to reach -80°C or the IP-100 to reach -90°C.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels PolyScience Équipement de laboratoire

PolyScience

PolyScience LX Immersion Circulator Manuel utilisateur

PolyScience

PolyScience MX07R-20 Manuel utilisateur

PolyScience

PolyScience Histology Bath Manuel utilisateur

PolyScience

PolyScience WBE20A11B Manuel utilisateur

PolyScience

PolyScience WB05A11B Manuel utilisateur

PolyScience

PolyScience DuraChill 58 Series Manuel utilisateur

PolyScience

PolyScience MX-CA12E Manuel utilisateur

PolyScience

PolyScience MX-CA11B Manuel utilisateur

PolyScience

PolyScience 4100 Series Manuel utilisateur

PolyScience

PolyScience WBE10A11B Manuel utilisateur

Manuels Équipement de laboratoire populaires d'autres marques

Qiagen

Qiagen DML 3000 Manuel utilisateur

Queensgate

Queensgate NANOSCAN OP400 Manuel de programmation

Conviron

Conviron GEN1000-GE Manuel utilisateur

Parr Instrument

Parr Instrument 4560 Mode d’emploi

IKA

IKA IC control Manuel utilisateur

Integra

Integra DOSE IT Manuel utilisateur

Agilent Technologies

Agilent Technologies 5800 ICP-OES Manuel utilisateur

Endress+Hauser

Endress+Hauser Cleanfit CPA875 Manuel utilisateur

NI PXI-5422 Manuel

Collomix

Collomix Aqix Manuel utilisateur

SPEX SamplePrep

SPEX SamplePrep 6875 Freezer/Mill Series Manuel utilisateur

Ocean Insight

Ocean Insight FLAME-NIR+ Manuel utilisateur

Parker

Parker ALIGN-MG-NA Manuel utilisateur

BD 644787 Manuel utilisateur

DENTAURUM

DENTAURUM Compact Megaplus Manuel utilisateur

Biuged Laboratory Instruments

Biuged Laboratory Instruments BGD 626 Manuel utilisateur

VWR

VWR SAS Super IAQ Manuel utilisateur

illumina

illumina MiSeqDx Manuel utilisateur