Polyision PS2W-SA series Manuel utilisateur

Outdoor High Speed Dome System

User Manual

Contents

Before installing

Key features

Configure, fix and wire

Basic speed dome operation

Programming the speed dome

The keyboard shortcuts of speed dome

Parts and dimensions

Wiring schematic

Specifications

Outdoor High Speed Dome System

Appendix Of Outdoor High Speed Dome System

Before installing

·Installation should be carried out only by qualified personnel and in accordance with

any wiring regulations in force at the time.

·The speed dome is heavy and could cause injury if not correctly mounted in

accordance with these instructions. Use only the fittings supplied with the speed

dome and ensure that all lanyard safety cables are connected correctly during

installation.

·Adequate protection against lightning strikes and power surges must be installed to

prevent damage to the speed dome.

·Any safety warnings on the product and in these instructions must be adhered to.

·If cleaning is necessary, disconnect power to the speed dome first. Do not use

abrasive cleaners, as these will cause damage to the cover and cause poor image

quality. Use a damp cloth to gently clean the dome cover and dry off with a soft

clean cloth.

·Do not use any brackets, mounts or other accessories not specifically designed for

use with this speed dome.

·Do not attempt to service or repair the speed dome as opening or removing covers

may expose dangerous voltages or other hazards. Refer all servicing to qualified

service personnel.

Key features

Presets

Up to 254 sets of positional and zoom level information can be stored as

presets. These can be called manually by the operator, automatically by an

alarm input, or grouped to form a sequence of actions to run automatically.

Each preset can also be programmed with the following:

Alarm action - relay outputs can be triggered when particular presets are

called

Title - each preset can be titled with up to 10 characters so that zones can

easily be identified

Pattern tours

Any dome movement can be recorded - and subsequently played back - as

four separate pattern tours. These can be played back individually or

grouped to form a sequence of tours.

Scan function

Scan is a useful feature when, for example, the operator wishes to ‘patrol’ a

perimeter fence. you can choose any two points to define as start point and

end point , the scan function will smoothly and accurately move from one

end to the other and then back again in a repeating sequence.

Group function

The group function is a powerful feature which allows the operator to define

a sequence of speed dome actions to form an automatic patrol sequence.

Actions can be a mix of preset positions, pattern tours and scan functions.

Up to 8 groups can be defined and each group can have up to 20 actions

which repeat indefinitely until interrupted by the operator or an alarm input.

Specific parameters such as preset speed, dwell time and action loop can

also be specified.

Speed can

be adjusted as necessary and up to 8 scan functions can be defined.

Privacy zones

By defining a privacy zone, sensitive scenes such as windows can be

masked off so they cannot be viewed by the operator. Up to 8 privacy

zones can be defined. Privacy zone size adjusts automatically depending

on the speed dome zoom level.

Alarm inputs and outputs

This speed dome has 8 alarm inputs and 4 alarm outputs. Any alarm input

can be set to call a predefined preset, scan function, pattern or group. Any

preset can be configured to activate any or all of the alarm outputs. For

example, a PIR detector connected to alarm input 1 could call preset 7 to

view that particular scene whilst activating an external lamp connected to

relay 1 and an external siren connected to relay 3.

On Screen Display (OSD)

The operator can choose if any or all of the following information is

displayed on screen during normal speed dome operation.

Preset status and title

Speed dome position coordinates and zoom level

Alarm I/O status

Time and Date

Speed dome ID

The speed dome also has a full on screen menu setup allowing quick and

easy configuration of all the speed dome features.

Powerful park function

The speed dome can be configured to run a specified scan function, pattern

tour, group or preset after a defined period of inactivity.

Auto Adapt Power: The speed dome can automatic adapt the power

supply between DC12V~24V and AC12V~24V.

Configure, fix and wire

1. Remove the foam packing pieces

Before proceeding with installation, the speed dome foam packing

pieces must be removed. Remove the outer dome cover with the tool

supplied and carefully remove the foam packing pieces. When

handling the dome cover, always wear the gloves supplied to avoid

getting fingerprints on the outer dome cover.

Foam

1. Wearing the gloves and using the supplied

tool, remove the outer dome cover.

2. Remove the foam pieces from the camera

module.

Foam

Outdoor High Speed Dome System

2. Fix the bracket

1. Fix the supplied mounting template, taking

account of any pipework, cables, overhangs

etc. that may obstruct the bracket once fitted.

2. After making suitable checks for buried

pipes and cables, drill fixing holes suitable for

the bolts supplied with the speed dome.

3. Remove the junction box cover. Using the

supplied bolts and tool, firmly fix the bracket.

Pendent option

5. Bring the speed dome up to the bracket. 6. Tighten the three screws to fix the speed

dome and ensure the lanyard safety chain is

properly connected.

4. Feed the speed dome cable through the

bracket.

Lanyard

3. Wire up the junction box

1.Video output

13.ADDRESS ID SWITCH

Junction box PCB detail

4.DC 12~AC 24V Power

5.12V DC OUTPUT

6.AUDIO IN

2.SPEED DOME CABLE

8.AUDIO OUT

7.AUDIO GROUND

9.Rs485

10.Rs422

14.BAUD RATE SWITCH

15.RS485/422 SWITCH

12.ALARM INPUT

11.ALARM OUT

3.SPEED DOME CABLE

(1).Video output: Standard 1V P-P,Use good quality 75

Ohm cable terminated with a BNC connector.

(2).(3)Speed Dome Cable: the interface connected with

speed dome.

(4).Auto Adapt Power: this can automatic adapt the

power supply between .DC12V~24V and AC12V~24V

(5).12V DC output: an extra 12V DC power is available

for other devices, but please be Kindly noted that the

maximum power of the other device is 6W and 500mA.

(6).(7).(8)Audio In/Out/Ground:standard audio In/Out

interface, this function is just for IP speed dome(only IP

model has these functions).

(11).(12).Alarm Input/Output:8 Alarm Input and 4

Output.

(13)Address ID switch:

OFF

---

OFF

---

OFF

---

OFF

---

OFF

---

OFF

---

OFF

---

OFF

---

255

12345678 D I P

2 4 8 1 6 3 2 6 4 1 2 8 Va l I D

Note: ID 0 should not be used. Where multiple speed domes

are connected, a unique ID must be assigned to each one.

1 2 3 4 5 6 7 8

Factory default

switch positions

Speed dome ID is set

using standard

binary notation

(14).(15).Baud rate/RS485/422 switch:

1 2 3 4

Factory default switch positions

RS4 85/42 2

BAUD R ATE

Baud rate DIP switch table

1 2 3 4

OFF OFF

ON OFF

OFF ON

2400 bps

4800 bps

9600 bps

38400 bps

P r o t o c o l / R a t e

3 4 Factory default switch positions

RS485/422 SETUP

The switch number 1

on RS485

off Rs422

(9).(10).RS485/422:Using different communication

method according to the RS485/422 switch. 4

4. Complete the install

1a - wall bracket option. After making all the

connections to the PCB, fit the junction box

cover with the four screws.

Note: when fixing the cover to the junction box, ensure that the seal is also

fitted properly and that none of the cables are trapped.

1b - pendent option. After making all the

connections to the PCB, raise the dome

assembly to the junction box, connect the

dome cable to the PCB and fix with the four

screws.

Seal

0 7 / J A N / 2 0 0 7

0 9 : 3 7 : 1 5

C A M 1

O : - 2 3 -

I : 1 2 3 4 5 6 7 8

3 0 7 / 4 6 / x 3

P R E S E T 3R E C E P T I O N

Basic speed dome operation

Understanding the On Screen Display (OSD)

There are many different PTZ keyboards and DVR systems capable

of controlling this speed dome, and it would be impossible to

describe them all here. Therefore, examples given in the following

pages are based on the more popular control equipment available.

Whilst the principles of operation are the same, regardless of the

control equipment used, reference may need to be made to the

manual supplied with your particular control equipment.

CAMERA ID: Shows the

current ID as defined by the

dip switch settings

ALARM I/O: Shows which

alarm inputs and outputs are

active

DATE/CLOCK: Shows

current time and date

PTZ INFORMATION: The current

pan/tilt position in degrees and

the current zoom level

ACTION TITLE: Shows

current speed dome

action

Preset - 191 - DISPLAY AUTO

Preset - 193 - DISPLAY ON

Preset - 194 - MASK DISPLAY OFF

Preset - 195 - MASK DISPLAY ON

Preset - 190 - Enter switch focus modes among auto,semiauto,manual.

Enter

P RE S E T 3P AR K I N G B AY 1

S ET P R E S E T1

To program a preset position, move the speed

dome to the desired scene and zoom level

and press:

SET - XXX - ENTER

Where XXX is a preset number between 1 &

(but note that preset 95 is reserved and

cannot be used). Confirmation is displayed on

the OSD.

254

To delete a preset position, press:

CLEAR - XXX - ENTER

Where XXX is a preset number between 1 &

(but note that preset 95 is reserved and

cannot be used). The preset position is

cleared from memory.

254

To reprogramme a preset position, follow the

steps for programming a preset - it is not

necessary to delete the old preset position first

To go to a preset position thats already

been programmed, press:

PRESET - XXX - ENTER

Where XXX is a preset number between 1 &

254 (but note that preset 95 is reserved and

cannot be used). The speed dome moves to

the preset position. Confirmation and preset

title (if defined) is displayed on the OSD.

O : - - - -

I : 1 2 3 4 5 6 7 8

3 2 5 / 3 7 / x 1

O:----

I : 1 2 3 4 5 6 7 8

325/37/x3

0 7 / J A N / 2 0 0 7

1 2 : 3 8 : 0 5

C AM 1

07/JAN/2007

1 2 : 4 2 : 2 2

C AM 1

the keyboard shortcuts of speed dome

Once the pattern tours, scan and groups have been

programmed in the speed dome setup menu, they can all be

accessed directly from the PTZ control equipment by using the

following sequences.

1. To start a PATTERN tour press:

PRESET - 13X - ENTER

Where X is a PATTERN tour number between 1 & 4

The selected PATTERN tour will run indefinitely until a manual movement is made by the

operator or an alarm input is received.

2. To start a SCAN function, press:

PRESET - 14X - ENTER

Where X is a SCAN function number between 1 & 8

The selected SCAN function will run indefinitely until a manual movement is made by the

operator or an alarm input is received.

3. To start a group, press:

PRESET - 15X - ENTER

Where X is a GROUP number between 1 & 8

The selected GROUP will run indefinitely until a manual movement is made by the operator

or an alarm input is received.

All the other shortcuts please see below table:

ShutCuts Function

Preset - 95 - Enter Call OSD Menu

Preset - 171 - Enter Call WDR

Preset - 173 - Enter Call Auto WhiteBalance

Preset - 174 - Enter Call Brightness

Preset - 175 - Enter Call Digital Slow Shutter

Preset - 176 - Enter Call DNR

Preset - 177 - Enter Call Jog Max Speed

Preset - 179 - Enter Call High Light Control

Preset - 180 - Enter Call Day/Night

functions

First, we assume your keyboard using key PRESET to

call preset.

Display setup

System information

The speed dome setup menu allows the operator to customise and

program all aspects of speed dome operation. All menu settings are

retained in non-volatile memory so if power is lost to the speed dome

for any reason, all settings will be retained.

R O O T M EN U

-----------------------------

< S Y S TE M IN FO R M A T I O N >

< D I S PL AY S ET U P >

< M O T IO N SE TU P >

< C A M ER A SE TU P >

< F U N CT IO N SE T U P >

< S Y S TE M SE TU P >

< H E L P>

E X I T

DISPLAY SETUP

-----------------------------

CAMERA ID

PTZ INFORMATION

ACTION TITLE

PRESET LABEL

ALARM I/O

DATE/TIME

BACK

EXIT

SYSTEM INFORMATION

-----------------------------

FIRMWARE VER

COLOUR SYSTEM

PROTOCOL

BAUD RATE

ADDRESS

BACK

EXIT

To access the speed dome setup menu, key:

SHOT - 95 - ENTER

To navigate the main menu, move the joystick

up / down to choose a menu item or change

settings within a menu item.

To enter a menu item or confirm a new setting,

key: NEAR

To exit a menu item or cancel a new setting,

key: FAR

Where a menu item is surrounded by

brackets, it indicates that there is a sub menu.

Where a menu screen shows EXIT, selecting

this option will exit the menu and the speed

dome will return to normal operation. Where a

menu screen shows BACK, selecting this

option will return to the higher menu level.

The main menu has seven options:

<SYSTEM INFORMATION> - Provides

information such as firmware version, protocol

and ID values as defined by the dip switch

settings.

<DISPLAY SETUP> - Allows the operator to

specify which On Screen Display information

is shown during normal operation. Also allows

privacy zones to be defined.

<MOTION SETUP> - Set the general

functions of pan/tilt motion, for example,

preset lock, power up action, auto flip and jog

speed etc.

<CAMERA SETUP> - Allows all operating

features of the speed dome to be programmed

and managed. Also allows settings for the

camera module to be changed

<FUNCTION SETUP> - Set the Preset/Scan/

Pattern/Group/Schedule function.

<SYSTEM SETUP> - Allows various speed

dome settings to be reset to factory defaults

Shows information and current configuration.

From the main menu, use the joystick to

highlight SYSTEM INFORMATION and key:

NEAR

To return to the main menu, highlight BACK

and key: NEAR

To exit the setup menu completely, highlight

EXIT and key: NEAR

From the main menu, use the joystick to

highlight DISPLAY SETUP and key: NEAR

CAMERA ID (ON / OFF) - shows camera ID

according to the DIP switch settings, eg

CAM 1.

PTZ INFORMATION (ON / OFF / AUTO) -

shows the current pan / tilt position in degrees

and the current zoom level.

ACTION TITLE (ON / OFF / AUTO) - shows

current speed dome action, eg PRESET3.

PRESET LABEL (ON / OFF / AUTO) - shows

preset title (if defined) when a preset is called.

ALARM I/O (ON/OFF) - shows real time

status of the alarm inputs and outputs.

DATE/TIME(ON/OFF) -show date and time

<PRIVACY ZONE> - sub menu to setup the

speed dome privacy zones

Highlight the item to modify and key: NEAR

Use the joystick to change the setting and key:

NEAR to save or: FAR to cancel.

Note: If the auto option is chosen, the relevant

information is displayed for a few seconds

before disappearing.

4.01W36

PAL

AUTO

2400

AUTO

Programming the speed dome

Privacy zone

PRIVACY ZONE

- - - - -- -- -- - - - - - - - - - -- -- -- - - - -

MASK NO.

DISPLAY

CLEAR

BACK

EXIT

From the display setup menu, use the joystick

to highlight PRIVACY ZONE and key: NEAR

ZONE NO. (1-8) - shows the privacy zone

currently being modified.

DISPLAY - determines whether the privacy

zone is displayed during normal operation.

<EDIT ZONE> - allows the operator to define

the privacy zone.

Highlight the item to modify and key: NEAR

Use the joystick to change the setting and key:

NEAR to save or: FAR to cancel.

O F F

C L E A R

MOTION SETUP

-----------------------------

PRESET LOCK OFF

BACK

EXIT

PWR UP ACTION ON

AUTO FLIP OFF

JOG MAX SPEED 240

JOG DIRECTION INVERSE

Motion setup

PARKING ACTION SETUP

- - - - -- -- -- - - - - - - - - - -- -- -- - - - -

PARK ENABLE

WAIT TIME

PARK ACTION

ACTION NO ___

B A C K

E X I T

OFF

00:10:00

preset

From the motion setup menu, use the joystick

to highlight PARKING ACTION SETUP and

key: NEAR

PARK ENABLE - when set to ON, the speed

dome will run the specified park action after

the wait time has elapsed

WAIT TIME - can be set between one minute

and 4 hours. If no manual control occurs

during this time, the park action will run

PARK ACTION - choose the action to run after

the wait time has elapsed. This can be return

to home position, go to a preset or run a scan,

pattern or group.

Highlight the item to modify and key: NEAR

Use the joystick to change the setting and key:

NEAR to save or: FAR to cancel.

Parking action setup

From the dome camera setup menu, use the

joystick to highlight MOTION SETUP and key:

NEAR

PRESET LOCK - when set to ON, preset

programming directly from the keyboard is

disabled to prevent tampering

PWR UP ACTION - you can set this with

LASTACT/PRESET/SCAN/PATTERN/

GROUP/OFF,the speed dome will resume the

setting operation when power is restored after

a power failure

AUTO FLIP (ON / OFF) - when set to ON, the

dome will flip 180 degrees when the tilt

position reaches 90 degrees.

JOG MAX SPEED - determines the maximum

speed in degrees / second the dome will move

during manual operation

JOG DIRECTION (INVERSE / NORMAL) -

when set to normal, the pan direction is

opposite to the joystick movement.when set

to inverse, the scan direction is the same with

the joystick movement.

<PARKING ACTION SETUP> - Configure

actions that run automatically after a defined

period of inactivity

Highlight the item to modify and key: NEAR

Use the joystick to change the setting and key:

NEAR to save or: FAR to cancel. 8

Edit mask

E D I T M AS K 1

-----------------------------

M O V E T O TA RG ET P O S I T I O N

[NEAR:SELECT/FAR:CANCEL]

E D I T M AS K 1

-----------------------------

[ : A D J US T MA SK W I D T H ]

[ : A D J US T MA SK H E I G H T ]

[NEAR:SAVE /FAR:CANCEL]

From the privacy zone menu, use the joystick

to highlight EDIT MASK and key: NEAR

Use the joystick to move the speed dome to

the approximate position and zoom level for

the privacy zone and key: NEAR to select or

FAR to cancel and return to the privacy zone

menu.

Move the joystick left and right to finely adjust

the width of the privacy zone and up and down

to finely adjust the height.

To save the privacy zone, key: NEAR or key:

FAR to cancel.

From the dome camera setup menu, use the

joystick to highlight CAMERA SETUP and key:

NEAR

FOCUS MODE

MANUAL - the operator must focus the

camera manually using the NEAR and FAR

keys.

SEMIAUTO -

the

camera automatically focuses during normal

PTZ movement but preset focus information is

stored when a preset is programmed and

recalled each time the preset is called.

AUTO - the module auto focuses continually

DIGITAL ZOOM (ON / OFF) - allows user to

set the digital zoom as ON or OFF.

FLICKERLESS (ON / OFF) - should be set to

ON when used in certain lighting conditions

(EG Fluorescent lighting) to prevent picture

flicker.

COLOUR (ON/OFF) - switches the module

between colour and b/w mode.

the camera automatically focuses,

but it could be switch to “Manual” mode by

pressing “Near” or “Far”, and it could be

switched back to “Auto” mode by move the

joystick up/down, right/left, or zoom in/out, and

the factory default is in “Semioauto” mode.

ZOOM CAMERA SETUP

-----------------------------

FOCUS MODE

DIGITAL ZOOM

FLICKERLESS

COLOUR

STABILIZE OFF

DETIAL 0

HR 7

BACK

EXIT

Zoom camera setup

SEMIAUTO

OFF

STABILIZE(on/off) - the stabilize function

internally detects shaking of the image

due to camera shaking, and performs

digital compensation processing to

suppress this shaking and stabilize the

image output.

Detail - this function adjusts the

enhancement of the edge of objects

in the picture.

Ce manuel convient aux modèles suivants

Table des matières

Manuels Système de sécurité populaires d'autres marques

Inner Range

Inner Range Concept 2000 Manuel utilisateur

Climax

Climax Mobile Lite R32 Instructions de montage

CADDX

CADDX NX-6 Manuel utilisateur

FBII

FBII XL-31 Series Manuel utilisateur

Johnson Controls

Johnson Controls PENN Connected PC10 Manuel utilisateur

Aeotec

Aeotec Siren Gen5 Manuel utilisateur

Blaupunkt

Blaupunkt SA 2700 Manuel utilisateur

IDEAL

IDEAL Accenta Manuel du propriétaire

AJAX

AJAX DoubleButton Manuel utilisateur

Swann

Swann SW-P-MC2 Manuel utilisateur

Ecolink

Ecolink Siren+Chime Manuel utilisateur

Digital Monitoring Products

Digital Monitoring Products XR150 Manuel utilisateur

EDM

EDM Solution 6+6 Wireless-AE Manuel utilisateur

Highway Safety Group

Highway Safety Group EA401 Manuel utilisateur

Siren

Siren LED GSM Manuel utilisateur

Detection Systems

Detection Systems 7090i Instructions de montage

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manuel utilisateur

Siemens

Siemens FDM273 Manuel utilisateur