Polycom Vortex EF2201 Instructions d'installation et d'utilisation

Installed Voice Business Group

Application Note:

Using Crestron Viewport with Vortex and

Echofree Devices

Polycom  and the Polycom logo are registered trademarks of Polycom, Inc.

ASPI, Vortex, VS4000, Viewstation, and iPower are

registered trademarks of Polycom, Inc.

All other brand names, product names, and trademarks are the

sole property of their respective owners

Table of Contents

TABLE OF CONTENTS ..................................................................................................2

INTRODUCTION..............................................................................................................3

RS-232 HARDWARE........................................................................................................3

STARTING VIEWPORT .................................................................................................3

COMMAND SYNTAX......................................................................................................4

SENDING AND RECEIVING COMMANDS ................................................................5

TECHNICAL SUPPORT..................................................................................................7

Polycom IVB Contact Information ......................................................................................................7

Introduction

In addition to the Console window of Conference Composer, Crestron Viewport is

a great way to verify that the Crestron control system is sending the proper

commands to the EF Device as well as receiving the proper acknowledgments.

Here are some tips in setting up the Viewport window to communicate with an

EF Device.

RS-232 Hardware

The communication between the EF Device and a host controller is conducted via

the RS-232 port on the back panel of the EF Device. The RS-232 port operates at

the following settings:

•Bit Rate (bps): 9600 (default), 19200, or 38400

•Data Format: 8 data bits, no parity, 1 stop bit (8N1)

•Flow Control: none (default) or hardware (RTS, CTS)

Baud rates higher than 9600 are only supported on EF2280 or

EF2241 units that have Software Version 2.00 or higher.

Note that although the flow control setting is user selectable to

none

hardware

, hardware flow control must be used when updating the firmware of

the EF Device. This means that while a 3-wire RS-232 cable (RX, TX, GND) is

acceptable for control of the EF Device, the minimum cable for updating

firmware should contain 5 wires (RX, TX, RTS, CTS, GND).

Starting Viewport

Open up Viewport by going to START,PROGRAMS,CRESTRON SIMPL WINDOWS and

clicking VIEWPORT.Alternately, you can open SIMPL Windows and click on the

Viewport Icon .

Once Viewport is open, click on DIAGNOSTICS, and ESTABLISH COMMUNICATIONS (FIND

RACK). You should see a window open up that verifies that the PC has been able

to communicate with the control system:

Command Syntax

You can use the PASSTHRU command to send and receive data from an EF

Device. The syntax is as follows:

PASSTHRU COM x com mode baud rate data bits parity

stop bits flow control

where:

xis the Com Port

com mode is 232, 422, or 485 mode (default is 232)

baud rate is any data rate from 300-115200 bps (default is 9600)

data bits is the word length (default is 8)

parity is a way to detect transmission errors (default is N)

stop bits is the number of bits to signal the end of transmission (default is 1)

flow control is either hardware or software handshaking (default is NONE).

You can send a PASSTHRU ? command if you need more help on

the syntax.

•For an EF200 and EF1210, we recommend the following PASSTHRU

command:

PASSTHRU COM x 9600

where xis the com port of the Crestron control system.

•For an EF2280 and EF2241, we recommend the following PASSTHRU

command:

PASSTHRU COM x baud rate

where xis the com port of the Crestron control system and baud rate is

any data rate of 9600, 19200, or 38400 bps.

You don't have to type these settings in Viewport. You can click on

FUNCTIONS,ENTER PASSTHROUGH MODE (CNX/2 SERIES) and set every

value that was described above. However, in our testing with a

CP2, we received an Invalid Parameters response from the CP2

when we tried to execute that feature.

Sending and Receiving

Commands

Once you've sent the proper PASSTHRU command, click Setup and make sure

that LOCAL ECHO is checked and DISPLAY IN HEX MODE is unchecked. CR TO CR/LF

(OUTGOING) is optional.

Now, you should be able to send any valid EF Device command to the unit.

Here, a ***PING command has been sent to a EF2280 at a baud rate of 38400.

Note that by checking the LOCAL ECHO option, that feature caused the PASSTHRU

command to display double characters.

Without LOCAL ECHO checked, here is the same window as displayed in Viewport.

You do not have to use the LOCAL ECHO option when sending commands;

however, it makes sending commands easier since you can see what you've

typed locally.

TECHNICAL SUPPORT

For Polycom products (EF2280, EF2241, EF1210, EF400, EF200):

•Call 404-892-3200 between 9 am to 6 pm and Press 3

•Send an email to [email protected]

For other Polycom products (VS4000, Viewstation FX, iPower, etc.):

•Call 408-474-2048

•Send an email to: pa[email protected]

POLYCOM IVB CONTACT INFORMATION

Our address is:

1720 Peachtree Street, NW

Suite 220

Atlanta, GA 30309

404-892-3200 Phone

404-892-2512 Fax

Autres manuels pour Vortex EF2201

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Polycom Accessoires pour téléphone

Polycom

Polycom Vortex EF2280 Manuel utilisateur

Polycom

Polycom Vortex EF2201 Manuel utilisateur

Polycom

Polycom KIRK 5020 Manuel utilisateur

Polycom

Polycom VVX 410 Instructions d'installation et d'utilisation

Polycom

Polycom Vortex EF2201 Mode d’emploi

Polycom

Polycom OTX 300 Instructions de montage

Polycom

Polycom Vortex EF2201 Manuel utilisateur

Polycom

Polycom Vortex EF2280 Manuel utilisateur

Polycom

Polycom Vortex EF2241 Manuel utilisateur

Polycom

Polycom Vortex EF2241 Mode d'emploi

Polycom

Polycom Vortex EF2201 Manuel utilisateur

Polycom

Polycom SoundPoint IP Backlit Expansion Module Manuel utilisateur

Polycom

Polycom Vortex EF2210 Manuel utilisateur

Polycom

Polycom Vortex EF2211 Manuel utilisateur

Polycom

Polycom Vortex EF2201 Manuel d'installation

Polycom

Polycom Vortex EF2210 Guide de dépannage

Polycom

Polycom Vortex EF2241 Manuel utilisateur

Polycom

Polycom VVX EM 50 Manuel utilisateur

Polycom

Polycom Vortex EF2241 Instructions d'installation et d'utilisation

Polycom

Polycom Vortex EF2210 Manuel utilisateur

Polycom

Polycom Vortex EF2241 Instructions d'installation et d'utilisation

Polycom

Polycom Vortex EF2201 Manuel utilisateur

Polycom

Polycom KYRK 7010 Manuel utilisateur

Polycom

Polycom Vortex EF2201 Manuel utilisateur

Manuels Accessoires pour téléphone populaires d'autres marques

IAI

IAI CON-T Manuel utilisateur

BT DIVERSE 5400 Manuel utilisateur

Tadiran Telecom

Tadiran Telecom EMERALD ICE Manuel utilisateur

Musicam

Musicam FieldFone II Manuel utilisateur

TIPTEL

TIPTEL DECT Set 50 Manuel utilisateur

Panasonic

Panasonic KX-UDS124 Manuel utilisateur

BT BT7600 Fiche technique

Panasonic

Panasonic KX-TVP100E Manuel utilisateur

View

View VP-PC Manuel utilisateur

Baldwin Boxall

Baldwin Boxall BT8 Manuel utilisateur

SMC Networks

SMC Networks SMCDPCR-AP Manuel utilisateur

SkyLink

SkyLink SD-001 Manuel utilisateur

Nera

Nera ISDN Manuel utilisateur

MCheeta

MCheeta CT-CID803 Plus Manuel utilisateur

YASKAWA

YASKAWA YRC1000 Manuel utilisateur

Intellitouch

Intellitouch MOH-500E Manuel utilisateur

Viking

Viking SQRG-12 Instructions d'utilisation

Clarity

Clarity CE225 Manuel utilisateur