Planmeca X-RAY GENERATOR PCB Mode d’emploi

X-RAY GENERATOR PCB

REPLACEMENT INSTRUCTIONS

WARNING

Make sure that the power supply is switched off before starting Generator PCB

replacement.

1. Loosen the three attachment screws and remove the generator cover.

Complieswith

DHHSradiation

performance

standards

21CFR

SubchapterJ.

220V- 240 V AT

100V- 115 V 15 70kVmaximum 1800mAs/h

Totalfiltration:2,0 mm EquAl

WARNING:

Forcontinued protection

againstrisk of fire replace

onlywith same type and

ratingof fuse.

Manufacturedby:

PlanmecaOY

00880HELSINKI

FINLAND

LBL-Z-006D

1000VA50/60Hz

0537

I_7.eps

Generator cover

PLANMECA INTRA

Prostyle

INTRA

PROSTYLE INTRA

Generator cover

Publication number 10010526 version 1

X-RAY GENERATOR PCB

2/4 Installation instructions

2. Measure that the mains voltage is not present at the mains input terminals (P5) marked N and L.

3. Disconnect the connectors from terminals P1, P3, P5, P6 P7, P8, P9 and P10.

NOTE In Intra X-ray units manufactured after October 2000 the generator PCB is attached to the

frame with the two M3x6 DIN 912 screws located behind the generator assembly frame.

You have to lift the whole Generator PCB assembly from the wall adapter before you can

remove the PCB , see step 5 and step 6, number 1. With the older X-ray units you can pro-

ceed from step 6, number 2.

4. Loosen the four M4x8 ISO 7380 screws of the generator assembly frame (1). Lift the generator

assembly upwards (2). The generator assembly can now be lifted away from the wall adapter (3).

I_tech_3.eps

P8P10

I_tech_4_2.eps

3/4

Installation instructions

X-RAY GENERATOR PCB

5. (1) Lift the generator assembly away from the wall adapter and open the two M3x6 DIN 912 screws

located behind the generator assembly frame.

(2) Remove the eight M4 DIN 934 attachment nuts and ø4.3 DIN 6798 washers from the Generator

PCB (2).

(3) Unscrew the two M4x8 DIN 84 screws.

6. Remove the Generator PCB.

7. Install the new Generator PCB in reverse order. Note, that the new Generator PCB is not attached

to the frame with the two M3x6 DIN 912 screws located behind the generator assembly frame.

I_tech_4_3.eps

M4 DIN 934 nut

and M4 washer

X-RAY GENERATOR PCB

4/4 Installation instructions

Table des matières

Autres manuels Planmeca Équipement dentaire

Planmeca

Planmeca Compact i Classic Manuel utilisateur

Planmeca

Planmeca Planmeca ProMax 3D s Manuel utilisateur

Planmeca

Planmeca Proline XC Manuel utilisateur

Planmeca

Planmeca PlanMill 40 S Manuel utilisateur

Planmeca

Planmeca FIT CAD System Manuel utilisateur

Planmeca

Planmeca Sovereign Classic Manuel utilisateur

Planmeca

Planmeca Proline XC Panoramic Manuel d'utilisation et d'entretien

Planmeca

Planmeca Compact i5 Manuel utilisateur

Planmeca

Planmeca Chairside PlanScan Manuel utilisateur

Planmeca

Planmeca ProScanner Manuel utilisateur

Planmeca

Planmeca Sovereign Manuel utilisateur

Planmeca

Planmeca Creo C5 Manuel utilisateur

Planmeca

Planmeca Viso Manuel utilisateur

Planmeca

Planmeca Compact i Classic v2 Manuel utilisateur

Planmeca

Planmeca Chair Manuel utilisateur

Planmeca

Planmeca Compact i3 Manuel utilisateur

Planmeca

Planmeca ProScanner 2.0 Manuel utilisateur

Planmeca

Planmeca Compact i3 Manuel utilisateur

Manuels Équipement dentaire populaires d'autres marques

Vatech

Vatech EzRay Air VEX-P300 Manuel utilisateur

KaVo

KaVo GENTLEpower LUX Contra-angle 25 LP Manuel utilisateur

DENTSPLY

DENTSPLY SmartLite Focus Manuel utilisateur

LM ProPower CombiLED Manuel utilisateur

Owandy Radiology

Owandy Radiology RX-AC Manuel utilisateur

mectron

mectron Piezosurgery Manuel utilisateur

Belmont

Belmont CREDIA G1 Manuel utilisateur

Bego

Bego Fornax T Manuel utilisateur

Renfert

Renfert SYMPRO Guide rapide

Ateco

Ateco AT-301 Manuel utilisateur

Nevadent

Nevadent NZPS 3 A1 Manuel utilisateur

Muss Dental

Muss Dental MA 50 Manuel technique

Diplomat

Diplomat Comfort Series Manuel utilisateur

Dentatus

Dentatus Nyström Manuel utilisateur

OMS

OMS DUKE EASY Manuel

OMS

OMS LINEA PATAVIUM Manuel

BRYANT DENTAL

BRYANT DENTAL Ignis Gesture A-494322 Manuel utilisateur

Dekema

Dekema AUSTROMAT 664 iSiC Manuel utilisateur