Planet WAP-4060PE Manuel utilisateur

Table of Contents

Physical Details 1

Front panel 1

Rear panel 2

Hardware Installation 2

General installation 2

PoE installation 3

Configuring the Access Point 3

WAP-4060PE Manager Installation 3

Running WAP-4060PE Manager 4

Further Configuration 5

EMQ-WAP4060.indd 2005/1/10, �� 11:321

This page is intentionally left blank

EMQ-WAP4060.indd 2005/1/10, �� 11:322

Package Content

• WAP-4060PE

• Dipole Antenna

• Quick Installation Guide

• User’s manual CD-ROM

• Power Adapter

 NOTE:

If any of the above items are missing or damaged, contact

your local dealer for support.

Physical Details

Front panel

STATUS On - Error condition.

Off - Normal operation.

Blinking - During start up, and when the Firmware is being up-

graded.

POWER On - Normal operation.

Off - No power

LAN On - The LAN (Ethernet) port is active.

Off - No active connection on the LAN (Ethernet) port.

Flashing - Data is being transmitted or received via the corre-

sponding LAN (Ethernet) port.

WLAN On - Idle

Off - Error- Wireless connection is not available.

Flashing - Data is being transmitted or received via the Wire-

less access point. Data includes "network traffic" as well as user

data.

EMQ-WAP4060.indd 2005/1/10, �� 11:321

Rear panel

ANT One dipole antenna is supplied. Best results are usually ob-

tained with the antenna in a vertical position.

CONSOLE DB9 female RS232 port.

RESET Button This button has two (2) functions:

Reboot. When pressed and released, the WAP-4060PE will

reboot (restart).

Reset to Factory Defaults. This button can also be used to

clear ALL data and restore ALL settings to the factory default

values.

To Clear All Data and restore the factory default values:

1. Power Off the WAP-4060PE.

2. Hold the Reset Button down while you Power On the

device.

3. Continue holding the Reset Button until the Status (Red)

LED blinks TWICE.

4. Release the Reset Button.

The factory default configuration has now been restored,

and the WAP-4060PE is ready for use.

LAN (PoE) Use a standard LAN cable (RJ45 connectors) to connect this

port to a 10BaseT or 100BaseT hub on your LAN.

Power port Connect the supplied power adapter here.

Hardware Installation

General installation

1. Locate an optimum location for the WAP-4060PE. The best place for your

WAP-4060PE is usually at the center of your wireless network, with line of sight

to all of your mobile stations.

2. Assemble the antennas to WAP-4060PE. Try to place them to a position

that can best cover your wireless network. The antenna’s position will enhance

the receiving sensitivity.

EMQ-WAP4060.indd 2005/1/10, �� 11:322

3. Connect RJ-45 cable to WAP-4060PE. Connect this WAP-4060PE to your

LAN switch/hub or a single PC.

4. Plug in power adapter and connect to power source. After power on,

WAP-4060PE will start to operate.

 NOTE:

ONLY use the power adapter supplied with the WAP-4060PE.

Otherwise, the product may be damaged.

PoE installation

1. Do not connect the supplied power adapter to the WAP-4060PE.

2. Connect one end of a standard (category 5) LAN cable to the Ethernet port on

the WAP-4060PE.

3. Connect the other end of the LAN cable to the powered Ethernet port on a suit-

able PoE Adapter or switch. (IEEE 802.3af compliant)

4. Connect the unpowered Ethernet port on the PoE adapter to your Hub or

switch.

5. Connect the power supply to the PoE adapter and power up.

6. Check the LEDs on the WAP-4060PE to see it is drawing power via the Ethernet

connection.

Conguring the Access Point

A simple Windows setup utility is supplied on the CD-ROM. This utility can be used to

assign a suitable IP address to the WAP-4060PE. Using this utility is recommended,

because it can locate the WAP-4060PE even if it has an invalid IP address.

WAP-4060PE Manager Installation

1. Insert the User’s Manual and Utility CD into the CD-ROM drive.

2. Once the menu screen appears, click on the “WAP-4060PE Manager” hyperlink

for installation. If the menu screen does not appear, you can click the Start but-

ton and choose Run. When the dialog box appears, enter E:\Utility\setup.exe

(Assume “E” is your CD-ROM drive). Follow the prompts to complete the instal-

lation.

3. After the installation completes, you can start this utility from “Start”>”Program

Files”>”Planet”>”WAP-4060PE Manager”.

EMQ-WAP4060.indd 2005/1/10, �� 11:323

Running WAP-4060PE Manager

When the utility is executed, it searches the network for all active WAP-4060PE, and lists

them on screen, as shown by the example below.

Wireless Access Points

The main panel displays a list of all Wireless Access Points found on the network. For each

Access Point, the following data is shown:

Name The device name of the WAP-4060PE.

IP address The IP address for the WAP-4060PE.

MAC Address The hardware or physical address of the WAP-4060PE.

IEEE Standard The wireless standard or standards used by the WAP-4060PE

(e.g. 802.11b, 802.11g)

FW Version The current Firmware version installed in the WAP-4060PE.

Description Any extra information for the WAP-4060PE, entered by the

administrator.

 NOTE:

If the desired device is not listed, check that the device is

installed and powered on, then update the list by clicking the

Refresh button.

Buttons

Refresh Click this button to update the Wireless Access Point device

listing after changing the name or IP Address.

Detail Info When clicked, additional information about the selected device

will be displayed.

Web

Management

Use this button to connect to the WAP-4060PE’s Web-based

management interface.

EMQ-WAP4060.indd 2005/1/10, �� 11:324

Set IP Address Click this button if you want to change the IP Address of the

Wireless Access Point.

Exit Exit the Management utility program by clicking this button.

Setup Procedure

1. Select the desired Wireless Access Point from the list.

2. Click the Set IP Address button.

3. If prompted, enter the user name and password. The default values are admin

for the User Name, and password for the Password.

4. Ensure the IP address, Network Mask, and Gateway settings are correct for

your LAN. Save any changes.

The initial IP address setup is now completed. You can click on the Web Management

button to access the web interface of WAP-4060PE for more congurations.

Further Conguration

If you want to congure more settings of WAP-4060PE, please refer to the user s manual

in the CD. If you have any difculty on resolving the problem while installing or using the

WAP-4060PE, please feel free to contact your local dealer or PLANET Technical Support.

EMQ-WAP4060.indd 2005/1/10, �� 11:325

This page is intentionally left blank

EMQ-WAP4060.indd 2005/1/10, �� 11:326

Autres manuels pour WAP-4060PE

Table des matières

Autres manuels Planet Point d'accès sans fil

Planet

Planet WDAP-C7200AC Manuel utilisateur

Planet

Planet WAPC-1232HP Manuel utilisateur

Planet

Planet WDAP-W1200E Manuel utilisateur

Planet

Planet WDAP-1750AC Manuel utilisateur

Planet

Planet IAP-2000PS Manuel utilisateur

Planet

Planet WAP-4000A Manuel utilisateur

Planet

Planet WDAP-802AC Manuel utilisateur

Planet

Planet WDAP-702AC Manuel utilisateur

Planet

Planet WAP-4033 Manuel utilisateur

Planet

Planet WAP-1000 WireFree Manuel utilisateur

Planet

Planet WNAP-1110 Manuel utilisateur

Planet

Planet WAP-252N Manuel utilisateur

Planet

Planet WAP-3000 Manuel utilisateur

Planet

Planet WDAP-2000PE Manuel utilisateur

Planet

Planet WAP-4060PE Manuel utilisateur

Planet

Planet WNAP-6350 Manuel utilisateur

Planet

Planet IAP-2000PS Manuel utilisateur

Planet

Planet WNAP-3000PE Manuel utilisateur

Planet

Planet WDAP-C7200AC Manuel utilisateur

Planet

Planet WNAP-7320 Manuel utilisateur

Planet

Planet WNAP-6306 Manuel utilisateur

Planet

Planet WNAP-7350 Manuel utilisateur

Planet

Planet WDAP-C1800AX Manuel utilisateur

Planet

Planet WBS-502AC Manuel utilisateur

Manuels Point d'accès sans fil populaires d'autres marques

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manuel utilisateur

Ubiquiti

Ubiquiti NanoStation NSM2 Manuel utilisateur

Cisco

Cisco Aironet 1550 Series Manuel utilisateur

Aruba

Aruba IAP-335 Manuel utilisateur

Advantek Networks

Advantek Networks AWN-AP-54MR Manuel utilisateur

IP-COM

IP-COM AP355 Manuel utilisateur

Buffalo

Buffalo AirStation WLA-L11G Manuel utilisateur

EnGenius

EnGenius EnStationACv2 Manuel utilisateur

D-Link

D-Link DAP-3662 Manuel utilisateur

xG Technology

xG Technology xMax CN1300 Manuel utilisateur

Widelink

Widelink ezWave WAP-1100 Series Manuel utilisateur

Edimax

Edimax CAP1200 Manuel utilisateur

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manuel utilisateur

Aruba

Aruba AP-203R Manuel utilisateur

LuXout Shades

LuXout Shades LUXSHADE MOTION Manuel utilisateur

CreatComm

CreatComm TB5F Manuel utilisateur

SineDigital

SineDigital MW-1500AP(H) Manuel utilisateur

TP-Link

TP-Link AP9650 V1 Manuel utilisateur