Planet HDP-5240PT Manuel utilisateur
720p SIP Multi-unit Video Door Phone with RFID
and PoE
HDP-5240PT
Quick Installation Guide
Table of Contents
1. Package Contents.............................................................................3
2. PhysicalSpecications ......................................................................4
2.1 Front Panel ...............................................................................4
2.2 I/O Control Description ..............................................................6
3. Installation ....................................................................................10
4. Searching Door Phone IP Address....................................................15
5. SIP Door Phone Setting ..................................................................16
6. Door Unlocking Setting...................................................................18
7. Customer Support..........................................................................22
3
1. Package Contents
Thank you for choosing PLANET HDP-5240PT. Before installing the door
phone, please verify the contents inside the package box.
The package should contain the following items:
The Multi-unit Door Phone Quick Installation Guide
Screw Kit RFID Card x 3
4
2.PhysicalSpecications
Dimensions (W x D x H) 160 x 93 x 35 mm
Weight 330g (gross weight)
2.1 Front Panel
Lock Status
Call and Ring Status
Network and Registration Status
Camera
MIC
RFID Reader
Numeric Keypad
(password or dialing)
DSS Key with LED
Speaker
Interface Description
Camera The door phone has a built-in IP camera supporting a
high-resolution video of up to 1280 x 720 pixels.
Mic The door phone has a built-in microphone hidden in the
pinhole located on the front panel.
Speaker The door phone has a built-in speaker for convenient
communication and alert use.
RFID Reader Use RFID cards to unlock the door by touching RFID
reader of device.
5
Button Denition
Button Description
Programmable Keys It can be set with a variety of functions in order
to meet the needs of different occasions
Numeric Keyboard Input password to open the door or calls.
LED Denition
LED Status Description
Lock
Steady Blue Door unlocking
Off Door locking
Call & Ring
Blinks per second Call Hold or Ringing
Off On Hook
Blinks every 3 seconds Device in the issuing state
Steady Blue Online talking
Network & SIP
Registration
Blinks per second Network error
Off Network is normal, SIP is
not registered
Blinks every 3 seconds SIP Registration failed
Steady Blue SIP Registration succeeded
6
2.2 I/O Control Description
After removing the front panel of HDP-5240PT, there are two terminal
block connectors for power connection and digital I/O connections as
shown in the picture below.
JP1 Jumper
Network port
Power and lock
connector
Power Connector
The HDP-5240PT requires either IEEE 802.3af/at PoE or DC power from
the power connector.
It shows the two-pin connector comes with a power source of 12V DC, 1A
(max.).
Network Connector
7
Power and Electric-lock Connector
1 234567
+DC 12V VSS NC COM NO S-IN S-OUT
12V DC Input Electric-lock switch Indoor switch
JP1 Jumper
There are two modes for power supply of electric-lock as shown in the
picture below. (The default is “Active Mode”).
Passive Mode: When the electric-lock starting current is more than
12V/1000mA, the external drive mode, the electric lock
interface for short circuit output control, is used.
Active Mode: When the electric-lock starting current is less than
12V/1000mA, the electric lock interface is 12V DC output
in the internal drive mode is used.
Wiring instructions
NO: Normally Open Contact
COM: Common Contact
NC: Normally Close Contact
8
Driving Mode Electric-lock Mode
JP1
Jumper
Active
Connections
Graphs
Active Passive
No
electricity
when open
Electrify
when
open
√ √
Please refer to
the Graph 1 in
the next page
√ √
Please refer to
the Graph 2 in
the next page
√ √
Please refer to
the Graph 3 in
the next page
√ √
Please refer to
the Graph 4 in
the next page
√ √
Please refer to
the Graph 5 in
the next page
9
Graph 1 Graph 2
Graph 3 Graph 4
Graph 5
10
3. Installation
The HDP-5240PT is constructed of four parts as shown below. Prior
to the installation, the installer is required to remove the front panel of
the HDP-5240PT for wall mounting. Please follow the steps below for the
installation.
Figure 1 Three Major Parts of HDP-5240PT
Step 1: Installation preparation
A. Check the following contents:
Hex wrench x 1
RJ45 plugs x 2 (1 spare)
KA4 x 25mm screws x 4
25mm screw anchors x 4
B. Tools that may be required:
Hex wrench
Phillips screwdriver (Ph2 or Ph3), hammer, RJ45 crimper
Electric impact drill with an 6mm drill bit.
Autres manuels pour HDP-5240PT
1
Table des matières
Autres manuels Planet Système d'interphone
Planet
Planet HDP-1160PT Manuel utilisateur
Planet
Planet HDP-1100PT Manuel utilisateur
Planet
Planet HDP-1100PT Manuel utilisateur
Planet
Planet HDP-1260PT Manuel utilisateur
Planet
Planet HDP-5240PT Manuel utilisateur
Planet
Planet HDP-1261PT Manuel utilisateur
Planet
Planet HDP-1160PT Manuel utilisateur
Planet
Planet VTS-700WP Manuel utilisateur
