Planet Networking & Communication WNAP-C3220 Manuel utilisateur

Note

– 1 – – 2 –

– 3 – – 4 –

1. Package Contents

2. Physical Introduction

3. Hardware Installation

– 7 – – 8 –

4. Wired Network Configuration (Windows 7)

6. Wireless Network Connection

5. Enter into the Web Management

– 5 – – 6 –

Front Panel Description

Rear Panel Description

Wireless AP Quick Guide CD-ROM

Power Adapter Mounting KitEthernet Cable

You have already finished the configuration of the

WNAP-C3220. Now you can use your iPhone, iPad, laptop,

and any other Wi-Fi device to connect with it wirelessly and

start surfing the internet.

2011-E10400-002

Thank you for choosing PLANET WNAP-C3220. Before installing

the AP, please verify the contents inside the package box.

If there is any item missing or damaged, please

contact the seller immediately.

Step 1: Attach the bracket to the wall or ceiling, and mark

each point in the bracket for the screws. Remove

the bracket to drill the points and insert the plastic

wall-mounts. Use screws to lock the bracket by a

screw driver.

Step 3: Plug the power adapter into the WNAP-C3220.

If WNAP-C3220 is connected to an 802.3af PoE

switch in STEP 2, you don’t have to plug the power

adapter.

Step 4: Attach the WNAP-C3220

to the mounting

bracket.

Step 5: Installation is

successfully

completed.

Step 2: Plug the RJ-45 Ethernet cable into the WNAP-C3220.

Step 4: Once the basic configuration of the WNAP-C3220 is

done, click “Save” button to make the change take

effect.

Step 3: After you enter into the Web User Interface, go to

WLAN Settings to configure your wireless

network.

For security reasons, strongly recommended to

configure the Encryption Method and Passphrase of

your wireless network.

1. Click “Start” button located at the lower-left corner of

your computer.

2. Click “Control Panel”.

3. Double click “Network and Sharing Center” icon.

4. Click “Change Adapter Settings”.

5. Double click “Local Area Connection”.

6. Select “Internet Protocol Version 4(TCP/IPv4)” and

click “Properties”.

7. Select “Use the following IP address”, and then click

“OK” button twice to save the configuration. For

example, as the default IP address of the WNAP-C3220 is

192.168.1.253 and the router is 192.168.1.254, you may

choose from 192.168.1.1 to 192.168.1.252.

Default IP Address: 192.168.1.253

Default Username: admin

Default Password: admin

Default SSID: WNAP-C3220

Default Wireless Encryption Type: None

A computer with wired Ethernet connection is required for the

first-time configuration of the WNAP-C3220.

Note

1. ONLY use the power adapter supplied with

WNAP-C3220. Otherwise, the product may be

damaged.

2. For the power supply of WNAP-C3220, you could

use either IEEE 802.3af PSE device or 12V DC

adapter. Please do not use 12V adapter and PSE

device at the same time. It may damage the

WNAP-C3220 itself.

Step 2: Highlight the wireless network (SSID) to connect

and click [Connect] button.

x 4 x 4

1 x 10/100/1000Mbps PoE LAN Port

Reset Button

Power Connector 12V DC Input

Step 1: Right-click on the network icon displayed in the

system tray.

Power LED

WNAP-C3220

Quick Installation Guide

802.11n Ceiling Mount Wireless

Range Extender / Access Point

Step 1: The Web management allows you to access and

manage the WNAP-C3220 easily. Launch the Web

browser and enter the default IP address

http://192.168.1.253

Step 2: When the login window pops up, please enter the

User Name and Password. The default User Name

and Password are both “admin”. Then click OK

button to continue.

For security reasons it is recommended to change the

password at the first login and memorize it.

Step 3: Enter the encryption key of the WNAP-C3220 if

necessary.

FURTHER INFORMATION

The above steps introduce simple installations and

configurations for the WNAP-C3220. For further configurations

of LAN, Wireless, Access Control, etc, please refer to the user’s

manual in the CD. If you have further questions, please

contact the local dealer or distributor where you purchased this

product.

Note

– 1 – – 2 –

– 3 – – 4 –

1. Package Contents

2. Physical Introduction

3. Hardware Installation

– 7 – – 8 –

4. Wired Network Configuration (Windows 7)

6. Wireless Network Connection

5. Enter into the Web Management

– 5 – – 6 –

Front Panel Description

Rear Panel Description

Wireless AP Quick Guide CD-ROM

Power Adapter Mounting KitEthernet Cable

You have already finished the configuration of the

WNAP-C3220. Now you can use your iPhone, iPad, laptop,

and any other Wi-Fi device to connect with it wirelessly and

start surfing the internet.

2011-E10400-002

Thank you for choosing PLANET WNAP-C3220. Before installing

the AP, please verify the contents inside the package box.

If there is any item missing or damaged, please

contact the seller immediately.

Step 1: Attach the bracket to the wall or ceiling, and mark

each point in the bracket for the screws. Remove

the bracket to drill the points and insert the plastic

wall-mounts. Use screws to lock the bracket by a

screw driver.

Step 3: Plug the power adapter into the WNAP-C3220.

If WNAP-C3220 is connected to an 802.3af PoE

switch in STEP 2, you don’t have to plug the power

adapter.

Step 4: Attach the WNAP-C3220

to the mounting

bracket.

Step 5: Installation is

successfully

completed.

Step 2: Plug the RJ-45 Ethernet cable into the WNAP-C3220.

Step 4: Once the basic configuration of the WNAP-C3220 is

done, click “Save” button to make the change take

effect.

Step 3: After you enter into the Web User Interface, go to

WLAN Settings to configure your wireless

network.

For security reasons, strongly recommended to

configure the Encryption Method and Passphrase of

your wireless network.

1. Click “Start” button located at the lower-left corner of

your computer.

2. Click “Control Panel”.

3. Double click “Network and Sharing Center” icon.

4. Click “Change Adapter Settings”.

5. Double click “Local Area Connection”.

6. Select “Internet Protocol Version 4(TCP/IPv4)” and

click “Properties”.

7. Select “Use the following IP address”, and then click

“OK” button twice to save the configuration. For

example, as the default IP address of the WNAP-C3220 is

192.168.1.253 and the router is 192.168.1.254, you may

choose from 192.168.1.1 to 192.168.1.252.

Default IP Address: 192.168.1.253

Default Username: admin

Default Password: admin

Default SSID: WNAP-C3220

Default Wireless Encryption Type: None

A computer with wired Ethernet connection is required for the

first-time configuration of the WNAP-C3220.

Note

1. ONLY use the power adapter supplied with

WNAP-C3220. Otherwise, the product may be

damaged.

2. For the power supply of WNAP-C3220, you could

use either IEEE 802.3af PSE device or 12V DC

adapter. Please do not use 12V adapter and PSE

device at the same time. It may damage the

WNAP-C3220 itself.

Step 2: Highlight the wireless network (SSID) to connect

and click [Connect] button.

x 4 x 4

1 x 10/100/1000Mbps PoE LAN Port

Reset Button

Power Connector 12V DC Input

Step 1: Right-click on the network icon displayed in the

system tray.

Power LED

WNAP-C3220

Quick Installation Guide

802.11n Ceiling Mount Wireless

Range Extender / Access Point

Step 1: The Web management allows you to access and

manage the WNAP-C3220 easily. Launch the Web

browser and enter the default IP address

http://192.168.1.253

Step 2: When the login window pops up, please enter the

User Name and Password. The default User Name

and Password are both “admin”. Then click OK

button to continue.

For security reasons it is recommended to change the

password at the first login and memorize it.

Step 3: Enter the encryption key of the WNAP-C3220 if

necessary.

FURTHER INFORMATION

The above steps introduce simple installations and

configurations for the WNAP-C3220. For further configurations

of LAN, Wireless, Access Control, etc, please refer to the user’s

manual in the CD. If you have further questions, please

contact the local dealer or distributor where you purchased this

product.

Table des matières

Autres manuels Planet Networking & Communication Point d'accès sans fil