Pizzacraft 6000 series Manuel utilisateur
NATURAL
GAS KIT Makes great tasting,
traditional Italian pizza –
with bubbly cheese,
crispy
crust & toasty toppings.
6000 series outdoor pizza ovens
OWNER’S MANUAL
Pizzeria Pronto®
PizzaQue®
Pizzacraft®
PC6018
CS1214
©The Companion Group 2014
1250 9th Street, Berkeley, CA 94710
800-521-0505
IMPORTANT: This instruction manual contains important information necessary for the proper
assembly and safe use of the appliance.
Read and follow all warnings and instructions carefully before assembling and using the appliance.
Keep this manual for future reference.
TABLE OF CONTENTS
Safety Information......................................3
Assembly Instructions ...............................5
Operation Instructions..............................13
Troubleshooting.........................................14
Warranty and Registration........................15
3
A. IMPORTANT: Before you begin...
1. Read and follow all instructions carefully.
2. WARNING: Connection to gas source must be
done by a certied plumber.
3. Installation must be made in accordance with any
local codes or regulations, or in the absence of
local codes of regulations, in accordance with the
National Fuel Gas Code (NFPA 54/ANSI Z223.1).
4. This device is only intended for use outdoors with
portable appliances that may be moved for conve-
nience of operation.
5. Thehoseandttingsaredesignedformovement
after installation, but must not be kinked, twisted
or torqued.
6. Thehoseandttingsshouldbevisuallyinspected
periodically to determine that they have not been
damaged, and are suitable for continued use.
7. Protectthehoseandttingsfromdust,dirtand
damage when not in use. Insert the plastic plug
in the socket and the cap over the hose end plug
whenever the hose is removed from the socket.
8. Perform “leak test” by following “Leak Test In-
structions” on pg.12.
9. Only use the Quick Connect Socket with the pro-
vided hose end plug.
SAFETY INFORMATION
B. SPECIAL NOTES:
- This device requires outlet pressure of 7 inches of
water column.
If pressure is greater than 1/2 psi, make sure that
an inline regulator is present.
Prior to 1998, all residual gas service regulators
were set with an outlet pressure of 7 inches of
water column.
In the 1998 edition of NFPA 54, the National Fuel
Gas Code, a change was made allowing service
regulators of 2 and 5 psi.
With this change it was also required that an
inline regulator be connected between the service
regulator and the applience regulator if the 2 or 5
psi system is used. This additional regulator is not
supplied with the product.
It is possible for a consumer, making the connec-
tion themselves, or a plumber, not checking, to
tap into a 2 or 5 psi line. If a pressure of 2 psi or
greater is supplied to the appliance regulator on
certain appliances it will shut down and not de-
liver any gas to the appliance. Additional concerns
are raised by the fact that both the quick connect
socket and the gas hose are only rated to 1/2 psi.
If the quick disconnect socket, hose and oven are
properly connected and still not getting gas, deliv-
erypressureneedstobeveried.
4
DANGER
DANGER
If you smell gas:
1. Shut off gas to the appliance.
2. Extinguish any open ame.
3. Remove hood.
4. If odor continues, keep away from the appliance and immediately call
your re department.
1. Never operate this appliance unattended.
2. For outdoor use only.
3. Never operate this appliance within 48 inches (122 cm) of any structure,
combustible material or other gas cylinder.
4. Never operate this appliance within 25 ft. (7.5 m) of any ammable liquid.
5. If a re should occur, keep away from the appliance and immediately
call your re department. Do not attempt to extinguish an oil or grease
re with water.
Failure to follow these instructions could result in fire or explosion,
which could cause property damage, personal injury or death.
Failure to follow these instructions could result in fire or explosion,
which could cause property damage, personal injury or death.
CALIFORNIA PROPOSITION 65 WARNING:
The burning of gas cooking fuel generates some by-products, which are on the list of substances
known by the State of California to cause cancer, reproductive harm or other birth defects. This
product may contain chemicals known to the state of California to cause cancer, reproductive
harm or birth defects. To reduce exposure to these substances, always operate this unit according
to the use and care manual, ensuring you provide good ventilation when cooking with gas.
5
ASSEMBLY INSTRUCTIONS
Before beginning assembly of product, make sure all parts are present. Compare parts with package
contents and hardware contents list. Do not discard packing materials before assembly is complete.
If any part is missing or damaged, do not attempt to assemble the product. Call customer service at 800-
521-0505.
Estimated assembly time: 30 minutes
Tools required - #2 Phillips screw driver not included; all other required tools included
PACKAGE CONTENTS:
1. 6’ natural gas hose
2. Jet valve
3. Knob
4. Quick disconnect socket
5. Jet and hose combo
wrench
1.
2.
3.
4.
5.
6
1. Shut o gas supply and remove cap from the outlet of the housing pipe.
WARNING: Connection to gas source must be done by a certied plumber.
2. RECOMMENDATION: If not already equipped, intall a shut-off valve on the gas supply side before
installing the Quick Connect Socket.
Wall hole where housing
pipe extends from
Wall hole where housing
pipe extends from
Existing gas
valve cap
* CONFIRM GAS LINE PRESSURE IS 7”
W.C.
7
4. Disconnect the existing Gas Hose from appliance by unscrewing the 3/8 SAE FLARE FEMALE end of the
hose from the 3/8 SAE FLARE MALE appliance inlet using the hose wrench provided.
Propane Tank Gas
Hose with regulator
Quick Disconnect
Socket
Shut-off valve
Existing outlet of the
house piping
3. Coat the 3/8 NPT MALE outlet of the house piping with gas resistant pipe dope. Attach the threaded end
ofthequickdisconnectsocket(note:thedirectionarrowofowisindicatedonthesocket)tothethread-
ed outlet of the house piping and tighten with hose wrench.
Wall hole where housing
pipe extends from
8
6. Remove the inlet pipe from the oven body by unscrewing the 2 screws on front of oven beneath the knob
as well as the screw securing the inlet pipe mount underneath the oven. Disconnect the pipe inlet from the
starter connection and remove.
5. Remove hood and pizza stones from oven and carefully set them aside. Flip oven base upside down to
access the inlet pipe.
Inlet Pipe
9
8. Replace the old Jet with the new one provided in the NG Conversion Kit.
7. Uncrew the Jet from the interior end of the inlet pipe facing in toward the oven.
Propane Gas Jet - old Jet has
smaller internal hole
Jet
Natural Gas Jet - new
Jet has larger internal hole
10
10.Carefullyipovenrightsideupandreassemblehoodandpizzastones.
9. Replace inlet pipe. Insert gas inlet assembly into body as shown. Secure control valve with 2 supplied
screws to body front then secure pipe support with the third M4x5 Phillips screw. Attach control knob
by aligning the keyway and pushing onto valve spindle. Connect starter wire from valve assembly
to starter plug by rmly pushing it into place. TEST and CONFIRM that starter is providing an
interior spark.
*Flip over to TEST and CONFIRM that starter is providing an inte-
rior spark to Venturi tube. Interior
Spark
Autres manuels pour 6000 series
1
Table des matières
Autres manuels Pizzacraft Appareils de cuisine
