Pixel UTVANT Manuel utilisateur
Congratulaons on the purchase of a new SiriusXM Radio UTV antenna. Here
are instrucons on how to install this kit into a UTV. This kit is designed to be
installed on any UTV by using the supplied pipe mounng parts or ush/roof
mounng parts. It is recommended to select a locaon on your UTV that will
allow the antenna to have maximum clearance from a roof or other objects.
The following instrucons show an installaon on a pipe and roof allowing for
maximum clearance.
Installaon Instrucons
SiriusXM Radio UTV Antenna
Model # UTVANT
Pixel Technologies, Inc. | 800.595.0845 | www.pixelsatradio.com | [email protected] | Page 1
Package Includes:
(1) SiriusXM UTV Antenna
(1) Rubber Clamp
(1) L Bracket
(1) Tube of Locte
(1) Mounng Screw
(1) Locking nut
(4) Rubber washers
(1) Rubber cap
Antenna Installaon Tips
• Install the antenna element with the best line-of-sight for opmal performance
• Placing the antenna higher on the vehicle is recommended but not mandatory
• When riding in the northern most parts of the US and Canada, slanng the element southbound a
few degrees will increase the signal strength.
• Try not to stress the molded connector on the end of the antenna wire
• Keep the antenna away from heat and electrical sources
Antenna Base Assembly
1. Select the locaon to install your antenna allowing for maximum clearance.
2. Use the hardware shown in diagram A for this assembly type.
3. Insert the screw and lock washer into the base of the antenna as shown in diagram B.
4. Next install the L bracket and thread the screw through the square nut securing the L bracket as
shown in diagram C.
5. Be sure to ghten the L bracket securely in place.
Diagram A Diagram B Diagram C
Antenna Wire Installaon
1. Run the antenna cable from the antenna either inside the roll cage pipe tubing or along the outside
securing the antenna cable with cable es (not supplied). Be sure not to over ghten the cable es
as the stress could cause damage to the antenna wire.
2. Bring the antenna connecon to the desired locaon to install the gooseneck mount and protec-
ve case. It is recommended to leave about 12 inches of play in the cable at the point of installing
the gooseneck mount and case.
SiriusXM Radio UTV Antenna
Model # UTVANT
Flush / Roof Mount Assembly
1. Select the locaon to install your antenna allowing for maximum clearance.
2. Use the hardware shown in diagram A for this assembly type.
3. Drill a hole in the surface area of the desired mounng area.
4. Place the L bracket over the hole and secure the L bracket to the roof with the supplied mounng
screw, rubber, washer and lock nut as shown in Diagram D.
5. Be sure to place the rubber cap on the end of the screw.
Pipe Mount Antenna Assembly
1. Select the locaon on the roll cage to install your antenna allowing for maximum clearance.
2. Use the hardware shown in Diagram A for this assembly type.
3. Insert the screw shown in Diagram B into one of the rubber washers and slide it through the hole
on the L bracket. Next slide the second rubber washer onto the screw.
4. Insert the screw through the L bracket and then slide the second rubber washer over the screw.
This will help to reduce vibraon.
5. Slide the screw through the hole on the other end of the clamp as shown in Diagram C.
6. Screw the lock nut on the screw and ghten the screw securely.
7. Apply the supplied locking soluon to the screw and nuts as needed to secure the nut to the screw.
8. Be sure to place the rubber cap on the end of the screw.
Diagram B
Pixel Technologies, Inc. | 800.595.0845 | www.pixelsatradio.com | [email protected] | Page 2
Diagram A Diagram C Installed
Installed
Installaon Instrucons
Diagram A
Table des matières
Autres manuels Pixel Antenne radio
