Pittway System Sensor RTS451KEY Manuel utilisateur
D440-03-00 1 I56-758-05
RTS451KEY(A) Remote Test Station
INSTALLATION AND MAINTENANCE INSTRUCTIONS
A Division of Pittway
3825 Ohio Avenue, St. Charles, Illinois 60174
1-800-SENSOR2, FAX: 630-377-6495
NOTICE: This manual should be left with the owner/user
of this equipment.
General Information
The System Sensor RTS451KEY(A) is an automatic fire de-
tector accessory designed to test remotely located duct and
beam detectors. For 4-wire detectors, the RTS451KEY fea-
tures a multi-colored LED that alternates between steady
green and red. Green indicates power and that the detector
head is in place. Red indicates alarm. For 2-wire detectors,
the LED will show red for alarm. Consult the detector in-
stallation instructions for additional information.
The National Fire Protection Association has published
codes, standards, and recommended practices for the in-
stallation and use of this product. It is recommended that
the installer be familiar with these requirements, with local
codes, and any special requirements of the local authority
having jurisdiction.
RTS451 Contents
1 RTS451KEY(A) remote test station
1 #4 screw for mounting bracket
1 test coil*
1 screw pack (2 mounting screws)
2 Keys
1 jumper with spade lugs*
1 test coil mounting bracket*
*Not used with Model 6424 Projected Beam Smoke
Detector
ALARM
ON
RESET TEST
A78-2591-00
Figure 1. RTS451KEY:
Specifications
Dimensions: 4.6” H x 2.75” W x 1.8” D
Weight: 0.22 Lbs.
Power Requirements
Power LED (Green): 14 – 35 VDC, 12 mA maximum
Alarm LED (Red): 2.8 – 32 VDC, 10 mA maximum
Test Coil*: 15.5 – 32 VDC, 95 mA maximum
Total Current: 105 mA maximum
Alarm Response Time: 40 seconds maximum
Temperature: –10°C to 60°C (14°F to 140°F)
Humidity: 95% relative humidity, noncondensing
Operation
Test Function
Insert the key and turn clockwise to the “TEST” position.
Alarm Indication
With the key in the “TEST” position, some time will elapse
(40 seconds maximum) depending on the detector type, be-
fore the alarm indicating LED will turn red.
Reset Function
Turn the key counterclockwise to the “RESET” position and
hold. The LED should turn off. Then, turn the key back to
the “NORMAL” position and remove. The RTS451KEY is
capable of resetting only certain models of detectors. Refer
to the detector installation instructions for additional
information.
D440-03-00 2 I56-758-05
© System Sensor 1997
Three-Year Limited Warranty
System Sensor warrants its enclosed remote test station to be free from de-
fects in materials and workmanship under normal use and service for a
period of three years from date of manufacture. System Sensor makes no
other express warranty for this remote test station. No agent, representa-
tive, dealer, or employee of the Company has the authority to increase or
alter the obligations or limitations of this Warranty. The Company’s obli-
gation of this Warranty shall be limited to the repair or replacement of any
part of the remote test station which is found to be defective in materials
or workmanship under normal use and service during the three year pe-
riod commencing with the date of manufacture. After phoning System
Sensor’s toll free number 800-SENSOR2 (736-7672) for a Return Authori-
zation number, send defective units postage prepaid to: System Sensor,
Repair Department, RA #__________, 3825 Ohio Avenue, St. Charles, IL
60174. Please include a note describing the malfunction and suspected
cause of failure. The Company shall not be obligated to repair or replace
units which are found to be defective because of damage, unreasonable
use, modifications, or alterations occurring after the date of manufacture.
In no case shall the Company be liable for any consequential or incidental
damages for breach of this or any other Warranty, expressed or implied
whatsoever, even if the loss or damage is caused by the Company’s negli-
gence or fault. Some states do not allow the exclusion or limitation of inci-
dental or consequential damages, so the above limitation or exclusion may
not apply to you. This Warranty gives you specific legal rights, and you
may also have other rights which vary from state to state.
24 VDC
AUX POWER
SUPPLIED
BY USER
(100mA
SUPPLY)
DH400
DUCT DETECTOR 24 VAC (+10%, –15%)
FULL WAVE RECTIFIED,
UNFILTERED POWER
MAY BE USED
RTS451KEY
REMOTE TEST STATION
METHOD #1 — AUX POWER LOCATED AT DUCT DETECTOR
TEST
1
2
4
5
(+)
(–) (+)
(–) 3
4
6
7
8
2.8 VDC
IN ALARM
(–)
(+)
24 VDC
AUX POWER
SUPPLIED
BY USER
(100mA
SUPPLY) TEST
1
2
4
5
(+)
(–)
(+)
(–)
3
4
6
7
2.8 VDC
IN ALARM
(–)
(+)
24 VAC (+10%, –15%)
FULL WAVE RECTIFIED,
UNFILTERED POWER
MAY BE USED
RTS451KEY
REMOTE TEST STATION DH400
DUCT DETECTOR
METHOD #2 — AUX POWER LOCATED AT TEST STATION
A78-2351-10
Figure 2. RTS451KEY wiring diagram for DH400ACDC,
stand-alone configuration (See Note 1 for use with
FACP):
NOTE 1: When utilizing an FACP, trouble contacts (10 and
11) should be wired as shown in Figure 6 of the
DH400ACDC installation manual. The
RTS451KEY supervisory terminal (6) should not
be used.
A78-2609-01
Figure 3. RTS451KEY wiring diagrams for DH400:
NOTE: Terminal 6 of the RTS451KEY is not used when
wired to a 2-wire detector.
5
6
3
4
ALARM (+)
AUX POWER (–)
RESET (–)
TEST (–)
7
1
2
4
3
5
RESET
TEST
6
DH400ACDC
Duct Smoke Detector RTS451KEY
Remote Test Station
SIGNAL
AUX POWER (+)
SUPERVISORY
CONTACTS
11
10
{
See Note 1
Figure 4. Test Coil installation:
NOTE: Test coil is NOT used with some detectors. Please
refer to the detector installation manual for more
information.
DETECTOR
HEAD
TEST COIL
A78-1994-01
Wiring Instructions
Consult the appropriate detector installation instructions
for the applicable wiring diagram. The RTS451KEY mounts
to a single gang box (21/2˝ minimum depth).
In Canadian applications, the RTS451KEYA is intended to
be located in the same room as the smoke detector and
within 60 feet of the unit.
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Pittway Équipement de test
Manuels Équipement de test populaires d'autres marques
SMART
SMART KANAAD SBT XTREME 3G Series Manuel utilisateur
Agilent Technologies
Agilent Technologies BERT Serial Manuel utilisateur
Agilent Technologies
Agilent Technologies N3280A Manuel utilisateur
Vernier
Vernier Go Direct Voltage Manuel utilisateur
Lifeloc
Lifeloc R.A.D.A.R. Manuel utilisateur
Fluke
Fluke T5-600 Instructions d'utilisation et d'installation
