Pit Boss Ultimate Griddle PB5BGD2 Manuel utilisateur

300522

MODEL / MODÈLE / MODELO : PB5BGD2

PART / PIÈCE / PARTE : 10783, 10847

WARNING: PLEASE READ THE ENTIRE

MANUAL BEFORE INSTALLATION AND

USE OF THIS GAS APPLIANCE. FAILURE

TO FOLLOW THESE INSTRUCTIONS

COULD RESULT IN PROPERTY

DAMAGE, BODILY INJURY OR EVEN

DEATH. CONTACT LOCAL BUILDING OR

FIRE OFFICIALS ABOUT RESTRICTIONS

AND INSTALLATION INSPECTION

REQUIREMENTS IN YOUR AREA.

AVERTISSEMENT : VEUILLEZ LIRE

L'INTÉGRALITÉ DU MANUEL AVANT

INSTALLATION ET UTILISATION DE CET

APPAREIL À GAZ. LE NON-RESPECT DE

CES INSTRUCTIONS PEUT ENTRAÎNER

DES DOMMAGES MATÉRIELS, DES

DOMMAGES CORPORELS OU MÊME

LA MORT. CONTACTEZ LES AUTORITÉS

LOCALES COMPÉTENTES CONCERNANT

LES RESTRICTIONS ET LES EXIGENCES

D'INSPECTION EN VIGUEUR DANS

VOTRE RÉGION.

ADVERTENCIA:LEATODOEL MANUAL

ANTES DE MONTAR Y USAR ESTA

BARBACOA DE GAS. SI NO SE SIGUEN

ESTAS INSTRUCCIONES, PUEDEN

PRODUCIRSE DAÑOS MATERIALES,

LESIONES CORPORALES O INCLUSO

LA MUERTE. PÓNGASE EN CONTACTO

CON LOS ADMINISTRADORES DEL

EDIFICIO O CON LOS BOMBEROS PARA

CONSULTAR LAS RESTRICCIONES Y LOS

REQUISITOS DE INSPECCIÓN DE LAS

INSTALACIONES DE SU ZONA.

 

 ' |   

5 

 

IMPORTANT, READ CAREFULLY, RETAIN

FOR FUTURE REFERENCE. MANUAL MUST

BE READ BEFORE OPERATING!

  

5   

IMPORTANT, PRENEZ CONNAISSANCE DE

CE DOCUMENT ET CONSERVEZ-LE POUR

RÉFÉRENCE ULTÉRIEURE. VOUS DEVEZ LIRE

CE GUIDE AVANT D’UTILISER LE BARBECUE!

  5

 

IMPORTANTE, LEER DETENIDAMENTE,

CONSERVAR PARA REFERENCIA FUTURA.

LEA EL MANUAL ANTES DEL USO!

FOR OUTDOOR AND HOUSEHOLD USE ONLY. NOT FOR COMMERCIAL USE. FUEL

AND ACCESSORIES NOT INCLUDED.

RÉSERVÉ À L’USAGE EXTÉRIEUR ET RÉSIDENTIEL UNIQUEMENT. NON DESTINÉ À

UN USAGE COMMERCIAL. COMBUSTIBLE ET ACCESSOIRES NON INCLUS.

SOLO PARA USO EN EXTERIORES Y EN EL HOGAR. NO ES PARA USO COMERCIAL.

NO INCLUYE COMBUSTIBLE NI ACCESORIOS

ENGLISH

may be copied, transmitted, transcribed, stored in a retrieval

system, in any form or by any means without expressed

written permission of,

Dansons

3411 North 5th Avenue, Suite 500, Phoenix, ,  85013

www.pitboss-grills.com

Customer Care

USA: (480) 923-9630

Canada (Toll-Free): 1-877-942-2246

  

Parts & Specs...................................................................... 2

Assembly Preparation...................................................... 3

Assembly Instructions

Installing The Locking Casters...................................................4

Mounting The Cart Panels..........................................................5

Securing The Drawer Rails..........................................................6

Mounting The Drawer Support Bar .........................................6

Installing The Heat Shield ..........................................................6

Mounting The Swing Drawer .................................................... 7

Installing The Drawer.................................................................. 7

Installing The Cabinet Door To The Cart ................................. 7

Mounting The Bottle Opener....................................................8

Securing The Side Shelf Brackets..............................................8

Installing The Side Shelves.........................................................8

Mounting The Lid Handle...........................................................9

Securing The Lid Support ...........................................................9

Installing The Firebox To The Cart............................................9

Inserting The Hot Plate Screws...............................................10

Placing The Cooking Components.......................................... 10

Installing The Ignition Battery................................................10

ENGLISH

  

MODEL ASSEMBLED (WxDxH) WEIGHT COOKING AREA BTU/HR

 52 1,600   674   1022 

/ 62.9   26.5   40.2  72.0 

/ 158.7  4,174 

/ 647.0  50,000

Part# Description

1 Firebox (x1)

2 Hot Plate (x1)

3 Hot Plate Leg Screws (x4)

4 Grease Cup (x1)

5 Lid Support (x1)

6 Lid Handle Bezel (x2)

7 Lid Handle (x1)

8 Side Shelf - Left (x1)

9 Side Shelf - Right (x1)

10 Side Shelf Bracket - Left (x2)

11 Side Shelf Bracket - Right (x2)

12 Bottle Opener (x1)

13 Cart Side Panel - Left (x1)

14 Cart Partition (x1)

15 Cart Side Panel - Right (x1)

16 Cart Back Panel (x1)

17 Cabinet Door (x1)

18 Drawer Rails (x1)

19 Drawer Support Bar (x1)

20 Heat Shield (x1)

21 Cart Front Panel (x1)

22 Cart Bottom (x1)

23 Swing Drawer (x1)

24 Drawer Front (x1)

25 Drawer (x1)

26 Locking Caster (x4)

A Screw (x54)

B Screw (x2)

C Locking Washer (x14)

D Washer (x14)

E Screw (x14)

F Screw (x6)

G Battery (x1)

NOTE: Due to ongoing product development, parts are subject to change without notice. Contact

Customer Service if parts are missing when assembling the unit.

16 12

25 26

  

 

 

ENGLISH

 

IMPORTANT: It is advised to read each step entirely before starting assembly on instructions. Do not tighten screws

completely until all screws for that step have been installed. Hardware combination involving a locking washer and

washer should be installed with the locking washer closest to the head of the screw.

1.    

Parts Required:

1 x Cart Bottom (#22)

4 x Locking Caster (#26)

Installation:

• Place a piece of cardboard on the floor to prevent scratching the unit

and parts during assembly.

• Turn over the Cart Bottom so it lies flat-side down on the cardboard.

Insert a Locking Caster to the bottom-corner of the Cart Bottom and

hand-tighten by rotating into the hole. The Locking Caster is inserted

completely when it cannot rotate any further into the Cart Bottom.

Repeat installation for the other three Locking Casters.

 

Parts are located throughout the shipping carton, including underneath the griddle. Inspect the unit, parts, and hardware blister

pack after removing from the protective shipping carton. Discard all packaging materials from inside and outside of the griddle

before assembly, then review and inspect all parts by referencing the parts list. If any part is missing or damaged, do not attempt

to assemble. Shipping damage is not covered under warranty. Contact your dealer or Pit Boss® Grills Customer Care for parts.

www.pitboss-grills.com

IMPORTANT: Using two people is necessary when assembling this unit.

Tools required for assembly: screwdriver and wrench.

Tools not included.

ENGLISH

2.    

Parts Required:

1 x Cart Side Panel - Left (#13)

1 x Cart Partition (#14)

1 x Cart Side Panel - Right (#15)

1 x Cart Back Panel (#16)

1 x Cart Front Panel (#21)

26 x Screw (#A)

Installation:

• Install the Cart Side Panel Left to the Cart Bottom using five screws.

Repeat the same installation for the Cart Side Panel Right using another

five screws. Note illustration 2A.

NOTE: To ensure the Cart Side Panels are arranged correctly, verify

that the Cart Side Panel Left has two holes facing the front for the

bottle opener installation in future steps.

• Place the Cart Back Panel between the Cart Side Panels, flat side facing

outward. Secure using three screws into each Cart Side Panel. Note

illustration 2B.

NOTE: Once installed, the exterior of the cart should be flush with

the Cart Bottom.

• Position the Cart Partition on the Cart Bottom as shown. Note the

position of the mounting holes and that the edge facing the front has

no holes. Secure the Cart Partition by using three screws into the Cart

Bottom and two screws into the Cart Back Panel. Note illustration 2C.

• Align the holes of the Cart Front Panel and the Cart Partition, then

secure using on screws. Next, secure the Cart Front Panel into the Cart

Side Panels using two screws on each side. Note illustration 2D.

2

2

2

2



ENGLISH

3.    

Parts Required:

1 x Drawer Rails (#18)

5 x Screw (#A)

Installation:

• Align the holes of the Drawer Rails to the holes on the left side of the

Cart Bottom, then secure using five screws, as shown.

4.     

Parts Required:

1 x Drawer Support Bar (#19)

2 x Screw (#A)

Installation:

• Insert the tab of the Drawer Support into the Cart Partition, then secure

the Drawer Support using two screws, one on each side.

5.    

Parts Required:

1 x Heat Shield (#20)

6 x Screw (#E)

Installation:

• Place the Heat Shield into the body of the Cart with the brackets on the

left side, as shown in illustration. Align the mounting holes and secure

using six screws.

IMPORTANT: The upward edge of the Heat Shield should be facing

the front of the unit.





ENGLISH

6.    

Parts Required:

1 x Swing Drawer (#23)

2 x Screw (#F)

Installation:

• Place the Swing Drawer into the top section of the left-side of the Cart,

with the handle facing the front. Rest the Swing Drawer on the Drawer

Support Bar, then anchor each corner using one screw.

NOTE: Once installed, Swing Drawer should be able to tip open and

close with ease.

7.   

Parts Required:

1 x Drawer Front (#24)

1 x Drawer (#25)

8 x Screw (#E)

Installation:

• Assemble the Drawer by mounting the Drawer Front to the Drawer

using eight screws. Note illustration 7A.

• Align the rails of the Drawer to insert into the bottom section of the left-

side of the Cart. Slide the rails into rail mounts, then push the Drawer

into the Cart body. Note illustration 7B.

NOTE: Once installed, the assembed Drawer and Swing Drawer

should be flush with the Cart body and Cart Bottom.

8.       

Parts Required:

1 x Cabinet Door (#17)

Installation:

• Align the Cabinet Door with the right section of the Cart. Insert the

bottom pin into the pivot hole on the right side of the Cart Bottom,

then push down on the locking-loaded top pin, and lock into the hole on

the Cart Front Panel.

IMPORTANT: The Cabinet Door should swing freely once installed,

and line up with the door magnet. If unlevel, ensure the top and

bottom pins of the Cabinet Door are inserted correctly.

7

7

23 





ENGLISH

9.    

Parts Required:

1 x Bottle Opener (#12)

2 x Screw (#A)

Installation:

• Mount the Bottom Opener to the Front-Left corner of the Cart using

two screws. Note illustration for correct orientation, with opening

angled downwards.

10.     

Parts Required:

2 x Side Shelf Bracket - Left (#10)

2 x Side Shelf Bracket - Right (#11)

12 x Screw (#A)

12 x Locking Washer (#C)

12 x Washer (#D)

Installation:

• Mount one Side Shelf Bracket to a Cart Side Panel using three washers,

locking washers and screws. Install each screw halfway first, then

tighten completely when all three screws are mounted and aligned

properly. Repeat installation for the other three Side Shelf Brackets.

11.    

Parts Required:

1 x Side Shelf - Left (#8)

1 x Side Shelf - Right (#9)

4 x Screw (#F)

Installation:

• Align and position one Side Shelf on the Side Shelf Brackets on one side

of the unit. From underneath, secure a screw into each corner, as shown

in illustration. Repeat same installation for the Side Shelf on the other

side of the unit.

NOTE: Once installed, both Side Shelves can be raised (for use) or

lowered (for storage) with ease.

IMPORTANT: Avoid using the Side Shelves to move or lift the unit.

The weight of the unit will cause the shelves to break, which is not

covered by warranty.







ENGLISH

12.    

Parts Required:

1 x Firebox (#1)

2 x Lid Handle Bezel (#6)

1 x Lid Handle (#7)

2 x Screw (#B)

2 x Locking Washer (#C)

2 x Washer (#D)

Installation:

• Place a locking washer then a washer onto a screw. From inside the

lid of the Firebox, insert one screw to protrude to the outside. Add a

Lid Handle Bezel on the screw, then hand-tighten the screw (from the

inside) into the Lid Handle.

• Repeat same installation for the other end of the Lid Handle.

13.    

Parts Required:

1 x Lid Support (#5)

3 x Screw (#A)

Installation:

• On the backside of the Firebox, fasten the Lid Support to the center of

the panel using three screws.

14.      

Parts Required:

4 x Screw (#A)

Installation:

• Place the Firebox next to the Cart, both facing the same direction.

Using two people, lift the Firebox and slowly place onto the Cart. Note

illustration 14A.

IMPORTANT: The two tabs on each Cart Side Panel should be on the

outside of the Firebox.

• Once in position, secure the Firebox onto the Cart by using two screws

on each side. Note illustration 14B.

14

14















ENGLISH

15.     

Parts Required:

1 x Hot Plate (#2)

4 x Hot Plate Screws (#3)

Installation:

• Turn the Hot Plate upside-down. Insert a Hot Plate Screw into a corner

hole of the Hot Plate, turning by hand, until it cannot rotate any further

into the nut. Repeat same installation on the other three corner holes.

16.    

Parts Required:

1 x Grease Cup (#4)

Installation:

• Open the Firebox lid. Carefully, place the Hot Plate into the Firebox. Once

the Hot Plate is installed, ensure it sits level in the Firebox. Adjust the

height of the Hot Plate Screws, if needed, so the Hot Plate is level.

NOTE: To maintain the searing and grilling performance of your Hot

Plate, regular care and maintenance is required.

• Place the Grease Cup into the Grease Cup housing on the left side of the

Firebox, as shown in the illustration.

17.    

Parts Required:

1 x Battery (#G)

Installation:

• Turn the ignition button cap counter-clockwise to remove it. Insert the

Battery into the housing with the positive (+) terminal facing outward.

Screw the ignition button cap back into place to cover.

• The unit is now completely assembled.



Ce manuel convient aux modèles suivants

Table des matières

Langues :

Autres manuels Pit Boss Plaque

Pit Boss

Pit Boss Sportsman PB2BSPD Manuel utilisateur

Pit Boss

Pit Boss PB4BGS1 Manuel utilisateur

Pit Boss

Pit Boss PB5BGD Manuel utilisateur

Pit Boss

Pit Boss Ultimate Griddle PB2BGD2 Manuel utilisateur

Pit Boss

Pit Boss Ultimate Griddle PB2BGD2 Manuel utilisateur

Pit Boss

Pit Boss Ultimate Griddle Series Manuel utilisateur

Pit Boss

Pit Boss PB2BGT1 Manuel

Pit Boss

Pit Boss 757GS Series Instructions d'installation

Pit Boss

Pit Boss PB2BGT1 Instructions d'installation

Pit Boss

Pit Boss PB757GS Manuel utilisateur

Pit Boss

Pit Boss 336GS Instructions d'installation

Pit Boss

Pit Boss 200GS Instructions d'installation

Pit Boss

Pit Boss PB5BGD Manuel utilisateur

Pit Boss

Pit Boss Ultimate Griddle Series Manuel utilisateur

Pit Boss

Pit Boss PB757GS Manuel utilisateur

Pit Boss

Pit Boss PB336GS Manuel utilisateur

Pit Boss

Pit Boss PB2BGD2, PB3BGD2, PB4BGD2, PB5BGD2 Manuel utilisateur

Pit Boss

Pit Boss Ultimate Griddle PB3BGD2 Manuel utilisateur

Manuels Plaque populaires d'autres marques

Proctor-Silex

Proctor-Silex 25340 Manuel utilisateur

New House Kitchen

New House Kitchen NH33-C Manuel utilisateur

Magikitch'n

Magikitch'n 24 Manuel utilisateur

Black Stone

Black Stone 1650 Manuel utilisateur

Anvil

Anvil FTA7116 Manuel utilisateur

Presto

Presto 07030 Manuel utilisateur

Dyna-Glo

Dyna-Glo DGL260SNP Manuel utilisateur

Char-Broil

Char-Broil 19952085 Manuel utilisateur

APW Wyott

APW Wyott HMG-2424 Manuel utilisateur

Airxcel

Airxcel Suburban Elite SOP-1005A Manuel utilisateur

Keating Of Chicago

Keating Of Chicago MIRACLEAN PRE-2000 Manuel utilisateur

Nexgrill

Nexgrill 720-0786A Manuel utilisateur

Outwell

Outwell FH-3047C Manuel utilisateur

Rankam

Rankam Member's Mark GR2298901-MM-02 Guide de référence rapide

Black Stone

Black Stone 1972 Manuel utilisateur

Star

Star Ultra Max 760TA Manuel utilisateur

NuWave

NuWave Precision Cast Iron Griddle Manuel d'utilisation

BERJAYA

BERJAYA EG 1750 Manuel utilisateur