Pioneer SX-950 Guide de référence

SX-950 ALIGNMENT PROCEDURES

9.1 AM SECTION

1. Set function switch to AM.

2. Connect AM signal generator through 1k-ohm

resistor to AM antenna terminal.

3. Set DUPLICATE switch to OFF and connect

an AC voltmeter to TAPE 1 REC jacks.

4. Set AM SG for 400Hz 30% modulation 100dB

output.

5. Set SX-950 dial indication and AM SG

frequency for 600kHz.

6. Adjust T8 core for maximum reading on AC

voltmeter.

7. Set SX-950 dial indication and AM SG

frequency for 1,400kHz.

8. Adjust TC5 for maximum reading on AC

voltmeter.

9. Set AM SG for 30dB output.

10. Set SX-950 dial indication and AM SG

frequency for 600kHz.

11. Adjust T7, T8 and bar antenna core for

maximum reading on AC voltmeter.

12. Set SX-950 dial indication and AM SG

frequency for 1,400kHz.

13. Adjust TC5, TC6 and TC7 for maximum

reading on AC voltmeter.

14. Repeat steps 10-13 to eliminate variations in

AC voltmeter readings.

9.2 FM TUNER

1. Set function switch to FM.

2. Set FM MUTING switch to OFF.

3. Connect FM signal generator through 300-ohm

dummy load to 300 ohm FM antenna terminals.

4. Set DUPLICATE switch to OFF and connect

AC voltmeter to TAPE 1 REC jacks.

5. Set FM SG for 100dB output at 400Hz and

100% modulation.

6. Set SX-950 dial indication and FM SG

frequency for 87.4MHz.

7. Adjust T4 core for maximum indication on

SIGNAL meter.

8. Adjust T6 lower core for center of scale

indication on TUNING meter.

9. Set FM SG for 8dB output and adjust cores of

T1, T2, and T3 for maximum reading on AC

voltmeter.

10. Set FM SG for 100dB output.

11. Set SX-950 dial indication and FM SG

frequency for 106MHz.

12. Adjust TC4 for maximum indication on

SIGNAL meter.

13. Set FM SG for 8dB output and adjust TC1,

TC2 and TC3 for maximum reading on AC

voltmeter.

14. Set FM SG for 100dB output.

15. Set SX-950 dial indication and FM SG

frequency for 87.4MHz.

16. Adjust T4 core for maximum indication on

SIGNAL meter.

17. Set FM SG for 8dB output and adjust cores of

T1, T2 and T3 for maximum reading on AC

voltmeter.

18. Repeat steps 10-17 to eliminate variations in

AC voltmeter readings.

19. After completing above adjustments, adjust T5

core for maximum reading on AC voltmeter.

20. Detune SX-950 to where only noise is

received and adjust T6 lower core for center of

scale indication on TUNING meter.

21. Set FM SG for 98MHz 60dB output.

22. Tune SX-950 for exact center of scale

indication on TUNING meter.

23. Adjust T6 upper core for minimum distortion.

24. Repeat steps 20- 23 to eliminate variations in

point of minimum distortion.

25. Set FM SG for 100dB output and adjust VR3

so that SIGNAL meter indicates 5 of the scale.

Multiplex Decoder

26. Connect MPX SG (multiplex signal generator)

to the external modulator terminals of the FM

SG and set the FM SG for external

modulation.

27. Connect PILOT OUT terminal of MPX SG to

horizontal input terminal of oscilloscope.

28. Through probe, connect oscilloscope vertical

input terminal to terminal No. 19.

29. Set FM SG for 98MHz 60dB output

unmodulated.

30. Tune SX-950 for exact center of scale

indication on TUNING meter.

31. Adjust VR1 so that 4:1 frequency ratio

Lissajous' (see note below) figure becomes

stationary.

32. Set FM SG for 1kHz (L or R), ?67.5kHz

deviation, 19kHz (pilot signal) and +7.5kHz

modulation.

33. Adjust VR2 for minimum L-R crosstalk.

Note:

Signal at terminal No. 19 is 76kHz sawtooth wave

and MPX SG pilot out is a 19kHz sine wave.

These form a Lissajous figure as shown in Fig.

23.

FM Alignment

If FM stations have drifted in their indicated positions on the dial you might be able to get the FM

Local Oscillator back to where it belongs with a bit of luck and careful adjustment.

Set the SX-950 tuning pointer to about 98 MHz, at the indicated frequency of a known station very

close to 98. Then get another FM receiver tuned to this station to hear the audio content. Verify that

the movable fins of the SX-950 tuning variable capacitor are at their approximate midpoint as well.

This is critical.

Attempt to adjust TC4to locate and tune the known station. Basically you are going to walk the tuning

to the correct indicated position. This adjustment will be extremely sensitive. Ideally a plastic tool

with a metal blade would be used to trim this adjustment (such as a trimpot tool) but a micro

screwdriver may suffice. Be aware the metal screwdriver shaft can affect the capacitance or

inductance of the device being adjusted. Anticipate this factor to get it close once the tool is moved

away from the device.

IF YOU GET LOST, stop at a station, then use the other FM receiver to match the audio and read the

frequency.

Alternately, you can also begin with the tuner set to 98MHz, tune TC4to the first audio you can find,

then find the station frequency with the other receiver. Adjust the SX-950 to the next station's audio,

determine where you are at and keep on repeating until the station is located.

9.3 POWER AMPLIFIER SECTION

1. Turn VR3 and VR4 fully counter-clockwise before

turning on the power.

2. Remove jumper plugs connecting POWER IN and PRE

OUT jacks.

3. Connect 5.1 K-ohm resistor to POWER IN jacks.

4. Set power amplifier for no load.

5. Set POWER switch to ON.

6. Adjust VR1 for 0V between terminals No. 10 and No. 9.

7. Adjust VR2 for 0V between terminals No. 25 and No.

24.

8. Adjust VR3 for 20mV between terminals No. 12(+) and

No. 13(-).

9. Adjust VR4 for 20mV between terminals No. 27(+) and

No. 28(-).

10. Allow set to warm up for at least 10 minutes, then

readjust.

Autres manuels pour SX-950

Autres manuels Pioneer Récepteur stéréo

Pioneer

Pioneer SX-V90 Manuel utilisateur

Pioneer

Pioneer VSX-834 Manuel

Pioneer

Pioneer AVH-4850BT Manuel utilisateur

Pioneer

Pioneer VSX-D908TX Manuel utilisateur

Pioneer

Pioneer VSX-502 Manuel utilisateur

Pioneer

Pioneer VSX-1127 Manuel utilisateur

Pioneer

Pioneer VSX-455 Manuel utilisateur

Pioneer

Pioneer MVH-AV251BT Manuel utilisateur

Pioneer

Pioneer DMH-T450EX Manuel utilisateur

Pioneer

Pioneer Elite VSX-37TX Manuel utilisateur

Pioneer

Pioneer SX-680 Manuel utilisateur

Pioneer

Pioneer XR-VS200 Manuel utilisateur

Pioneer

Pioneer VSX-D506S Manuel utilisateur

Pioneer

Pioneer SX-319V-K Manuel utilisateur

Pioneer

Pioneer QX-949A Series Manuel utilisateur

Pioneer

Pioneer AVH-X5550BT Manuel utilisateur

Pioneer

Pioneer SX-626 KCW Guide de démarrage rapide

Pioneer

Pioneer SX-1250 Manuel utilisateur

Pioneer

Pioneer VSX-D603S Manuel utilisateur

Pioneer

Pioneer VSX-4950S Manuel utilisateur

Pioneer

Pioneer AVH-2350DVD Manuel utilisateur

Pioneer

Pioneer VSX-D3S Manuel utilisateur

Pioneer

Pioneer DMH-341EX Manuel utilisateur

Pioneer

Pioneer VSX-D510 Manuel utilisateur

Manuels Récepteur stéréo populaires d'autres marques

Marantz

Marantz CINEMA 70S Manuel utilisateur

Kenwood

Kenwood KMDX92 Manuel utilisateur

Yamaha

Yamaha RX-830 Manuel utilisateur

Yamaha

Yamaha RX-750 Manuel utilisateur

Denon

Denon AVR-1311 Manuel utilisateur

Denon

Denon AVR-S760H Manuel utilisateur

Denon

Denon AVR-X7200W Manuel utilisateur

Sony

Sony XAV-1500 Manuel utilisateur

Radio Shack

Radio Shack DX-399 Manuel utilisateur

Sony

Sony STR-DE535 - Fm Stereo/fm-am Receiver Manuel utilisateur

Yamaha

Yamaha MusicCast TSR-5B3D Manuel utilisateur

Sony

Sony STR-DE335 - Fm Stereo/fm-am Receiver Manuel utilisateur

Sony

Sony STR-DG500 - Multi Channel Av Receiver Manuel utilisateur

Panasonic

Panasonic AJSD955B - DVCPRO50 STUDIO DECK Manuel utilisateur

Sherwood

Sherwood S-2660CP Manuel technique

Sony

Sony STR-K790 - Lifier Manuel utilisateur

Denon

Denon DRA-697CI Manuel utilisateur

SMART-AVI

SMART-AVI HDX-PRO Series Manuel utilisateur