Pioneer GM-6500F Manuel utilisateur

Owner’s Manual

Mode d’emploi

BRIDGEABLE FOUR-CHANNEL POWER AMPLI-

FIER

AMPLIFICATEUR DE PUISSANCE PONTABLE À

QUATRE CANAUX

AMPLIFICATORE DI POTENZA A QUATTRO CANA-

LI COLLEGABILE A PONTE

AMPLIFICADOR DE POTENCIA DE CUATRO CA-

NALES EN PUENTE

SCHAKELBARE 4-KANAALSVERSTERKER

BRÜCKBARER 4-KANAL-LEISTUNGSVERSTÄR-

KER

ЧЕТЫРЕХКАНАЛЬНЫЙ УСИЛИТЕЛЬ МОЩНО-

СТИ С ВОЗМОЖНОСТЬЮ МОСТОВОГО ВКЛЮЧЕ-

НИЯ

GM-6500F

English NederlandsDeutschEspañolItalianoFrançais Русский

If you want to dispose this product, do not mix

it with general household waste. There is a se-

parate collection system for used electronic

products in accordance with legislation that re-

quires proper treatment, recovery and recy-

cling.

Private households in the member states of

the EU, in Switzerland and Norway may return

their used electronic products free of charge

to designated collection facilities or to a retai-

ler (if you purchase a similar new one).

For countries not mentioned above, please

contact your local authorities for the correct

method of disposal.

By doing so you will ensure that your disposed

product undergoes the necessary treatment,

recovery and recycling and thus prevent po-

tential negative effects on the environment

and human health.

Thank you for purchasing

this PIONEER product.

To ensure proper use, please read through this

manual before using this product. It is espe-

cially important that you read and observe

WARNINGs and CAUTIONs in this manual.

Please keep the manual in a safe and accessible

place for future reference.

Visit our website

Visit us at the following site:

http://www.pioneer.co.uk

!Register your product. We will keep the de-

tails of your purchase on file to help you

refer to this information in the event of an

insurance claim such as loss or theft.

!We offer the latest information about

PIONEER CORPORATION on our

website.

In case of trouble

Should this product fail to operate properly,

please contact your dealer or nearest author-

ized Pioneer Service Station.

Before connecting/

installing the amplifier

WARNING

!The use of a special red battery and ground

wire RD-223, available separately, is recom-

mended. Connect the battery wire directly to

the car battery positive terminal +and the

ground wire to the car body.

!This unit is for vehicles with a 12 V battery and

negative grounding. Before installing in re-

creational vehicles, trucks or buses, check the

battery voltage.

!Always use a fuse of the rating prescribed.

The use of an improper fuse could result in

overheating and smoke, damage to the pro-

duct and injury, including burns.

!Check the connections of the power supply

and speakers if the fuse of the separately sold

battery wire or the amplifier fuse blows. Deter-

mine and resolve the cause, then replace the

fuse with and identical equivalent.

!Do not allow this unit to come into contact

with liquids. Electrical shock could result.

Also, damage to this unit, smoke, and over-

heating could result from contact with liquids.

The surfaces of the amplifier and any attached

speakers may also heat up and cause minor

burns.

Section

01 Before you start

!In the event of any abnormality, the power

supply to the amplifier is cut off to prevent

equipment malfunction. If this occurs, switch

the system power off and check the power

supply and speaker connections. If you are un-

able to determine the cause, please contact

your dealer.

!Always disconnect the negative *terminal of

the battery beforehand to avoid the risk of

electric shock or short circuit during installa-

tion.

CAUTION

!Always keep the volume low enough to hear

outside sounds.

!Extended use of the car stereo while the en-

gine is at rest or idling may exhaust the bat-

tery.

About the Protection function

The Protection function will operate in the condi-

tions outlined below. If the Protection function is

turned on, the power indicator will turn off, and

the amplifier will shut down.

!If the speaker output terminal and speaker

wire is short-circuited.

!If the temperature inside the amplifier gets too

high.

!If a DC voltage is applied to the speaker out-

put terminal.

En 3

English

Section

Before you start

What’s what

Front side

Rear side

To adjust the switch, use a flathead screwdri-

ver if needed.

1LPF (low-pass filter)/HPF (high-pass fil-

ter) select switch

Switch the settings based on the connected

speaker.

!When the Subwoofer is connected:

Select LPF. This eliminates high range

frequency and outputs low range fre-

quency.

!When the full range speaker is con-

nected:

Select HPF or OFF.HPF eliminates low

range frequency and output high range

frequency. OFF outputs the entire fre-

quency range.

2GAIN (gain) control

Adjusting gain controls CHANNEL A (chan-

nel A) and CHANNEL B (channel B) helps

align the car stereo output to the Pioneer

amplifier. Default setting is the NORMAL

position.

If output remains low, even when the car

stereo volume is turned up, turn controls to

lower level. If distortion occurs when the car

stereo volume is turned up, turn these con-

trols to higher level.

!If using only one input plug, set the gain

controls for speaker outputs A and B to

the same position.

!For use with an RCA equipped car stereo

(standard output of 500 mV), set to the

NORMAL position. For use with an RCA

equipped Pioneer car stereo, with max.

output of 4 V or more, adjust level to

match that of the car stereo output.

3INPUT SELECT (input select) switch

Select 2CH for two-channel input and 4CH

for four–channel input.

!You can select input select only for con-

nections when using the RCA input jack.

For connections when using the speaker

input wire, 4CH will be used automati-

cally no matter which switch setting is

selected.

4FREQ (cut off frequency) control

Cut off frequency selectable from 40 Hz to

500 Hz if the LPF/HPF select switch is set to

LPF or HPF.

!You can select cut off frequency only for

CHANNEL B.

5Power indicator

The power indicator lights up to indicate

power ON.

Setting gain properly

!Protective function included to prevent

malfunction of the unit and/or speakers

due to excessive output, improper use or

improper connection.

!When outputting high volume sound etc.,

this function cuts off the output for a few

seconds as a normal function, but output

is restored when the volume of the head

unit is turned down.

!A cut in sound output may indicate impro-

per setting of the gain control. To ensure

continuous sound output with the head

unit at a high volume, set amplifier gain

control to a level appropriate for the preout

maximum output level of the head unit, so

that volume can remain unchanged and to

control excess output.

Section

02 Setting the unit

!Despite correct volume and gain settings,

the unit sound still cuts out periodically. In

such cases, please contact the nearest

authorized Pioneer Service Station.

Gain control of this unit

Preout level: 2 V

(Standard: 500 mV)

Above illustration shows NORMAL gain set-

ting.

Relationship between amplifier gain

and head unit output power

If amplifier gain is raised improperly, this will

simply increase distortion, with little increase

in power.

Signal waveform when outputting at

high volume using amplifier gain

control

Signal waveform distorted with high output, if

you raise the gain of the amplifier the power

changes only slightly.

En 5

English

Section

Setting the unit

Connection diagram

1Special red battery wire

RD-223 (sold separately)

After completing all other amplifier connec-

tions, finally connect the battery wire terminal

of the amplifier to the positive (+) battery

terminal.

2Ground wire (Black)

RD-223 (sold separately)

Connect to metal body or chassis.

3Car stereo with RCA output jacks (sold sepa-

rately)

4External output

If only one input plug is used, do not connect

anything to RCA input jack B.

5Connecting wire with RCA pin plugs (sold se-

parately)

6RCA input jack A

7RCA input jack B

8Speaker input terminal (use a connector in-

cluded)

Please see the following section for speaker

connection instructions. Refer to Connections

when using the speaker input wire on page 9.

9Speaker output terminals

Please see the following section for speaker

connection instructions. Refer to Connections

when using the speaker input wire on page 9.

aSystem remote control wire (sold separately)

Connect male terminal of this wire to the sys-

tem remote control terminal of the car stereo.

The female terminal can be connected to the

auto-antenna relay control terminal. If the car

stereo lacks a system remote control terminal,

connect the male terminal to the power term-

inal via the ignition switch.

bFuse (25 A) × 2

cFuse (30 A) × 2

dGrommet

eRear side

fFront side

Note

INPUT SELECT (input select) switch must be set.

For details, see Setting the unit on page 4.

Before connecting the

amplifier

WARNING

!Secure the wiring with cable clamps or adhe-

sive tape. To protect the wiring, wrap sections

in contact with metal parts in adhesive tape.

!Never cut the insulation of the power supply

to feed power to other equipment. Current ca-

pacity of the wire is limited.

CAUTION

!Never shorten any wires, the protection circuit

may malfunction.

!Never ground speaker wire directly or band to-

gether multiple speakers’negative (*) lead

wires.

Section

03 Connecting the units

!If the system remote control wire of the ampli-

fier is connected to the power terminal via the

ignition switch (12 V DC), the amplifier will re-

main on with the ignition whether the car

stereo is on or off, which may exhaust battery

if the engine is at rest or idling.

!Install and route the separately sold battery

wire as far as possible from the speaker wires.

Install and route the separately sold battery

wire, ground wire, speaker wires and the am-

plifier as far away as possible from the anten-

na, antenna cable and tuner.

About bridged mode

Speaker impedance is max. 4 W, please carefully

check. Improper connection to the amplifier may

result in malfunction or personal injury due to

burns from overheating.

For bridged mode for a two-channel amplifier,

with a 4 Wload, either wire two 8 Wspeakers in

parallel, Left +and Right *(Diagram A) or use a

single 4 Wspeaker. For other amplifiers, please

follow the speaker output connection diagram for

bridging shown on rear: two 8 Wspeakers in par-

allel for a 4 Wload or a single 4 Wspeaker per

channel.

For any further enquiries, contact your local

authorized Pioneer dealer or customer service.

About suitable

specification of speaker

Ensure speakers conform to the following

standards, otherwise there is a risk of fire,

smoke or damage. Speaker impedance is 2 W

to 8 W,or4Wto 8 Wfor two-channel and other

bridge connections.

Subwoofer

Speaker channel Power

Four-channel output Nominal input:

Min. 60 W

Two-channel output Nominal input:

Min. 180 W

Three-channel

Speaker output A

Nominal input:

Min. 60 W

Three-channel

Speaker output B

Nominal input:

Min. 180 W

Other than subwoofer

Speaker channel Power

Four-channel output Max. input:

Min. 120 W

Two-channel output Max. input:

Min. 360 W

Three-channel

Speaker output A

Max. input:

Min. 120 W

Three-channel

Speaker output B

Max. input:

Min. 360 W

Connecting the speakers

The speaker output mode can be four-channel,

three-channel (stereo and mono) or two-chan-

nel (stereo or mono). Connect the speaker

leads based on the mode and the figures

shown below.

En 7

English

Section

Connecting the units

Four-channel output

1Right

2Left

3Speaker out A

4Speaker out B

Three-channel output

1Right

2Left

3Speaker out A

4Speaker out B (Mono)

Two-channel output (Stereo)

1Speaker (Right)

2Speaker (Left)

Two-channel output (Mono)

1Speaker (Mono)

Connections when using

the RCA input jack

Connect the car stereo RCA output jack and

the RCA input jack of the amplifier.

Section

03 Connecting the units

Four-channel / Three-channel output

!Slide INPUT SELECT (input select) switch

to 4CH position.

1RCA input jack A

2RCA input jack B

3Connecting wires with RCA plugs (sold sepa-

rately)

4From car stereo (RCA output)

If only one input plug is used, e.g. when the

car stereo has only one output (RCA output),

connect the plug to RCA input jack A rather

than B.

Two-channel output (Stereo) / (Mono)

!Slide INPUT SELECT (input select) switch

to 2CH position.

1RCA input jack A

For two-channel output, connect the RCA

plugs to the RCA input jack A.

2Connecting wire with RCA pin plugs (sold se-

parately)

3From car stereo (RCA output)

Connections when using

the speaker input wire

Connect the car stereo speaker output wires

to the amplifier using the supplied speaker

input wire.

!Do not connect both the RCA input and the

speaker input at the same time.

1Car Stereo

2Speaker output

3White/black: CH A, Left *

4White: CH A, Left +

5Gray/black: CH A, Right *

6Gray: CH A, Right +

7Green/black: CH B, Left *

8Green: CH B, Left +

9Violet/black: CH B, Right *

aViolet: CH B, Right +

bSpeaker input connector

To speaker input terminal of this unit.

Connecting the power

terminal

The use of a special red battery and ground

wire RD-223, available separately, is recom-

mended. Connect the battery wire directly to

the car battery positive terminal +and the

ground wire to the car body.

En 9

English

Section

Connecting the units

WARNING

If the battery wire is not securely fixed to the term-

inal using the terminal screws, there is a risk of

overheating, malfunction and injury, including

minor burns.

1 Route battery wire from engine com-

partment to the vehicle interior.

After completing all other amplifier connec-

tions, finally connect the battery wire terminal

of the amplifier to the positive (+) battery

terminal.

1Positive (+) terminal

2Engine compartment

3Vehicle interior

4Fuse (30 A) × 2

5Insert the O-ring rubber grommet into the

vehicle body.

6Drill a 14 mm hole into the vehicle body.

2 Twist the battery wire, ground wire

and system remote control wire.

Twist

3 Attach lugs to wire ends.

Use pliers, etc., to crimp lugs to wires.

1Lug (sold separately)

2Battery wire

3Ground wire

4 Connect the wires to the terminal.

Fix the wires securely with the terminal

screws.

1System remote control terminal

2Ground terminal

3Power terminal

4Terminal screws

5Battery wire

6Ground wire

7System remote control wire

Connecting the speaker

output terminals

1 Use wire cutters or a utility knife to

strip the end of the speaker wires to ex-

pose about 10 mm of wire and then twist

the wire.

Twist

Section

03 Connecting the units

Autres manuels pour GM-6500F

Table des matières

Langues :

Autres manuels Pioneer Amplificateur de voiture

Pioneer

Pioneer GM-5000T Manuel utilisateur

Pioneer

Pioneer GM-4300F - Amplifier Manuel utilisateur

Pioneer

Pioneer GM-5000T Manuel utilisateur

Pioneer

Pioneer GM-A4604 Manuel utilisateur

Pioneer

Pioneer GM-6100F Manuel utilisateur

Pioneer

Pioneer GM-D7500M SERIES Manuel utilisateur

Pioneer

Pioneer GM-D8500M Manuel utilisateur

Pioneer

Pioneer GM-A6604 Manuel utilisateur

Pioneer

Pioneer GM-9027ZT/UC Manuel utilisateur

Pioneer

Pioneer GM6400F - Bridgeable Amplifier Manuel utilisateur

Pioneer

Pioneer GM-A3602 Manuel utilisateur

Pioneer

Pioneer GM-D510M Manuel utilisateur

Pioneer

Pioneer GM-5000T Manuel utilisateur

Pioneer

Pioneer PRS-D1200SPL - Premier Amplifier Manuel utilisateur

Pioneer

Pioneer GM-DX871/XEVUC Manuel utilisateur

Pioneer

Pioneer CDX-PD6 Manuel utilisateur

Pioneer

Pioneer PRS-D4000F - Premier Amplifier Manuel utilisateur

Pioneer

Pioneer GM-D7500M SERIES Manuel utilisateur

Pioneer

Pioneer GM-6200F Manuel utilisateur

Pioneer

Pioneer GM-5300T Manuel utilisateur

Pioneer

Pioneer GM120 Manuel utilisateur

Pioneer

Pioneer GM-X372 Manuel utilisateur

Pioneer

Pioneer PRS-D2000SPL - Premier Amplifier Manuel utilisateur

Pioneer

Pioneer GM5100T - 760 Watts Power Amplifier Manuel utilisateur

Manuels Amplificateur de voiture populaires d'autres marques

Cyfre

Cyfre CHACDMA-819 Manuel utilisateur

MTX

MTX Thunder Marine TM904 Manuel utilisateur

MTX

MTX Thunder TA Super TA92001 Mode d’emploi

Lanier

Lanier 480-0239 Instructions d'utilisation et d'entretien

Kenwood

Kenwood KAC-642 Manuel utilisateur

Jensen

Jensen XA4150 Manuel utilisateur

Sony

Sony XM-405EQX Marketing Specifications Manuel utilisateur

Audiopipe

Audiopipe AQX-660.2 Manuel utilisateur

Clarion

Clarion APA2001 APA2001 APA2001 Guide de démarrage rapide

Sony

Sony XM-7547 Manuel utilisateur

Alpine

Alpine PDX11000 - Amplifier Manuel utilisateur

Steg

Steg Qx Mos 105.4x Manuel utilisateur

JL Audio

JL Audio HD900/5 Manuel utilisateur

Memphis

Memphis 16-MC5.700 Manuel utilisateur

Audiopipe

Audiopipe APSM-1150 Manuel utilisateur

Boss Audio Systems

Boss Audio Systems Riot GT1000M Manuel utilisateur

Kenwood

Kenwood KAC-PS811D Manuel utilisateur

Fusion

Fusion CA-DA41400 Manuel utilisateur