Pioneer GM-3500T Manuel utilisateur

Owner’s Manual

Mode d’emploi

BRIDGEABLE TWO-CHANNEL POWER AMPLIFIER

AMPLIFICATEUR DE PUISSANCE PONTABLE À

DEUX CANAUX

AMPLIFICADOR DE POTENCIA DE DOS CANALES

EN PUENTE

GM-3500T

English EspañolFrançais

Thank you for purchasing

this PIONEER product.

To ensure proper use, please read through this

manual before using this product. It is espe-

cially important that you read and observe

WARNINGs and CAUTIONs in this manual.

Please keep the manual in a safe and accessible

place for future reference.

Information to User

Alteration or modifications carried out without

appropriate authorization may invalidate the

user’s right to operate the equipment.

After-sales service for

Pioneer products

Please contact the dealer or distributor from

where you purchased this unit for after-sales

service (including warranty conditions) or any

other information. In case the necessary infor-

mation is not available, please contact the

companies listed below:

Please do not ship your unit to the companies

at the addresses listed below for repair without

advance contact.

U.S.A.

Pioneer Electronics (USA) Inc.

CUSTOMER SUPPORT DIVISION

P.O. Box 1760

Long Beach, CA 90801-1760

800-421-1404

CANADA

Pioneer Electronics of Canada, Inc.

CUSTOMER SATISFACTION DEPARTMENT

340 Ferrier Street

Unit 2

Markham, Ontario L3R 2Z5, Canada

1-877-283-5901

905-479-4411

For warranty information please see the Lim-

ited Warranty sheet included with this unit.

Visit our website

Visit us at the following site:

http://www.pioneerelectronics.com

in Canada

http://www.pioneerelectronics.ca

1 Register your product. We will keep the details

of your purchase on file to help you refer to

this information in the event of an insurance

claim such as loss or theft.

2 Receive updates on the latest products and

technologies.

3 Download owner’s manuals, order product

catalogues, research new products, and

much more.

The Safety of Your Ears is in

Your Hands

Get the most out of your equipment by playing

it at a safe level—a level that lets the sound

come through clearly without annoying blar-

ing or distortion and, most importantly, with-

out affecting your sensitive hearing. Sound

can be deceiving. Over time, your hearing

“comfort level”adapts to higher volumes of

sound, so what sounds “normal”can actually

be loud and harmful to your hearing. Guard

against this by setting your equipment at a

safe level BEFORE your hearing adapts.

ESTABLISH A SAFE LEVEL:

!Set your volume control at a low setting.

!Slowly increase the sound until you can

hear it comfortably and clearly, without dis-

tortion.

!Once you have established a comfortable

sound level, set the dial and leave it there.

BE SURE TO OBSERVE THE FOLLOWING

GUIDELINES:

!Do not turn up the volume so high that you

can’t hear what’s around you.

!Use caution or temporarily discontinue use

in potentially hazardous situations.

!Do not use headphones while operating a

motorized vehicle; the use of headphones

may create a traffic hazard and is illegal in

many areas.

Section

01 Before you start

Before connecting/

installing the amplifier

WARNING

!Handling the cord on this product or cords as-

sociated with accessories sold with the pro-

duct may expose you to chemicals listed on

proposition 65 known to the State of California

and other governmental entities to cause can-

cer and birth defect or other reproductive

harm. Wash hands after handling.

!The use of a special red battery and ground

wire RD-223, available separately, is recom-

mended. Connect the battery wire directly to

the car battery positive terminal +and the

ground wire to the car body.

!This unit is for vehicles with a 12 V battery and

negative grounding. Before installing in re-

creational vehicles, trucks or buses, check the

battery voltage.

!Always use a fuse of the rating prescribed.

The use of an improper fuse could result in

overheating and smoke, damage to the pro-

duct and injury, including burns.

!Check the connections of the power supply

and speakers if the fuse of the separately sold

battery wire or the amplifier fuse blows. Deter-

mine and resolve the cause, then replace the

fuse with and identical equivalent.

!Do not allow this unit to come into contact

with liquids. Electrical shock could result.

Also, damage to this unit, smoke, and over-

heating could result from contact with liquids.

The surfaces of the amplifier and any attached

speakers may also heat up and cause minor

burns.

!In the event of any abnormality, the power

supply to the amplifier is cut off to prevent

equipment malfunction. If this occurs, switch

the system power off and check the power

supply and speaker connections. If you are un-

able to determine the cause, please contact

your dealer.

!Always disconnect the negative *terminal of

the battery beforehand to avoid the risk of

electric shock or short circuit during installa-

tion.

CAUTION

!Always keep the volume low enough to hear

outside sounds.

!Extended use of the car stereo while the en-

gine is at rest or idling may exhaust the bat-

tery.

About the Protection function

The Protection function will operate in the condi-

tions outlined below. If the Protection function is

turned on, the power indicator will turn off, and

the amplifier will shut down.

!If the speaker output terminal and speaker

wire is short-circuited.

!If the temperature inside the amplifier gets too

high.

!If a DC voltage is applied to the speaker out-

put terminal.

Important (Serial number)

The serial number is located on the bottom of

this unit. For your own security and convenience,

be sure to record this number on the enclosed

warranty card.

En 3

English

Section

Before you start

What’s what

Front side

Rear side

To adjust the switch, use a flathead screwdri-

ver if needed.

1LPF (low-pass filter) switch

Switch the settings based on the connected

speaker.

!When the Subwoofer is connected:

Select ON. This eliminates high range

frequency and outputs low range fre-

quency.

!When the full range speaker is con-

nected:

Select OFF.OFF outputs the entire fre-

quency range.

2GAIN (gain) control

If output remains low, even when the car

stereo volume is turned up, turn controls to

lower level. If distortion occurs when the car

stereo volume is turned up, turn these con-

trols to higher level.

!For use with an RCA equipped car stereo

(standard output of 500 mV), set to the

NORMAL position. For use with an RCA

equipped Pioneer car stereo, with max.

output of 4 V or more, adjust level to

match that of the car stereo output.

!If you hear too much noise when using

the speaker input terminals, turn the

gain control to higher level.

3Power indicator

The power indicator lights up to indicate

power ON.

Setting gain properly

!Protective function included to prevent

malfunction of the unit and/or speakers

due to excessive output, improper use or

improper connection.

!When outputting high volume sound etc.,

this function cuts off the output for a few

seconds as a normal function, but output

is restored when the volume of the head

unit is turned down.

!A cut in sound output may indicate impro-

per setting of the gain control. To ensure

continuous sound output with the head

unit at a high volume, set amplifier gain

control to a level appropriate for the preout

maximum output level of the head unit, so

that volume can remain unchanged and to

control excess output.

!Despite correct volume and gain settings,

the unit sound still cuts out periodically. In

such cases, please contact the nearest

authorized Pioneer Service Station.

Gain control of this unit

Preout level: 2 V

(Standard: 500 mV)

Above illustration shows NORMAL gain set-

ting.

Relationship between amplifier gain

and head unit output power

If amplifier gain is raised improperly, this will

simply increase distortion, with little increase

in power.

Section

02 Setting the unit

Signal waveform when outputting at

high volume using amplifier gain

control

Signal waveform distorted with high output, if

you raise the gain of the amplifier the power

changes only slightly.

En 5

English

Section

Setting the unit

Connection diagram

1Special red battery wire

RD-223 (sold separately)

After completing all other amplifier connec-

tions, finally connect the battery wire terminal

of the amplifier to the positive (+) battery

terminal.

2Ground wire (Black)

RD-223 (sold separately)

Connect to metal body or chassis.

3Car stereo with RCA output jacks (sold sepa-

rately)

4External output

5Connecting wire with RCA pin plugs (sold se-

parately)

6Speaker input terminal (use a connector in-

cluded)

Please see the following section for speaker

connection instructions. Refer to Connections

when using the speaker input wire on page 8.

7RCA input jack

8System remote control wire (sold separately)

Connect male terminal of this wire to the sys-

tem remote control terminal of the car stereo.

The female terminal can be connected to the

auto-antenna relay control terminal. If the car

stereo lacks a system remote control terminal,

connect the male terminal to the power term-

inal via the ignition switch.

9Speaker output terminals

Please see the following section for speaker

connection instructions. Refer to Connections

when using the speaker input wire on page 8.

aFuse (25 A)

bFuse (30 A) × 2

cGrommet

dRear side

eFront side

Before connecting the

amplifier

WARNING

!Secure the wiring with cable clamps or adhe-

sive tape. To protect the wiring, wrap sections

in contact with metal parts in adhesive tape.

!Never cut the insulation of the power supply

to feed power to other equipment. Current ca-

pacity of the wire is limited.

CAUTION

!Never shorten any wires, the protection circuit

may malfunction.

!Never ground speaker wire directly or band to-

gether multiple speakers’negative (*) lead

wires.

!If the system remote control wire of the ampli-

fier is connected to the power terminal via the

ignition switch (12 V DC), the amplifier will re-

main on with the ignition whether the car

stereo is on or off, which may exhaust battery

if the engine is at rest or idling.

!Install and route the separately sold battery

wire as far as possible from the speaker wires.

Install and route the separately sold battery

wire, ground wire, speaker wires and the am-

plifier as far away as possible from the anten-

na, antenna cable and tuner.

Section

03 Connecting the units

About bridged mode

Speaker impedance is max. 4 W, please carefully

check. Improper connection to the amplifier may

result in malfunction or personal injury due to

burns from overheating.

For bridged mode for a two-channel amplifier,

with a 4 Wload, either wire two 8 Wspeakers in

parallel, Left +and Right *(Diagram A) or use a

single 4 Wspeaker. For other amplifiers, please

follow the speaker output connection diagram for

bridging shown on rear: two 8 Wspeakers in par-

allel for a 4 Wload or a single 4 Wspeaker per

channel.

For any further enquiries, contact your local

authorized Pioneer dealer or customer service.

About suitable

specification of speaker

Ensure speakers conform to the following

standards, otherwise there is a risk of fire,

smoke or damage. Speaker impedance is 2 W

to 8 Wfor stereo connection, or 4 Wto 8 Wfor

monaural and other bridge connection.

Subwoofer

Speaker channel Power

Two-channel output Nominal input:

Min. 60 W

One-channel output Nominal input:

Min. 180 W

Other than subwoofer

Speaker channel Power

Two-channel output MAX input:

Min. 120 W

One-channel output MAX input:

Min. 370 W

Connecting the speakers

The speaker output mode can be two-channel

(stereo) or one-channel (mono). Connect the

speaker leads to suit the mode according to

the figures shown below.

Two-channel output (Stereo)

1Speaker (Left)

2Speaker (Right)

One-channel output

1Speaker (Mono)

En 7

English

Section

Connecting the units

Connections when using

the speaker input wire

Connect the car stereo speaker output wires

to the amplifier using the supplied speaker

input wire.

!Do not connect both the RCA input and the

speaker input at the same time.

1Car Stereo

2Speaker output

3White/black: Left *

4White: Left +

5Gray/black: Right *

6Gray: Right +

7Speaker input connector

To speaker input terminal of this unit.

Connecting the power

terminal

The use of a special red battery and ground

wire RD-223, available separately, is recom-

mended. Connect the battery wire directly to

the car battery positive terminal +and the

ground wire to the car body.

WARNING

If the battery wire is not securely fixed to the term-

inal using the terminal screws, there is a risk of

overheating, malfunction and injury, including

minor burns.

1 Route battery wire from engine com-

partment to the vehicle interior.

After completing all other amplifier connec-

tions, finally connect the battery wire terminal

of the amplifier to the positive (+) battery

terminal.

1Positive (+) terminal

2Engine compartment

3Vehicle interior

4Fuse (30 A) × 2

5Insert the O-ring rubber grommet into the

vehicle body.

6Drill a 14 mm (1/2 in.) hole into the vehicle

body.

2 Twist the battery wire, ground wire

and system remote control wire.

Twist

3 Attach lugs to wire ends.

Use pliers, etc., to crimp lugs to wires.

1Lug (sold separately)

2Battery wire

3Ground wire

4 Connect the wires to the terminal.

Fix the wires securely with the terminal

screws.

Section

03 Connecting the units

1System remote control terminal

2Ground terminal

3Power terminal

4Terminal screws

5Battery wire

6Ground wire

7System remote control wire

Connecting the speaker

output terminals

1 Use wire cutters or a utility knife to

strip the end of the speaker wires to ex-

pose about 10 mm (3/8 in.) of wire and

then twist the wire.

Twist

2 Attach lugs to wire ends.

Use pliers, etc., to crimp lugs to wires.

1Lug (sold separately)

2Speaker wire

3 Connect the speaker wires to the

speaker output terminals.

Fix the speaker wires securely with the term-

inal screws.

1Terminal screws

2Speaker wires

3Speaker output terminals

En 9

English

Section

Connecting the units

Before installing the amplifier

WARNING

!To ensure proper installation, use the supplied

parts in the manner specified. If any parts

other than those supplied are used, they may

damage internal parts of the amplifier, or be-

come loose causing the amplifier to shut

down.

!Do not install in:

—Places where it could injure the driver or

passengers if the vehicle stops suddenly.

—Places where it may interfere with the dri-

ver, such as on the floor in front of the dri-

ver’s seat.

!Install tapping screws in such a way that the

screw tip does not touch any wire. This is im-

portant to prevent wires from being cut by vi-

bration of the car, which can result in fire.

!Make sure that wires do not get caught in the

sliding mechanism of the seats or touch the

legs of a person in the vehicle as short-circuit

may result.

!When drilling to install the amplifier, always

confirm no parts are behind the panel and

protect all cables and important equipment (e.

g. fuel/brake lines, wiring) from damage.

CAUTION

!To ensure proper heat dissipation of the ampli-

fier, ensure the following during installation:

—Allow adequate space above the amplifier

for proper ventilation.

—Do not cover the amplifier with a floor mat

or carpet.

!Protection function may activate to protect the

amplifier against overheating due to installa-

tion in locations where sufficient heat cannot

be dissipated, continuous use under high-vo-

lume conditions, etc. In such cases, the am-

plifier shuts down until it has cooled to a

certain designated temperature.

!Avoid routing wires through hot areas, such

as near the heater outlet. Heat may damage

the insulation, resulting in a short-circuit

through the vehicle body.

!The optimal installation location differs de-

pending on the car model. Secure the ampli-

fier at a sufficiently rigid location.

!Firstly make temporary connections and

check to ensure the amplifier and system op-

erate properly.

!After installing the amplifier, confirm that the

spare tire, jack and tools can be easily re-

moved.

Example of installation on

the floor mat or chassis

1 Place the amplifier in the desired instal-

lation location.

Insert the supplied tapping screws (4 mm ×

18 mm) into the screw holes and push on the

screws with a screwdriver so they make an im-

print where the installation holes are to be lo-

cated.

2 Drill 2.5 mm (1/8 in.) diameter holes at

the imprints either on the carpet or directly

on the chassis.

3 Install the amplifier with the use of

supplied tapping screws (4 mm × 18 mm).

1Tapping-screws (4 mm × 18 mm)

2Drill a 2.5 mm (1/8 in.) diameter hole

3Floor mat or chassis

Section

04 Installation

Autres manuels pour GM-3500T

Table des matières

Langues :

Autres manuels Pioneer Amplificateur de voiture

Pioneer

Pioneer GM6400F - Bridgeable Amplifier Manuel utilisateur

Pioneer

Pioneer GM-6200F Manuel utilisateur

Pioneer

Pioneer GM-6500F Manuel utilisateur

Pioneer

Pioneer GM-D7500M SERIES Manuel utilisateur

Pioneer

Pioneer PRS-D800 Manuel utilisateur

Pioneer

Pioneer GM-D9500F Manuel utilisateur

Pioneer

Pioneer Premier PRS-D4100F Manuel utilisateur

Pioneer

Pioneer GM-5300T Manuel utilisateur

Pioneer

Pioneer GM-D8500M Manuel utilisateur

Pioneer

Pioneer GM-6500F Manuel utilisateur

Pioneer

Pioneer GM5100T - 760 Watts Power Amplifier Manuel utilisateur

Pioneer

Pioneer GM-X562 Manuel utilisateur

Pioneer

Pioneer PRS-D1200SPL - Premier Amplifier Manuel utilisateur

Pioneer

Pioneer GM-5300T Manuel utilisateur

Pioneer

Pioneer LEXUS RX330 Manuel utilisateur

Pioneer

Pioneer GM-X372 Manuel utilisateur

Pioneer

Pioneer GM-D7500M SERIES Manuel utilisateur

Pioneer

Pioneer GM-X372 Manuel utilisateur

Pioneer

Pioneer GM-6100F Manuel utilisateur

Pioneer

Pioneer GM6400F - Bridgeable Amplifier Manuel utilisateur

Pioneer

Pioneer GM-D8500M Manuel utilisateur

Pioneer

Pioneer GM-X564 Manuel utilisateur

Pioneer

Pioneer PRS-D5000SPL Manuel utilisateur

Pioneer

Pioneer GM-D8500M Manuel utilisateur

Manuels Amplificateur de voiture populaires d'autres marques

Cyfre

Cyfre CHACDMA-819 Manuel utilisateur

MTX

MTX Thunder Marine TM904 Manuel utilisateur

MTX

MTX Thunder TA Super TA92001 Mode d’emploi

Lanier

Lanier 480-0239 Instructions d'utilisation et d'entretien

Kenwood

Kenwood KAC-642 Manuel utilisateur

Jensen

Jensen XA4150 Manuel utilisateur

Sony

Sony XM-405EQX Marketing Specifications Manuel utilisateur

Audiopipe

Audiopipe AQX-660.2 Manuel utilisateur

Clarion

Clarion APA2001 APA2001 APA2001 Guide de démarrage rapide

Sony

Sony XM-7547 Manuel utilisateur

Alpine

Alpine PDX11000 - Amplifier Manuel utilisateur

Steg

Steg Qx Mos 105.4x Manuel utilisateur

JL Audio

JL Audio HD900/5 Manuel utilisateur

Memphis

Memphis 16-MC5.700 Manuel utilisateur

Audiopipe

Audiopipe APSM-1150 Manuel utilisateur

Boss Audio Systems

Boss Audio Systems Riot GT1000M Manuel utilisateur

Kenwood

Kenwood KAC-PS811D Manuel utilisateur

Fusion

Fusion CA-DA41400 Manuel utilisateur