Pilot RC Extra 330SC Manuel utilisateur
PilotRC Extra 330SC 67”
USER MANUAL
WINGSPAN:1714mm
LENGTH:1600mm
Thank you for purchasing our new 30cc aerobatic plane. we strive to achieve a good
quality quick build ARF aircraft .
It requires the least amount of assembly of any ARF kit to obtain the maximum
performance.
Both the design and manufacturing have been undertaken to the highest standards,
using best quality hardware, covering, wood & glue during factory construction stage.
By optimal weight and balance along with reliable construction, you will find this plane
ideal for 3D - Freestyle and aerobatic flying.
We hope that every effort and service we offer will, in turn, give
you confidence using PILOT Models.
Have a wonderful time flying your 3D aircraft in a suitable safe space!
Introduction
Warrant
● All Pilot-RC products are guaranteed against defects for 30 days of receiving your
airplane. This warranty is limited to construction or production defects in both material and
workmanship , it does not cover any component parts damaged through use or
modification .
● The manufacture cannot supervise the assembly, operation or maintenance, and is not
responsible for radio malfunctions. Please ensure your radio system is in good condition.
We are not responsible for any accident or damage while using this product. It is
impossible to determine for certain whether crash damage was the result of improper
installation of our products, a radio system failure, or pilot error. Model airplane owners use
our products at their own risk.
●
Pilot
-
RC will not be liable for any costs, unless agreed and proved beyond doubt the
●
Pilot
-
RC will not be liable for any costs, unless agreed and proved beyond doubt the
failure was due to faulty materials or fabrication. Any agreed cost will not exceed the cost
of the airframe and not include engine, radio equipment or third party claims.
● Should you wish to return a product or receive replacement parts, all shipping cost must
be paid by the customer.
Attention
● 1. Do not regard this plane as a toy!
● 2. To ensure safety, please read the instruction manual thoroughly before assembly.
● 3. Building and operating an RC Plane of this nature
requires previous experience and competence to an experienced level. This plane is not for
a beginner!
● 4. If you are in doubt have an experienced pilot at hand. Diligent practicing and correct
guidance is essential, accidents can cause bodily harm and property damage.
● 5. Seek assistance from an experienced person or airplane model clubs in assembly,
operation and maintenance to ensure successful training.
● 6. Fly only in a registered RC model club airfield that is approved by your local
Academy of Model Aeronautics (AMA).
● Pilot-RC has the right to revise the plane, the instructions and the limited warranty
without notice. If you have any problems and questions please contact Pilot –RC：
Email: pilot[email protected] , info@pilot-rc.com
Phone:+86 760 88781293
FAX: +86 760 88780293
Address: No.34, Chengnan Er Road , Zhongshan city, 528400, Guangdong Province, China
Included Hardware:
• Complete air frame with all basic accessories (such as carbon fibre main
undercarriage, tail-gear assembly and wing-tube as well as fibreglass control
horns and wheel pants)
• Ready to install hinges and pre-mounted canopy
• Wheels, axels and wheel pants
• Pushrods with ball links
• Matching plastic spinner
• Wing bags
• Servo extension wires
Propeller: 15x8E
Also requires all the usual accessories such as transmitter, receiver, propeller,
batteries, powerbox, extension leads and possibly other small accessories.
Engine Option 1 : Gasoline
Transmitters and Receivers
equired Hardware:
Transmitters and Receivers
Gasoline engine - 20cc ) (for example DLE-20RA)
Servos (5pcs) (for example Pilot-RC PY-20AL)
Batteries of your choice - RX and / or Ignition
Engine Option 2: Electric
Transmitters and Receivers
Servos (4pcs) (for example Pilot-RC PY-20AL)
Electric motor (Pilot-RC CC20/400KV motor)
ESC (100A )
Batteries of your choice (3300-4500mah 6S 22.2V 35C lipo battery)
Other Accessories Needed To Complete:
• Epoxy Adhesives
• Cyanocrylate adhesives
• X-Acto and Saw knives
• Sandpaper
• Thread lock
• Aircraft stand or support
• Drill, screw drivers, allen keys, wrench set, pliers, etc
Main Landing Gear Assembly
Position the fuselage upside down and screw on the carbon undercarriage to
the fuselage using the nuts and bolts provided.
Screw the wheel axles on to the landing gear, and then slide on the wheels
and secure in place with the provided grub screws.
Some users may prefer to leave the wheels until the end of the build, to
prevent the model moving on the build table.
Tail wheel Installation
With the model still upside down, position the carbon tail wheel unit on its
correct location and mark on the underside of the fuselage to drill the holes
for the screws that will hold the tail wheel in place.
Screw the tail wheel unit to the fuselage using the blind nuts and bolts
provided.Attach the springs to the underside of the rudder using the metal
arm supplied.
We recommend to keep the pivot point of the tail wheel as in line with the
We recommend to keep the pivot point of the tail wheel as in line with the
hinge line as possible to assure a bind free movement of the springs.
Servo Horn On The Elevator Installing:
It is very important to sand horn to assure a strong bond once glued to
the model.
Locate and cut the covering where the horns will be glued
Glue them to the surface using epoxy glue
Excess epoxy glue can be removed with acetone
Servo Horn On The Ailerons Installing:
Servo Horn On The udder Installing:
It is very important to sand horn to assure a strong bond once glued to the
model.
Locate and cut the covering where the horns will be glued
Glue them to the surface using epoxy glue
Excess epoxy glue can be removed with acetone
It is very important to sand horn to assure a strong bond once glued to the
model.
Locate and cut the covering where the horns will be glued
Glue them to the surface using epoxy glue
Excess epoxy glue can be removed with acetone
Aileron Servo Installation:
Install and glue the included hinges.
Locate and cut the covering where the servos will be installed.
Route the servo wire through the wing and screw the servo in place.
Centre the servo with your transmitter, attach the servo arm and connect the
servo to the ailerons with the pushrods provided.
Stabilizer installation:
Cut free the trailing edge of the vertical rudder in line with the stabiliser, in
order to allow you to slide the stabiliser into the fuselage. Keep the
removed section for later.
Trial fit the stabiliser into the fuselage. Make sure that it is centered
(measure the tip of the stabiliser to the tip of the wing on both sides and
make sure they are the same distance) and correctly aligned (looking at
wings and stabiliser, should show all being parallel)
Once centred and aligned, mark where it meets the fuselage. Remove
the stabiliser and carefully cut the covering on the inside of your mark, for
gluing.
Prepare a mix of Epoxy and generously coat the inside of the fuselage
where the stabiliser will fit, then re-insert the stabiliser into its final location,
checking again that it is centred and aligned.
Glue back into place the section removed earlier in this process.
Excess epoxy glue can be removed with acetone
udder Servo Installation:
Install and glue the included hinges.
Locate and cut the covering where the servo will be installed, at the rear of
the fuselage, under the elevator.
Route the servo wire through the wing and screw the servo in place.
Centre the servo with your transmitter, attach the servo arm and connect the
servo to the ailerons with the pushrods provided.
Elevator Servo Installation:
Install and glue the included hinges.
Locate and cut the covering where the servo will be installed, at the rear of
the fuselage, under the elevator.
Route the servo wire through the wing and screw the servo in place.
Centre the servo with your transmitter, attach the servo arm and connect the
servo to the ailerons with the pushrods provided.
Autres manuels pour Extra 330SC
1
Autres manuels Pilot RC Jouet
Pilot RC
Pilot RC Yak 54 Manuel utilisateur
Pilot RC
Pilot RC 50cc Yak-54 Manuel utilisateur
Pilot RC
Pilot RC Extra 330SC Manuel utilisateur
Pilot RC
Pilot RC 30cc 88" Skywolf Manuel utilisateur
Pilot RC
Pilot RC Extra NG - 67 Manuel utilisateur
Pilot RC
Pilot RC EDGE540 Manuel utilisateur
Pilot RC
Pilot RC 50cc Yak-54 Manuel utilisateur
Pilot RC
Pilot RC Decathlon Manuel utilisateur
Pilot RC
Pilot RC Foamy Manuel utilisateur
