Pickering 43-921 Manuel utilisateur
Page (ii)
© Copyright (2023) Pickering Interfaces. All Rights Reserved.
No part of this publication may be reproduced, transmitted, transcribed, translated or stored in any form, or by any
means without the written permission of Pickering Interfaces.
Technical details contained within this publication are subject to change without notice.
FM38792
Page (iii)
Worldwide Technical Support and Product Information
Pickering Interfaces Headquarters
Stephenson Road, Clacton-on-Sea, CO15 4NL United Kingdom
Tel: +44 (0)1255-687900
e-mail: [email protected]
USA
Tel: (West) +1 541 471 0700
Tel: (East) +1 781 897 1710
e-mail: ussales@pickeringtest.com
France
Tel +33 9 72 58 77 00
e-mail: [email protected]
Germany
Tel: +49 89 125 953 160
e-mail: [email protected]
Sweden
Tel: +46 340-69 06 69
e-mail: [email protected]
Czech Republic
Tel: +420 558 987 613
e-mail: [email protected]
China
Tel: +86 4008 799 765
e-mail: [email protected]
Technical Support
For Technical Support please contact Pickering Interfaces either by phone, the website or via e-mail.
Warranty
All products manufactured by Pickering Interfaces are warranted against defective materials and workmanship for a period
of three years, excluding programmable power supplies, from the date of delivery to the original purchaser. Any product
found to be defective within this period will, at the discretion of Pickering Interfaces be repaired or replaced.
Products serviced and repaired outside of the warranty period are warranted for ninety days.
Extended warranty and service are available. Please contact Pickering Interfaces by phone, the website or via e-mail.
Environmental Policy
Pickering Interfaces operates under an environmental management system similar to ISO 14001.
Pickering Interfaces strives to fulfil all relevant environmental laws and regulations and reduce wastes and releases to the
environment. Pickering Interfaces aims to design and operate products in a way that protects the environment and the health
and safety of its employees, customers and the public. Pickering Interfaces endeavours to develop and manufacture products
that can be produced, distributed, used and recycled, or disposed of, in a safe and environmentally friendly manner.
Page (iv)
Meaning/Description Symbol
PROTECTIVE EARTH (GROUND)
To identify any terminal which is intended for connection to an
external conductor for protection against electric shock in case of a
fault, or the terminal of a protective earth (ground) electrode.
DANGEROUS VOLTAGE
To indicate hazards arising from dangerous voltages.
WARNING/CAUTION
An appropriate safety instruction should be followed or caution to a
potential hazard exists.
Refer to the relevant instructions detailed within the product
manual.
HEAVY
If this product is heavy reference should be made to the safety
instructions for provisions of lifting and moving.
STATIC SENSITIVE
To indicate that static sensitive devices are present and handling
precautions should be followed.
!
kg
Safety Symbols
The following safety symbols may be used on the product and throughout the product documentation.
Product Safety
Page (v)
Contents
Copyright Statement........................................................................................................................................................(ii)
Technical Support and Warranty...................................................................................................................................(iii)
Product Safety...................................................................................................................................................................(iv)
Contents (this page).........................................................................................................................................................(v)
Warnings and Cautions...................................................................................................................................................(vi)
Section 1
Technical Specification....................................................................................................................................................1.1
Section 2
Technical Description ......................................................................................................................................................2.1
Hardware Description................................................................................................................................................2.1
53-921 Layout Connectors & Indicators..................................................................................................................2.1
43-921 Layout Connectors & Indicators..................................................................................................................2.2
Section 3
Installation.........................................................................................................................................................................3.1
Pre Operation Checks ................................................................................................................................................3.1
Installation of 53-921 in Host PC .............................................................................................................................3.1
Installation of 43-921 in PXIe Chassis.....................................................................................................................3.3
Cabling Host Computer to a PXIe Chassis..............................................................................................................3.5
Power ON/OFF Sequence ........................................................................................................................................3.5
Section 4
Trouble Shooting..............................................................................................................................................................4.1
Section 5
Maintenance Information................................................................................................................................................5.1
Page (vi)
WARNING - Hazardous Environments Symbol
This product is not specifically designed for use in hazardous environments, for example in explosive
atmospheres. If the product is to be used in hazardous environments we recommend that the user ensures
suitable protective measures are taken.
!
CAUTION - Handling of Electrostatic-Sensitive Devices Symbol
Certain semiconductor devices used in this equipment are liable to damage due to static voltage. Observe the
following precautions when handling these devices in their unterminated state, or sub-assemblies containing
these devices:
• Persons removing sub-assemblies from equipment using these devices must be earthed by a wrist strap
and a resistor at the point provided on the equipment.
• Soldering irons used during the repair operations must be low voltage types with earthed tips and isolated
from the mains voltage by a double insulated transformer.
• Outer clothing worn must be unable to generate static charges.
• Printed Circuit Boards (PCBs) fitted with these devices must be stored and transported in anti-static bags.
Warnings & Cautions
WARNING - Danger of Electric Shock Symbol
This module may contain hazardous voltages. Before removing the module from the rack remove all supplies
and disconnect user I/O signals.
Unused slots in the PXI/PXIe/LXI chassis are populated with blanking plates to prevent access to user I/O
signals that may be present. Blanking panels are available to order from Pickering in a variety of slot widths.
If the product is not used in this manner for example by using an extender card then additional care must be
taken to avoid contact with exposed signals.
CAUTION - Product Documentation Symbol
Suitably qualified & trained users should ensure that the accompanying documentation is fully read and
understood before attempting to install or operate the product.
!
Safety Instructions
Safety Instructions
All cleaning and servicing requires the equipment to be isolated and disconnected from the power source and user I/O signals
(refer to the Maintenance Section).
• Appropriate manual handling procedures should be followed as dictated by the weight of the individual module or the
combined weight of the modules & chassis.
• Should a fault occur with the module or chassis, immediately isolate and disconnect the incoming power to the chassis and
the user I/O signals.
• Ensure the equipment is installed, operated and maintained by trained and authorised personnel.
• For suitably equipped products in the event of an emergency press the red “emergency stop” button situated on the front of
the unit.
Page 1.1 pickeringtest.com
Section 1 - Technical Specification
yPXI-5 PXI Express Hardware Specification rev.2.0
Compliant
yPCI Express® Base Specifications rev.2.0 Compliant
yPCIe Gen 2 x8 Ports Each Support up to 4 GB/s
yPXI Express Link Capability:
- Four Link Configuration: x4 x4 x4 x4
- Two Link Configuration: x16 x8
yExpansion Distance up to 5 m With 2 m or 5 m
Expansion Cables
yComprehensive Hardware & Software Transparency
yFlexible Option for Multi-chassis Expansion
as a Daisy-chain or Star-chain Configured
y3 Year Warranty
Control of two PXIe Chassis -
43-921-001 Control Interface in
First Chassis Daisy-chained to
43-921-002 Control Interface in
Second Chassis
Controller PC
12
Interface Cable
53-921-001 Card
(PCIe X8 Connector
in Host Computer)
43-921-001 Module
(System Slot in PXIe Chassis)
3 4 5 6 7
PXIe Chassis
123 4 5 6 7
PXIe Chassis
43-921-002 Module
(System Slot in PXIe Chassis)
Interface Cable
8
8
Controller PC
12
Interface Cable
53-921-001 Card
(PCIe X8 Connector
in Host Computer)
43-921-002 Module
(System Slot
in PXIe Chassis)
3 4 5 6 7
PXIe Chassis
123 4 5 6 7
PXIe Chassis
43-921-002 Module
(System Slot
in PXIe Chassis)
Interface Cable
8
8
43-921-003 Module
(Peripheral Slot
in PXIe Chassis)
The 43-921 PCI Express-to-PXI Express expansion kit allows
control of PXI Express modules installed in a PXI Express
chassis using high bandwidth PCI Express technology. The
extension kit provides up to 4 GB/s using PCIe Gen 2 x8
signalling. The 43-921 PCI Express-to-PXI Express expansion
kit provides additional PXI instrument slots to the host
computer by implementing a PCI Express-based control of
PXI modules. The technology consists of a 53-921-001 adapter
card installed in the host computer, a PCIe x8 cable, and a
43-921-00x 3U (Eurocard) remote control interface module.
The 53-921-001 comes in a PCI Express x8 footprint and is
equiped with a PCIe x8 cable connector.
The 43-921-001 with dual ports has the capability of multi-
chassis control in a daisy-chain configuration. The upper port
is connected to a 53-921-001 installed in a host PC and the
lower port is connected to a 43-921-002 in the system slot of
a second chassis. Alternatively, a 43-921-003 module fitted to
a peripheral slot in the first chassis can be used to control the
43-921-002 module in the second chassis - see diagram below.
With comprehensive hardware and software transparency, the
expansion kit enables fast and convenient detection of any PXI
cards installed in the system, requiring no additional drivers
or software.
Alternative Control of two PXIe
Chassis - 43-921-003 Peripheral
Interface in First Chassis Daisy-
chained to 43-921-002 Control
Interface in Second Chassis
pickeringtest.com
43-921
PCIe to PXIe Remote Control Interface
Issue 1.1 August 2023
Page 1.2 pickeringtest.com
Section 1 - Technical Specification
Specification
Compliance: PXI-5 PXI Express hardware
specification Rev.2.0 compliant
Maximum Data Throughput: 43-921-001: Two PCIe gen 2 x8
ports each up to 4 GB/s
43-921-002: PCI Express gen 2
x8 link with 4 GB/s
Connection Distance: Up to 5 m
Installation: Controller slot 1
(43-921-001 and 43-921-002)
Dimensions - 53-921-001: Low-profile PCI Express card:
142 mm (W) x 69 mm (H)
Dimensions - 43-921-00x: PXI Express system module:
175 mm (W) x 107 mm (H)
Product Order Codes
PCIe-to-PXIe Kit with 2 m Cable
with Daisy-chain Facility
43-921-001-KIT
(includes one 53-921-001, one 43-921-001 and one
43-921-200 2 meter cable)
PCIe-to-PXIe Kit with 2m Cable 43-921-002-KIT
(includes one 53-921-001, one 43-921-002 and one
43-921-200 2 meter cable)
PCIe Remote Control Interface Card
(for fitting to Host PC)
PCIe Low Profile Front Panel
(for use with 53-921-001 Interface Card)
PXIe Remote Control Interface Module
with Daisy-chain Facility
(for fitting to PXIe System Controller Slot)
PXIe Remote Control Interface Module
(for fitting to PXIe System Controller Slot)
PXIe Remote Control Interface Module
(for fitting to PXIe Peripheral/Hybrid Slot)
Interface Cable 2 m
Interface Cable 5 m
53-921-001
53-921-LPF
43-921-001
43-921-002
43-921-003
43-921-200
43-921-500
Safety & CE Compliance
All modules are fully CE compliant and meet applicable EU
directives: Low-voltage safety EN61010-1:2010,
EMC Immunity EN61326-1:2013,
Emissions EN55011:2009+A1:2010.
43-921 Remote Control
Interface Fitted to 42-925
18-Slot PXIe Chassis
43-921 Remote Control
Interface Fitted to 42-924
8-Slot PXIe Chassis
Operating/Storage Conditions
Operating Temperature:
Humidity:
0 °C to +55 °C
10 % to 90 % non-condensing
Storage/Transport Temperature:
Humidity:
-20 °C to +75 °C
10 % to 90 % non-condensing
43-921
pickeringtest.com Page 2
Specifications & Odering Information
Page 2.1 pickeringtest.com
Section 2 - Technical Description
Hardware Description
Figure 2.1 - PCIe to PXIe Interface Kit Functional Block Diagram
PXIe Slot 1
PXIe Slot 2
PXIe Slot n
PLX Switch
43-921-00x
Remote PXIe Chassis
PCIe Gen2
x4x4x4x4
or x8x16
PLX Switch
53-921-001 PCIe Gen2 x8
External Cable
PCIe Gen2 x8
via Edge Connector
Host PC
Switches
‘SW1’
Connector for
PCIe x8 External
Cable
PCIe x8 Edge
Connector
‘STATUS’ Indicator
‘HOST’ Indicator
Functional Block Diagram
53-921 Layout Connectors & Indicators
Figure 2.2 - 53-921 PCIe Remote Control Interface Card Mechanical Layout
Page 2.2 pickeringtest.com
Section 2 - Technical Description
Indicator/Switch Description
‘STATUS’ Indicator
Off: No power
Orange: Power OK
Green: 43-921 present
‘HOST’ Indicator
(Link status between
53-921 and 43-921)
Off: No link
0.5Hz Blinking: Link in PCIe Gen1 signaling
1Hz Blinking: Link in PCIe Gen2 signaling
‘SW1’ Switch Default settings are switch 3 ON and switches 1, 2, 4 OFF
Table 2.1 - 53-921 Indicators & Switches
Connector
for PCIe x8
External
Cable
‘PWR/PRSNT’
Indicator
‘LINK’
Indicator
43-921 Layout Connectors & Indicators
Figure 2.3 - 43-921 PXIe Remote Control Interface Module Mechanical Layout
Indicator Description
‘PWR/PRSNT’ Indicator
Off: No power
Orange: Power OK
Green: 53-921 present
‘LINK’ Indicator
(Link status between
53-921 and 43-921)
Off: No link
0.5Hz Blinking: Link in PCIe Gen1 signaling
1Hz Blinking: Link in PCIe Gen2 signaling
Table 2.2 - 43-921 Indicators
Table des matières
Autres manuels Pickering Équipement d'enregistrement
Manuels Équipement d'enregistrement populaires d'autres marques
Strymon
Strymon NIGHTSKY Manuel utilisateur
Mitsubishi Electric
Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Manuel utilisateur
Tews Technologies
Tews Technologies TPMC465 Manuel utilisateur
Honeywell
Honeywell Excel 50 Manuel utilisateur
SeaLevel
SeaLevel COMM+8.LPCI Manuel utilisateur
Arturia
Arturia AUDIOFUSE STUDIO Manuel utilisateur
