Pickering 20-610 Manuel utilisateur

Page (1)

UNIVERSAL MULTIPLEXER MODULE 20-610

pickering

Issue 5.1 July 2019

User Manual

GPIB Universal Multiplexer Module

(Model No. 20-610)

pickeringtest.com pickering

SYSTEM 10/20

*Please contact Pickering for alternative

PXI/LXI/USB solutions

Page (II) UNIVERSAL MULTIPLEXER MODULE 20-610

pickering

Page (II) REED RELAY MODULE 40-110/115/120/125

pickering

No part of this publication may be reproduced, transmitted, transcribed, translated or stored in any form, or by

any means without the written permission of Pickering Interfaces.

Technical details contained within this publication are subject to change without notice.

ISO 9001

Reg No. FM38792

Page (III)

UNIVERSAL MULTIPLEXER MODULE 20-610

pickering

Page (III)

REED RELAY MODULE 40-110/115/120/125

pickering

TECHNICAL SUPPORT

For Technical Support please contact Pickering Interfaces either by phone, the website or via e-mail.

WARRANTY

All products manufactured by Pickering Interfaces are warranted against defective materials and workmanship for a period of

three years, excluding programmable power supplies, from the date of delivery to the original purchaser. Any product found to be

defective within this period will, at the discretion of Pickering Interfaces be repaired or replaced.

Products serviced and repaired outside of the warranty period are warranted for ninety days.

Extended warranty and service are available. Please contact Pickering Interfaces by phone, the website or via e-mail.

ENVIRONMENTAL POLICY

Pickering Interfaces operates under an environmental management system similar to ISO 14001.

Pickering Interfaces strives to full all relevant environmental laws and regulations and reduce wastes and releases to the

environment. Pickering Interfaces aims to design and operate products in a way that protects the environment and the health and

safety of its employees, customers and the public. Pickering Interfaces endeavours to develop and manufacture products that can

be produced, distributed, used and recycled, or disposed of, in a safe and environmentally friendly manner.

Worldwide Technical Support and Product Information

pickeringtest.com

Germany

Tel: +49 89 125 953 160

E-mail: [email protected]

Sweden

Tel: +46 340-69 06 69

E-mail: [email protected]

USA

Tel: (West) +1 541 471 0700

Tel: (East) +1 781 897 1710

E-mail: [email protected]

Czech Republic

Tel: +420 558 987 613

E-mail: [email protected]

France

Tel +33 9 72 58 77 00

E-mail [email protected]

Pickering Interfaces Headquarters

Stephenson Road Clacton-on-Sea CO15 4NL United Kingdom

Tel: +44 (0)1255-687900

E-Mail: [email protected]

China

Tel: +86 4008 799 765

E-mail: [email protected]

Page (IV) UNIVERSAL MULTIPLEXER MODULE 20-610

pickering

Page (IV) GENERAL PURPOSE REED RELAY MODULE 10-110/115/120/125

pickering

Page (IV) REED RELAY MODULE 40-110/115/120/125

pickering

MEANING / DESCRIPTION SYMBOL

PROTECTIVE EARTH (GROUND)

To identify any terminal which is intended for connection to an external conductor for

protection against electric shock in case of a fault, or the terminal of a protective earth

(ground) electrode.

DANGEROUS VOLTAGE

To indicate hazards arising from dangerous voltages.

WARNING / CAUTION

An appropriate safety instruction should be followed or caution to a potential hazard

exists.

Refer to the relevant instructions detailed within the product manual.

HEAVY

If this product is heavy reference should be made to the safety instructions for

provisions of lifting and moving.

STATIC SENSITIVE

To indicate that static sensitive devices are present and handling precautions should

be followed.

SAFETY SYMBOLS

PRODUCT SAFETY

The following safety symbols may be used on the product and throughout the product documentation.

Page (V)

UNIVERSAL MULTIPLEXER MODULE 20-610

pickering

Technical Support and Warranty................................................III

Product Safety .............................................................................IV

Contents (this page)....................................................................V

Warnings and Cautions ..............................................................VII

Section 1

Technical Specication...............................................................1.1

Section 2

Technical Description .................................................................2.1

Functional Description..........................................................2.1

Section 3

Installation....................................................................................3.1

Pre-Operation Checks...........................................................3.1

Hardware Installation ............................................................3.1

Software Installation .............................................................3.3

Self-Test..................................................................................3.3

Section 4

Programming Guide....................................................................4.1

Programming the Module .....................................................4.1

Section 5

Connector Information................................................................5.1

Section 6

Trouble Shooting.........................................................................6.1

Installation Problems ...........................................................6.1

Maintenance Information............................................................7.1

Relay Lookup Tables.............................................................7.1

PCB and Component Layout................................................7.2

Appendix ......................................................................................A.1

Conguration Schematics....................................................A.1

CONTENTS

Please use the hyperlinked text to navigate to the page required

Page (VI) UNIVERSAL MULTIPLEXER MODULE 20-610

pickering

THIS PAGE INTENTIONALLY BLANK

Page (VII)

UNIVERSAL MULTIPLEXER MODULE 20-610

pickering

Page (VII)

GENERAL PURPOSE REED RELAY MODULE 10-110/115/120/125

pickering

WARNINGS AND CAUTIONS

WARNING - HAZARDOUS ENVIRONMENTS SYMBOL

This product is not specically designed for use in hazardous environments, for example in explosive

atmospheres. If the product is to be used in hazardous environments we recommend that the user

ensures suitable protective measures are taken.

WARNING - DANGER OF ELECTRIC SHOCK SYMBOL

This module may contain hazardous voltages. Before removing the module from the rack remove all

supplies and disconnect user I/O signals.

Unused slots in the System 10/20 chassis are populated with blanking plates to prevent access

to user I/O signals that may be present. Blanking panels are available to order from Pickering in a

variety of slot widths. If the product is not used in this manner for example by using an extender card

then additional care must be taken to avoid contact with exposed signals.

CAUTION - HANDLING OF ELECTROSTATIC-SENSITIVE DEVICES SYMBOL

Certain semiconductor devices used in this equipment are liable to damage due to static voltage.

Observe the following precautions when handling these devices in their unterminated state, or

sub-assemblies containing these devices:

1. Persons removing sub-assemblies from equipment using these devices must be earthed by a

wrist strap and a resistor at the point provided on the equipment.

2. Soldering irons used during the repair operations must be low voltage types with earthed tips and

isolated from the mains voltage by a double insulated transformer.

3. Outer clothing worn must be unable to generate static charges.

4. Printed Circuit Boards (PCBs) tted with these devices must be stored and transported in

anti-static bags.

CAUTION - PRODUCT DOCUMENTATION SYMBOL

Suitably qualied & trained users should ensure that the accompanying documentation is fully read

and understood before attempting to install or operate the product.

SAFETY INSTRUCTIONS

All cleaning and servicing requires the equipment to be isolated and disconnected from the power source and user I/O

signals (refer to the Maintenance Section).

• Appropriate manual handling procedures should be followed as dictated by the weight of the individual module or

the combined weight of the modules & chassis.

• Should a fault occur with the module or chassis, immediately isolate and disconnect the incoming power to the

chassis and the user I/O signals.

• Ensure the equipment is installed, operated and maintained by trained and authorised personnel.

Page (VIII) UNIVERSAL MULTIPLEXER MODULE 20-610

pickering

THIS PAGE INTENTIONALLY BLANK

Page 1.1

UNIVERSAL MULTIPLEXER MODULE 20-610

pickering SECTION 1 - TECHNICAL SPECIFICATION

SECTION 1 - TECHNICAL SPECIFICATION

pickeringtest.com

GPIB Universal Multiplexer Module 20-610

ISSUE 4.2 JUL 2019

• Very High Density 352 Pin Multiplexer

• Dual or Quad Multiplexer Operation, Switching

1 or 2 Poles

• Expandable to 10,000 Channels Using Internal

Analogue Bus

• Automatic Isolation Switches Reduce

Capacitive Loading in Large Systems

• High Quality Ruthenium Reed Relays For

Maximum Reliability

• Built-In Self Test

• Suitable for Ribbon Cable Connection

• Versatile Conﬁguration Options: “One Module

for ALL Your General Purpose Multiplexer

Applications”

• Built-In RS-232 Port

Quad MUX Mode: 44 Channels

Bank 1

Common

Bank 2

Common

Bank 3

Common

Bank 4

Common

Bank 1

Bank 2

Common 1

Common 2

Dual MUX Mode:

88 Channels

The 20-610 Universal 352 Pin Multiplexer Module was the rst in

a new generation of very high density multiplexers from Pickering

Interfaces. One standard module offers a very large range of

switching possibilities plus extensive built in self-test.

Model 20-610 offers the very highest density multiplexing with 352

switch pins.

Universal Multiplexer - For Now & The Future

The 20-610 may be used for most general purpose multiplexer

requirements. The analogue common/s may be routed to the front

panel or, for large system implementation, to one of the internal

analogue buses. This versatility means that one multiplexer

module is suitable for many different applications.

Simple Internal Expansion to 10,000 Channels

Up to 2816 input channels can be accommodated in one System

20 Case, over 10,000 with multiple expansion cases.

Built-in Automatic Isolation Switching connects only the currently

active multiplexer switch bank, thereby keeping capacitive loading

and leakage currents in large multiplexer systems to a minimum.

*Please contact Pickering for alternative

PXI/LXI/USB solutions

Page 1.2 UNIVERSAL MULTIPLEXER MODULE 20-610

pickering

SECTION 1 - TECHNICAL SPECIFICATION

Universal Multiplexer Module – 20-610

pickeringtest.com

Overview

Common

1.1

2.1

88.1

1.1

2.1

88.1

Isolation

Switch

Isolation

Switch

Bank 1

Bank 2

Common

1.2

1.1

2.2

2.1

44.2

44.1

Common

1.2

1.1

2.2

2.1

44.2

44.1

Isolation

Switches

Isolation

Switches

Bank 1

Bank 2

Common

1.2

1.1

2.2

2.1

44.2

44.1

Common

1.2

1.1

2.2

2.1

44.2

44.1

Isolation

Switches

Isolation

Switches

Bank 3

Bank 4

Dual 88 Channel 1-Pole

20-610-021

Quad 44 Channel 2-Pole

20-610-022

Bank 4

2 Pole

Bank 3

2 Pole

Bank 2

2 Pole

Bank 1

2 Pole

Bank 0

2 Pole

Common Out

Bank 6

2 Pole

Bank 5

2 Pole

Internal 24-Pole Analogue Bus

Chan 1-176 Chan 177-352 Chan 353-528 Chan 529-704 Chan 705-880 Chan 881-1056 Chan 1057-1232

Power Supply

GPIB/RS-232

Interface

20-610-022

Up to 8 Multiplexers can be housed

per case, larger systems are formed

using master/slave case expansion

20-610-022 20-610-022 20-610-022 20-610-022 20-610-022 20-610-022 20-610-022

Creating Larger Multiplexers

When more than one module is used to make up a multiplexer –

see diagram below, where seven modules are used to make up a

1232 channel 2-pole multiplexer – then all multiplexer units must

have the same internal address, the location of each module within

the multiplexer is given by its own bank address. Bank addresses

must start at 0 and should be contiguous.

If there is a problem with any of the modules used to make

up a large multiplexer then an error will be detected (use the

REPORT? query to discover the cause).

Analogue Bus

The analogue common can be routed (using internal jumpers)

out to either the front panel connectors or the internal analogue

bus. Routing to the front panel allows the user complete exibility,

routing to the internal analogue bus simplies large system

construction and ensures good signal isolation from external

interference.

The System 10/20 backplane features a shielded 24 pole analogue

bus. This would be used with a multiplexer constructed using more

than one module where the selected channel will be carried along

the backplane analogue bus.

Built-In RS-232 Port

The 20-610 also has a built in RS-232 port (9600 baud, XON/

XOFF, 8 bit, no parity). This is provided on a 4 pin Molex type

connector on the front panel. A separate adapter lead to allow use

with a standard 9 pin D-type is available. The RS-232 port allows

the module to be congured, controlled and monitored from any

RS-232 terminal. This can be a very versatile debugging aid.

Table des matières

Autres manuels Pickering Multiplexeur

Pickering

Pickering 50-670C Manuel utilisateur

Pickering

Pickering PXI 40-620 Manuel utilisateur

Pickering

Pickering 40-761 Series Manuel utilisateur

Pickering

Pickering LXI 60-820 Manuel utilisateur

Pickering

Pickering SYSTEM 10 Manuel utilisateur

Pickering

Pickering 40-616A Manuel utilisateur

Pickering

Pickering PXI 40-883A Manuel utilisateur

Pickering

Pickering 40-657 Manuel utilisateur

Pickering

Pickering 40-612A Manuel utilisateur

Pickering

Pickering 40-666A Manuel utilisateur

Pickering

Pickering 40-666 Manuel utilisateur

Pickering

Pickering 40-655A Manuel utilisateur

Pickering

Pickering PCI 50-670 Manuel utilisateur

Pickering

Pickering 40-681 Manuel utilisateur

Pickering

Pickering 40-657 Manuel utilisateur

Pickering

Pickering 40-670C Manuel utilisateur

Pickering

Pickering PXI 40-748 1 Series Manuel utilisateur

Pickering

Pickering 40-675A Manuel utilisateur

Pickering

Pickering 40-630A Manuel utilisateur

Pickering

Pickering LXI 60-890-053 Manuel utilisateur

Pickering

Pickering 40-614 Manuel utilisateur

Pickering

Pickering 40-658A Manuel utilisateur

Pickering

Pickering 40-735 Manuel utilisateur

Pickering

Pickering 40-760 Manuel utilisateur

Manuels Multiplexeur populaires d'autres marques

Campbell

Campbell AM416 Manuel utilisateur

Paradyne

Paradyne SIM2000 Manuel utilisateur

Panasonic

Panasonic WJFS616 - SWITCHER Manuel utilisateur

Lanex

Lanex TM-77 Manuel utilisateur

Bosch

Bosch VSS8394/01T Manuel utilisateur

Quark-Elec

Quark-Elec QK-A035 Manuel utilisateur

ADTRAN

ADTRAN Frameport 768 Manuel utilisateur

Elo TouchSystems

Elo TouchSystems E247 Manuel utilisateur

Paradyne

Paradyne Hotwire 8786 Manuel utilisateur

RFL Electronics

RFL Electronics 9508D UCC Manuel utilisateur

Miranda

Miranda AMX-101i Mode d’emploi

ShipModul

ShipModul MiniPlex-AIX NMEA-0183 Manuel utilisateur

GE StoreSafe SDVR-10 Manuel utilisateur

American Fibertek

American Fibertek MTX-8410C Manuel utilisateur

ADC

ADC HiGain ELU-319 5E Manuel utilisateur

Paradyne

Paradyne Hotwire 8774 Manuel utilisateur

American Fibertek

American Fibertek MTX-8810C-SL Manuel utilisateur

Viessmann

Viessmann 5229 Manuel utilisateur